How to change the third line to the sixth line, and how to change the two wires with brushed ESC to

The six-wire wiring of the timer is very regular, one side is two wires, one to the power supply, one to the gentle standard transfer switch, four wires there, the first two are to the gentle standard transfer switch, the long two lines are to the motor, as long as you master this law, you will not be wrong.

Damage to the mechanical timer is one of the most common faults in washing machine repairs. And it is often difficult to buy the original model of timer, and it is more troublesome to replace it. And because the timer generally has 6 wires, as well as 7, 8, 9 wires (with buzzer) types, therefore, the wiring sequence is very important when repairing and replacement.

Because among the many wiring, as long as the wrong wire is connected, the timer will not work.

The timer of 6 wires, generally in a group of 2, of which 1 power pack is connected to the power supply and 1 is connected to the common end of the piano key switch; The other 2 piano key switch groups; 2 connected capacitor banks. The difference between a timer with 7 wires and a timer with 6 wires is that 3 of the wires are connected to the key switch group. The difference between the timer of 8 wires and the 7 wires is that 1 more wire is connected to the buzzer, and the other wire of the buzzer is connected to the common end of the power supply.

The timer of 9 wires is different from 7 wires, and there are 2 more wires connected to the buzzer.

The wiring characteristics are: generally divided into three groups (or four groups, one of which is a buzzer line), a group of wires connecting the piano key switch is the shortest, generally with yellow, white, green (or blue) color wires. There is a group of wires, one long, one short, and the long wire is generally black (but there are a few other colors) connected to the power incoming wire, ** connected to the common end of the piano key switch.

The group of wires with the same length of the two wires, and the one of the capacitors connected to the group is generally the red line.

Hello! To change the brushed ESC from two wires to three wires, you need to perform the following steps:

1.Determine the type of brush ESC rolling: First, you need to determine the type of brush ESC you are using.

Some brush ESCs are designed as two-wire, while some are designed as three-wire. If your brush ESC is two-wire, then changing it to a three-wire may require some extra work.

2.Get the materials you need: To change the brush ESC from 2 to 3 wires, you'll need to get a baby and some additional materials, including an ESC shield and an adapter cable.

3.Connect the ESC Shield: Connect the ESC Shield to the brush ESC. According to the instructions or logos on the display board, connect it correctly to the output port of the flash ESC.

4.Connect the adapter cable: Connect the adapter cable to the ESC shield. One end of the adapter cable should be plugged into the appropriate port on the shield, while the other end should be plugged into the device you want to connect to, such as a motor.

5.Connect the power supply: Finally, connect the flash ESC and ESC expansion board to the power supply. Make sure you connect the power supply the right way to avoid any circuit shorts or other issues.

Please note that the above steps are only applicable to the general case of brushing the ESC from two to three wires. The specific steps may vary depending on the model and manufacturer of the ESC. Therefore, before making any changes, be sure to refer to the manual of the brush ESC you are using or consult the advice of a relevant professional.

To change the brush ESC from two to three wires, you need to perform the following steps:

1.Confirm the ESC type: First, determine if the brushed ESC you are using supports 3-wire control. Some brushed ESCs can only use two-wire control, but not three-wire control.

2.Purchase an adapter: If your brushed ESC supports three-wire control, but currently only has two wires (positive and negative) connected, you need to purchase an adapter, also known as:"Three-line retrofitting line"or"Three-wire switch"。

This adapter will be used to convert a two-wire connection of a brushed ESC into a three-wire connection slippery position.

3.Connect the adapter: Connect the adapter to the output of the two-letter strain of the brushed ESC.

Typically, the adapter will have three wires (positive, negative, and signal wires). Make sure that the cable that connects the adapter correctly is connected to the positive and negative poles of the brushed ESC, and that the signal cable of the adapter is connected to the control signal source (e.g., the remote control receiver).

4.Configuration Parameters: According to the manual of the brushed ESC you are using, configure the parameters of the ESC to adapt to the new 3-wire connection. You may need to configure parameters such as throttle travel range, reverse setting, etc., to ensure that the ESC works properly.

5.Test & Calibration: After the above connections and configurations have been completed, the test and calibration are performed. Make sure that the ESC can accurately adjust the speed and direction of the motor according to the control signal.

Please note that the above steps may vary slightly depending on the specific brushed ESC model and adapter model. Before making any modifications, be sure to read the instructions of the device in question and follow the corresponding operating guidelines.

1.Get an adapter: You'll need to buy an adapter that will convert the motor's signal into the three-wire signal you need. The choice of adapter depends on the type of motor and controller you are using.

2.Connect the adapter to the ESC: Connect the input of the adapter to the output of the ESC, usually through the power cable.

Then connect the output of the adapter to the three wires of the motor, one of which is the power line and the other two are the signal lines used to control the motor. Note that you need to connect the three wires of the motor correctly according to the type and specification of the motor.

3.Perform a test: Once the connection is complete, you will need to test to make sure that the adapter and motor are connected correctly and that the motor is working properly. You can use a remote control or other controller to control the speed and direction of the motor.

In general, if you want to change an ESC with only two wires to three wires, you need to get an adapter and connect it with the ESC and the motor. After completion, a test is performed to ensure that the motor is working properly.

Brush ESC is the connection between the motor governor and the brushless DC motor. If the ESC only has two wires, then it is a simple switch that does not provide a reversal function. If you need the reversal function, you need to change the ESC to a three-beam line ESC.

Here's how to change to a three-wire ESC:

1.Determine the positive and negative poles of the ESC, and connect the positive terminal of the battery and the positive terminal of the motor to the two ends of the ESC.

2.Connect the negative pole of the motor to ground, and connect the negative pole of the battery to the third wire end of the ESC.

3.Use a multimeter to measure the voltage at the two wire ends of the ESC, and if the motor does not rotate, you can adjust the center point of the ESC until the motor starts to rotate.

4.Test whether the motor can be rotated forward or reverse, if not, you can swap the two wire ends of the ESC.

5.Finally, solder the three wire ends of the motor and the ESC, and be careful not to short-circuit or connect the wrong wires to avoid damaging the ESC or the motor.

In general, it is not difficult for Zhichun to change the brush ESC to a three-wire ESC, as long as you follow the above steps, you can realize the function of forward and reverse rotation of the motor.