Win8 1 All in One Lenovo brand machine How to change the hard disk Thank you! 5

If you need to install Win7 and other earlier versions of the system, you need to convert it to MBR format, and you can use the diskpart command to complete the conversion.

Note: Converting disk format requires erasing all partitions and data in the disk, please save all important data in the disk before the operation.

Specific steps:1Use Win7 CD or USB flash drive to boot and enter the system installation interface.

2.Press Shift+F10 to open the Command Prompt.

3.Enter "diskpart" (no quotation marks, the same below) and press enter to enter the operation interface.

4.Enter list disk to view the disk information. Pay attention to the disk capacity to select the hard disk.

6.Enter "clean" to empty the current disk partition.

7.Enter "Convert MBR" to convert to MBR partition.

8.When the operation is complete, close this command prompt window and continue to install the win7 system according to the normal method.

Hello, change the system attention to back up the data.

You can refer to the operation steps and common problems of the notebook factory pre-installed win8 modification windows 7.

It's okay to set it up in the BIOS, if it doesn't work, you can ask Taofeng Computer, they are quite professional there.

1.Plug in the installation disc (don't use a clone of the GHO extension) and try to delete (select the partition and press the L key) the disk partition, which is the key to reinstalling the Windows 7 operating system.

2.Press the C key again to rebuild the partition, and the newly created partition will be recognized by the Windows 7 operating system installation CD.

3.After partitioning properly, don't forget to format the system disk (partition C), and then you can install the Windows 7 operating system normally.

4.After formatting the disk, the installation disc will automatically copy the files to the disk for automatic installation.

5.This is followed by steps such as collecting information, which are basically automatic.

6.Wait patiently, there will be an automatic restart in the middle of the process, and the whole installation process will not be completed until the reboot comes to the desktop again.

Dear ASUS users, Hello!

1. Before replacing the hard disk, use ASUS Backtracker to save the backup of the hidden partition files to a USB flash drive or portable hard disk (the capacity must be greater than 16GB), and after replacing the hard disk, start the recovery system through the USB flash drive.

2.Restore the system through this method, the computer hard disk partition will be restored to the factory state, the data in the hard disk will be cleared, before restoring the system, please back up the data in the computer to other external storage devices.

3.During backup and restore, make sure that both the battery and power adapter are connected to your computer to ensure that the computer does not lose power.

You need to use ghost software to partition the partition.

You don't understand the problem enough; Pure version you can **win8 original system,Follow the prompts one step once the operation of the book step can be,There are no programs in it,Including what QQ,Thunderbolt and the like,It's best to format all partitions before installation,Put the information you need in other hard disks; In addition, in order to achieve the maximum speed of the Rock Macro to the SSD, you need to set up the motherboard and 4K alignment, and you can follow these questions.

When entering the PE blue screen, change the configuration-sata controller mode to compatible, the boot mode to legacy support in boot, and the boot priority to legacy first in the BIOS.

Dear Lenovo users, hello!

Provide you with a way to change win8 to win7:

This model does not support the XP system, the motherboard chip is too new, and it can only be installed in the hope that it will help you.

Dear users, hello!

When installing Windows XP Lenovo OEM SP3, the blue screen error message is 0x000000a5.

It is due to the fact that 1. Intel Sharay and the above platforms have clearly not supported XP systems.

2. The XP system does not contain the AHCI driver files required by the platforms above Sharbay.

It seems that you want to prepare a U disk PE system When you use win7, enter PE to activate the partition where PE is located, set it as the main disk, and then enter to try.

Manual repair. Or find someone to guide you remotely. If you don't have a USB flash drive toolbox, you will send it for repair.

This is the drive disk, if you don't know how to install the system, you should go to the computer repair shop. Or buy a system disk by yourself, boot up F12, select ***, and choose to install the system to the first partition in it. Press F11 can also restore the factory, it is best to find a professional to help you repair.

This is the drive disc to power on press F11

Modify win7

Because it is a lower version of the win7 system to replace the higher version of the system.

So make a backup of your computer.

Full disk formatting.

to install win7.

Hope it helps the landlord.