How to wrap the rounded corners, how to cut the semi circular edging strips to the diagonals

Step Method:

1. Fold the two sides of the edging belt inward about half a centimeter and iron it flat.

2. Fold the edging tape in half and iron it flat.

3. The edging belt is backed to the fillet and a few stitches are stitched along the crease.

4. Turn over the edging tape, compare the length of the edging required for the round, fix it with a bead needle, and cut off the excess part.

5. Suture along the crease.

6. Turn over the edging belt, sort out the shape, and fix it with bead needles.

Tools Raw materials.

Bead needles, scissors, irons, needles, thread, edging tape, a rounded corner to be edging.

Step Method:

01Fold the two sides of the edging belt inward about half a centimeter and iron it flat.

02Fold the edging tape in half and iron it flat.

03 Hemming with the back to the rounded corners and a few stitches along the creases.

04 Turn over the edging tape, compare the length of the hemming required for the round, fix it with a bead needle, and cut off the excess.

05 Suture along the crease.

06Turn over the edging tape, tidy up the shape, and fix it with bead needles.

Unsupported formats.

07 Stitch along the crease with a hidden needle. In this way, the rounded corners are done.

Precautions. Lycra edging tape is expensive, soft and shiny, and is mostly used in boutique bags, such as golf club covers.

When cutting the diagonal of the semi-circular edging strip, you can follow these steps:

1.First, place the semi-circular edging strip on the workbench, making sure that its plane is level. Bibi.

2.Then, using a ruler or right angler, mark the two opposite edges of the semi-circular edging strip at the length of the radius from the edge.

3.Then, use a sharp cutting tool (such as a cutting knife, small saw, etc.) to cut slowly along these two marking lines, taking care to keep the knife edge perpendicular to the marking line, and control the depth and speed of the cutting to avoid damaging the material and socks.

4.Finally, the cut diagonal is sanded with fine sandpaper or polishing cloth to make it smooth and flat, and to remove any sharp edges that may remain.

It should be noted that the cutting direction and position must be confirmed before cutting to avoid mis-cutting or wasting materials. In addition, for beginners, you can practice cutting and rolling on waste materials until you are proficient in the technique before trying to operate it in a real project.

When cutting a semicircular edging strip, the following steps can be used to make the diagonal symmetry of the old side:

1.First, select a location, mark two vertices on the radius of the arc, and draw a random straight line between the vertices.

2.Flip the cut semicircle to the other side and attach it to the original semicircle so that the bottoms of the two semicircles coincide.

3.Through the common bottom of the two semicircles, the center point of the cut line can be accurately found. Mark the center point.

4.Using the center point of the marker, connect the bases of the two semicircles, thus dividing the two semicircles into two symmetrical triangles.

5.Divide the semicircle into two halves along the diagonal line to obtain two symmetrical semicircular arc edging strips.

It should be noted that in practice, appropriate tools and materials should be selected, and safety protection should be strengthened to avoid accidental injuries to the oak.

1 First of all, you need to place the semi-circular edging strip on the work surface and determine the two positions that need to be diagonal.

2 Align the ruler at the ends of the two positions where the diagonal line is required, and draw a straight line between the sails.

3 Cut the cutting tool slowly along a straight line until the entire semicircle edging strip is cut off. Posture opens.

Extension: When cutting semi-circular edging strips, you need to pay attention to the sharpness and force control of the knife to avoid damaging the work surface or accidentally injuring your hands.

It is recommended to make a test cut before cutting to determine the cutting method and strength.