How to connect wirelessly between the monitor and the main unit

The monitor and the host unit can be wirelessly connected through a microcast device, and the specific requirements and setup steps are as follows:

Required Hardware: 1) Microcast device (e.g., made by NetGear), or Intel Widi device;

2) The host needs to support wireless network cards.

Step 1) Turn on your microcast device and let it connect it with the monitor (HDMI port.

VGA interface);

3) After successful pairing, the screen of the host can be displayed on the display through wireless technology.

At present, the computer host and the monitor cannot be connected wirelessly, and the signal can only be transmitted through a wired data transmission cable.

About Computer Monitors and Consoles:

A computer monitor is also commonly referred to as a computer monitor or computer screen. It is the most important computer component in addition to CPU, motherboard, memory, power supply, keyboard, mouse, and is a display tool that displays certain electronic file information on the screen through a specific transmission device and then reflects it to the human eye.

At present, computer monitors are divided into two categories: LED display and liquid crystal display.

The main unit refers to the main part of the computer other than the input and output equipment. It is also used to place the mainframe of the main board and other major components. This typically includes CPU, memory, hard disks, optical drives, power supplies, and other input/output controllers and interfaces.

In network technology, it is about the terminal equipment that sends and receives information.

Just buy a wireless transceiver.

This technology is there.,Intel seems to be called ** center.,I haven't seen it for sale.。 Look for it.

Is this okay? I haven't seen it yet.

Because people operate the computer next to the host,1The general display is not too far away,So,1In general, there is no need for wireless connectionEven if you use a TV as a monitor,There will be a wired mouse and keyboard,So although the wireless connection between the host and the monitor is theoretically simple,But it is not necessary Although with the development of science and technology,1It is possible to view the original post"

Characteristics of the development of preschool children's observational ability:

1) In terms of purpose, because the nervous system is not developed enough, children tend to observe as they like, are easily affected by irrelevant things and details, and are very likely to be attracted by the objects they like and are interested in. Children aged 3 to 4 years generally forget about the observation task during the observation process, and the purpose of observation in children aged 4 to 6 years is improved.

2) in terms of duration, it was affected by children's preference for observed objects, but improved slightly with age; In an experiment, the observation time of three or four-year-old children was only 6 minutes and 8 seconds, which increased to 7 minutes and 6 seconds at the age of 5 and 12 minutes and 3 seconds at the age of 6.

3) Systematically, children are not good at connecting the whole object of observation with the part, and between the part, and can only get a single part of the observation; Children's observation gradually develops from the initial chaos to an organized, systematic and comprehensive perceptual process.

Why do you do that? ~

How to connect the host to the monitor:

1. Prepare an HDMI cable.

2. There are two areas on the host: "on-board interface area" and "independent graphics card interface area", and the "independent graphics card interface area" is preferred, and the independent graphics card is clearer than the on-board transmission screen.

<>3. After finding the HDMI interface in the "Independent Graphics Card Interface Area", connect one end of the HDMI cable.

4. The other end is connected to the HDMI interface of the monitor.

There is a special cable for connecting the computer host to the monitor, and you can connect the two heads directly to the monitor and the host.

How to connect the computer host to the monitor, the computer host has a wire jack directly connected to the wire connection jack has a jack, and you will not be able to plug it in if the mouth is wrong.

In this regard, it must be noted that in general, most of the hosts are connected by wire, and a few are wireless.

Summary. Hello dear, how does the computer display realize the wireless connection with the host? The receiver of the wireless screen projector is connected to the display through the HDMI cable - after the wireless screen projector is powered on, the display screen should be the standby screen of the wireless screen projector (you can customize the settings);

2. Plug the HDMI transmitter of the wireless screen projector into the computer (you need to press it for the first time, and you don't need to press it later, the HDMI button is also known as the drive-free button); The computer screen should already appear on the monitor screen by this time.

Special statement:Projection through HDMI wireless screen projector point-to-point,No need to connect to the network,No software,No need for various settings,The disadvantage is that the transmission distance of point-to-point mode is generally within 15-20 meters,5G The limit distance in the frequency band can reach 30 meters (it can reach 50 meters in the frequency band,But because of the low transmission rate of the frequency band,Not used much)。

If there is wireless network coverage at home, then after the bridge, as long as the wireless coverage area is available, the screen can be projected wirelessly, so as to get rid of the limitation of distance.

