What should I do to solve the problem of water in my mobile phone? It s Apple 8p

How to deal with the water after the iPhone is ingressive.

1.Turn off the phone as soon as possible, cut off the power, and do not try to turn it on again to avoid causing a short circuit in the motherboard.

2.Remove the SIM card and use a tissue or cloth to remove water from the outside and crevices of the phone.

3.If there is light water ingress, you can wrap the phone with a paper towel, put it in a bag and put it in a small bag of desiccant.

4.The mobile phone cannot be turned on after entering the water, most of the chips such as the motherboard and CPU are short-circuited and burned, and it is recommended to send it to the after-sales service center for repair immediately.

Don't try the following wrong methods after your phone gets into water.

1.Don't shake your phone too hard. Because under the constant shaking, the liquid will swim inside the machine, and the moisture may enter deeper and burn the internal chip of the machine.

2.Don't use the hot air of a hair dryer to dry your phone for a long time. iPhones are now all metal bodies, and metal conducts heat easily, which will blow off the solder joints of the motherboard inside the machine, causing the motherboard to malfunction.

3.Do not attempt to charge a phone that has been flooded. An iPhone that gets into the water may have water stains inside, which can burn out the motherboard when it is powered on and cause a more serious failure.

4.Do not leave your phone in water for a long time. In the case that it cannot be used normally after two or three days after general treatment, it should be sent for repair immediately, and long-term placement will cause the motherboard to be corroded, or even unable to be repaired.

What to do if the iPhone gets into the water:

Do not try to turn on the machine immediately after water ingress. Once you try to boot it, it will increase the area burned out by the motherboard by short circuit.

2.Don't shake your iPhone. If you shake your iPhone, water will flow and water may expand inside your iPhone.

3.Clean the water ingress area in order, quickly remove the SIM card, and wipe the water in the iPhone shell, dock interface, and SIM card slot.

4.Do not turn on the machine immediately after absorbing or wiping off the water. It is essential for a professional to clean the moisture of each chip of the internal motherboard.

5.Most of the time when water enters and the computer cannot be turned on is due to a short circuit of the motherboard power supply, CPU, hard disk and other chips. The motherboard needs to be repaired.

6.Contact a repair center for inspection and repair.

1.Do not try to turn on the device immediately if there is water ingress. Because the iPhone has a built-in battery that cannot be removed, the motherboard will be short-circuited if it gets into the water, and if it is turned on, the motherboard will be burned, causing irreparable consequences.

2.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

3.Wipe down the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

4.Send it to a repair center for repair as soon as possible. If the motherboard is severely corroded over time, it will cause irreparable consequences.

There are two regular Apple after-sales services in Chongqing.

In the case of ignorance, it is not recommended to disassemble the machine by yourself and repair it blindly. So as not to cause unnecessary secondary damage to the phone.

To repair the mobile phone, it is necessary to go to the regular Apple after-sales service for repair, so that it can be guaranteed.

Chongqing Jiangbei Guanyin Bridge Maoye Oriental Times 3201

Chongqing Shapingba Wangfujing Department Store Block B, 2706

Many people have the trouble of getting into the water on their iPhones, and most of them don't have much of a problem when they just fall into the water. However, if it is immersed in water for a long time, it can cause many problems. Here are some effective solutions for you.

The first thing is to take out the iPhone in time, and immediately wipe the water on the surface, and then force it to shut down. If necessary, remove things like the case of the phone, otherwise it will interfere with the subsequent drying process.

After the first step is completed, be sure to dry the iPhone thoroughly, especially pay attention to the power button, volume button and headphone port and other parts that are not easy to notice, you can use a cotton swab or something similar to carefully wipe it clean, and make sure that all parts are very dry.

Of course, this is not enough, but also to dry the Apple phone thoroughly, you can use methods such as hair dryer and rice cylinder drying method. Be careful to blow in all directions, but also keep a certain distance, and remember not to blow in the same place for too long.

Another way is to bury the iPhone in a rice bowl, if there is no rice bowl at home, find a bag that can be sealed, and then fill some rice to bury the iPhone. After putting it in the rice, wait until the phone is dry, which will take at least a day and a half. At the same time, you must be careful not to let broken rice grains enter the earphone port and other parts of the Apple mobile phone.

If neither of these methods can be used, natural drying can sometimes help. If you use the above methods, the mobile phone still can't turn on or has other problems, you still have to take it to a professional mobile phone repair shop to repair it in time.

1. Divide the situation into three types, fall into clean water when the power is on, and fall into the non-corrosive liquid in the case of power off.

2. Drop into non-clean water when energized, or corrosive liquid, viscous liquid or other unclean liquid regardless of whether it is energized or not.

3. First of all, for the first two situations, do not think that the machine has been scrapped, and fall into the water in the case of power-on, this situation generally does not need to be dismantled, cut off the power as soon as possible, and shake it dry, but don't throw the machine off.

4. In the case of power failure, if you fall into a non-corrosive liquid, you can basically determine that the machine is not damaged, but the LCD screen may be ugly, and it can be sent to the nearest maintenance department for processing or automatically dismantling the machine for cleaning.

In this case, first wipe the water with toilet paper, and then go to the repair point to repair it, because you have already disassembled the phone yourself, so the officially authorized repair point will not repair it.

After the mobile phone is forced to shut down, disassemble all parts, clean up all the water first, and then place it in a ventilated place for 24 hours, and finally turn it on, don't turn it on immediately, it is easy to short circuit, I hope it can help you.

Dry it first, see if you can still use it, if you can't use it, there is no way, it should be repaired, but this old machine, buying a second-hand one should be more valuable than repairing.

The screen of the Apple mobile phone is bright and dark at the same time, small components are replaced, and the yin and yang screen of the iPhone is repaired in seconds.

If the mobile phone is in water, what should I do, if the mobile phone is in water, take it out, use a hair dryer to dry the water in the mobile phone, and see if it can still be used.

1. First of all, take the mobile phone out of the water in time, and turn it off as soon as you pick it up, if you don't turn it off, it will form a vortex current, and the light one will burn out the screen battery, and the heavy one will directly burn off the motherboard. Then use a towel or paper towel to wipe off the water off the phone case. Quickly unplug the SIM card and store it somewhere else.

Next, use a paper towel to suck up the water from the headphones, dock and SIM card slots. Don't shake. Be aware of the tiny places;

2. The second is thorough drying, which can be done by using electric hair dryers or rice cylinders;

3. If the above methods do not work, it is best to send them to the mobile phone repair shop in time and hand them over to professionals to repair.

What to do with an Apple 8 phone that has been flooded? Can it still be used?

What to do with an Apple 8 phone that has been flooded? Can it still be used? Hello!

Pro+Answer 1 The first thing is to get out of the water quickly and turn it off. 2 Remove the mobile phone accessory case and earphones. 3 Take out the SIM card of your phone and wrap it in a tissue.

4 Use a dry paper towel or cloth to wipe the surface and crevices of the machine clean. 5 Use the self-defibrillating wind position of the hair dryer to blow on the iPhone headphone jack, earpiece, power port, and SIM card for about ten minutes. After the above treatment, try to turn on the machine after leaving it for about 1 hour to see if the function is normal.

If it has been soaked in water and the phone has been automatically turned off, it is recommended to send it to the after-sales repair center immediately for cleaning.

After the apple hand slag machine is flooded, as long as the function is still normal, it can be used, but once the pants are opened, the cover mold is noisy and simple, and the moisture inside is dry, otherwise it will cause continuous damage.