Hello dear, how does the computer display realize the wireless connection with the host? The receiver of the wireless screen projector is connected to the display through the HDMI cable - after the wireless screen projector is powered on, the display screen should be the standby screen of the wireless screen projector (you can customize the settings); 2. Plug the HDMI transmitter of the wireless screen projector into the computer (you need to press it for the first time, and you don't need to press it for subsequent noise, and the HDMI button is also known as the drive-free button); The computer screen should already appear on the monitor screen by this time. Special Statement:

Projection through HDMI wireless screen projector point-to-point, no need to connect to the network, no software, and no need for various settings, the disadvantage is that the point-to-point transmission distance is generally within 15-20 meters, and the limit distance under the 5G frequency band can reach 30 meters (it can reach 50 meters under the frequency band, but because the frequency band transmission rate is low, it is not used much). awind Qiji wireless screen projector has a wireless bridging function (if you want to know about the bridging function, you can contact**technical or**customer service),If there is wireless network coverage at home,Then after the bridge,As long as the wireless coverage area is a few touches, you can wirelessly projection,So as to get rid of the limitation of distance。

1. Find the HDMI port on the chassis (it is recommended to choose the interface on the discrete graphics card first).

2. Use an HDMI cable and connect one end to the independent graphics card interface of the case.

3. Connect the HDMI port on the monitor at one end.

It's through the connecting cable, of course. It mainly depends on what interfaces the monitor has, and whether the computer motherboard supports these interfaces. There are several types of interfaces:

VGA, DVI, HDMI, DP, their display is that the latter one is better than the previous one. Nowadays, the general VGA interface of the machine is rare. The best one is the DP interface.

If the motherboard supports it, get a cable and connect it. Of course, if you have a cable that supports the transfer interface, you can also connect different interfaces, but it is not recommended, most of these cables cannot achieve the nominal effect.

3. Find the memory module, take out the double-sided and wipe it carefully. Carefully remove the dust from it, smudge and put it back in the memory slot (note the direction).

4. Put it back is to clamp the memory module tightly, and carefully check whether it is stuck in place. After checking, close the lid of the case and try to plug it in.

5. Sometimes it can also be the reason on the hard disk. The solution is to unplug the hard drive cable and plug it in again after a while. If none of the above methods work, consider finding a repair shop.

Ask why no appears on the monitor

Why does no appear on the monitor

Ask a question oh on.

Oh on oh thank you.

You're welcome, please give a thumbs up.

There is a connecting line, just connect it.

1. Connect the VGA cable on the monitor first, and fix the two screw DAO wires behind the DU after connecting it. The fixation is mainly due to the concern that the connecting shu line will fall off when moving.

2. Then connect the other end of the VGA cable to the computer host.

3. Next, connect the power cord to the monitor, (note that you only want to connect it to the monitor, don't connect the socket at the other end of the power cord, and then turn on the power after all the connections are completed.) )

4. Next, connect the mouse to the host.

5. Connect the keyboard as well. (The green is the mouse, and the purple is the keyboard.) At the same time, pay attention to the internal pins of the mouse and keyboard plugs, which should be aligned with the position of the pinholes in the interface before insertion.

Terminate one network cable to the RJ45 port of the host computer, and then the other end to a switch or router or modem.

6. Next, connect the power cord of the host.

7. Next, you can connect the power plugs of the host and the monitor to the socket to power on the host and the monitor. It can be turned on and used normally.

Miracast certified devices that support WiFi Display, can be transmitted via WiFi. Take the ASUS zenfone3 phone connected to the FX73VD laptop as an example.

1. Connect the laptop to the WiFi network (press the Window + P shortcut key and click "Connect to wireless monitor", select "Project to this computer"). Pay attention to the "computer name", which in this case is "desktop-ag6fuf3". The phone is connected to the same wifi network that the laptop is connected to, and on the phone, go to "Settings" - More - --play to".

2. Select the name of the computer, here it is "desktop-ag6fuf3".

3. A prompt of "whether to allow the mobile phone to project here" appears on the notebook, select "Yes", and the prompt "The mobile phone is about to be projected". The mobile phone prompts "Connecting", and after success, it prompts that it is connected. At this point, the phone screen can be displayed on the notebook.

Move the mouse to the top of the screen to adjust the size of the phone display and the turn off button.

The computer connects wirelessly to a TV, projector, other computer, or other type of external display that supports Miracast.

win11 system.

Method 1: <>

2.Tap the wireless display you want to connect to and <>

Please click Enter a description.

3.Connecting, waiting for the automatic connection to succeed.

Please click Enter a description.

Method 2: 1, open the system [Settings] - Bluetooth and other devices - Add device] <>

Please click Enter a description.

2 Tap Wireless Display or Docking Station

Please click Enter a description.

3.Tap on the wireless display you want to connect to, and it will connect automatically.

Please click Enter a description.

1. Connect the VGA cable to the monitor first, and fix the two screws at the back after connecting. The main reason for fixing is that the connection line will fall off when it is moved.

2. Then connect the other end of the VGA cable to the computer host.

3. Next, connect the power cord to the monitor, note that you only want to connect it to the monitor, and don't connect the other end of the power cord to the socket first, and then power on after all the connections are completed.