My oxygen concentrator is not gassing, what s going on?

Is the machine normal but out of gas?

I don't know.

Common causes. 1. After pressing the power supply, the oxygen generator will continuously beep to alarm, and there will be no air flow at the oxygen outlet. Causes:

The power plug falls off; damage to the electrical outlet; The circuit board of the oxygen concentrator is damaged; The fuse blows. Solution: Check whether the power cord plug is plugged in properly; Check whether the indoor power supply is energized; Contact after-sales maintenance personnel; Replace the fuse or circuit board;

Common faults. 2. The oxygen concentrator will automatically shut down after a while of normal operation: possible causes:

The cooling fan is not working; The solution to the obstruction of the bottom exhaust port: check whether the bottom exhaust port is unobstructed, and turn on the oxygen generator in a spacious and cool place for an hour or two to exclude it.

Common faults of Inwellcom oxygen concentrator.

3. Turn on the switch of the oxygen generator when the power is turned on, there is no air flow, and there is no working noise of the compressor. Cause of failure: The starting capacitor of the oxygen concentrator is damaged, which is usually caused by too long service life or unstable voltage. For solutions, please contact Lianying Weikang professional after-sales maintenance personnel;

Common faults of Inwellcom oxygen concentrator.

Fourth, the start-up works normally, but after about five minutes, the oxygen concentrator has a red light alarm accompanied by a buzzer, and the flowmeter cannot adjust the flow rate. Cause of failure: The oxygen outlet in the humidification cup is blocked by limescale or the oxygen intake pipe is dead and the oxygen from the oxygen generator cannot be eliminated, resulting in excessive pressure, and the compressor overpressure protection alarm and shutdown.

Exclusion method: soak the humidified cup with white vinegar for half an hour, remove the scale of the oxygen mouth, and replace the new oxygen inhalation tube to check and remove the dead fold;

Household oxygen concentrators do not produce oxygen, hello! Reasons why the household oxygen concentrator does not produce oxygen: (1) The oxygen outlet is blocked.

Check whether the oxygen outlet of the oxygen generator, humidification bottle, and the pipeline of the oxygen inhalation tube are unblocked. Check whether there is airflow at the outlet of the oxygen concentrator, if there is any, it means that the oxygen inhalation tube or humidification bottle is blocked. (2) The air inlet is blocked.

The air inlet of the oxygen concentrator is generally at the back of the machine, and it is required to leave the wall more than 20 cm to ensure that there are no towels or foreign objects blocking the oxygen outlet. (3) Molecular sieve damage. Too much dust or humidity in the air can cause damage to the molecular sieve.

If the oxygen concentrator does not produce oxygen, it may be that the pipeline of the oxygen concentrator is blocked, at this time, as long as the pipeline is taken down for inspection, if the oxygen concentrator itself does not produce oxygen, it may be that there is a fault inside the oxygen concentrator, and it should be sent to the manufacturer for maintenance, or please ask a professional maintenance master to come to the door to actually see how to repair it, hoping to help you.

If the oxygen concentrator does not produce oxygen, it may be due to the following reasons:1Clogged strainer:

The filter screen of the oxygen concentrator needs to be cleaned or replaced during the bending and drying period, if the filter screen is blocked, the oxygen cannot pass through, resulting in the oxygen concentrator not producing oxygen. 2.Low oxygen concentration:

The oxygen concentration of the oxygen concentrator needs to be up to a certain standard, and if the concentration is lower than the standard, it may be due to a leak in the oxygen or a malfunction in the oxygen generator. 3.Power failure:

Oxygen concentrators require a stable power supply**, and if the power supply fails, the oxygen concentrator may not work properly. If the oxygen concentrator does not produce oxygen, you can try the following methods to repair it:1

Cleaning or replacing the filter: Take out the filter of the oxygen concentrator, wash or replace it, and then reinstall it. 2.

Check the oxygen concentration: Use the oxygen concentration detector to check whether the oxygen concentration of the oxygen concentrator meets the standard, if the concentration is lower than the standard, you need to check whether the oxygen generator is working properly. 3.

Check the buried hole of the power supply: check whether the power supply of the oxygen concentrator is normal, if the power supply fails, it needs to be repaired or replaced. If the above methods do not solve the problem, it is recommended to contact the after-sales service center of the oxygen concentrator for maintenance.

When the oxygen concentrator is started, the gas does not come up, indicating that there is a problem with the oxygen concentrator inside.

First: there is a problem with the compressor.

The compressor is one of the core components of the oxygen generator, and if there is a displacement or the compressor power is insufficient in the process of use, the gas will not come up.

The second type: there is a problem with the air connection pipe inside the machine.

The inside of the oxygen generator is mainly the transmission of gas, and when the gas pipe is loose or falls, there will be a situation where the gas cannot come up.

The third type: the humidification cup of the oxygen concentrator is not sealed.

When the oxygen concentrator is working in the process of external oxygen, the sealing ring and other parts of the humidification cup are not sealed, then the produced oxygen will leak out from other places, which will also lead to the occurrence of the said situation. Generally, the life of the oxygen concentrator is a certain amount of time, not to mention two or three years, so it is difficult to say that there will not be any failures in the process of use, so it is very important to get good after-sales service when you buy, so what should I do if the Yuyue oxygen concentrator has no deflation sound? What should I do if I encounter a fault?

Yuyue oxygen generator adopts the principle of physical oxygen production, through the pressure swing adsorption effect of molecular sieve, directly separates oxygen and nitrogen in the air at room temperature, extracts high-purity medical oxygen, and realizes continuous and uninterrupted oxygen supply. Generally, connect the humidification bottle (please inject an appropriate amount of pure water according to the instructions of the instructions) and the oxygen inhalation tube, turn on the power, and you can get high-purity pure oxygen within 1-2 minutes. If required, this oxygen concentrator can continuously supply high-purity oxygen for a long time.

What should I do if the water from the household oxygen concentrator does not come out of the airHello dear, reason 1: The lid of the humidification bottle is not envied and tightened, and there is air leakage Elimination method: Turn on the power switch of the oxygen concentrator and adjust the flow meter to 3 liters.

Use your hands to block the oxygen outlet end of the humidification bottle. The flowmeter float should move downwards while the humidifier makes a sizzling sound. Otherwise, the humidifier is leaking.

Tighten or replace the humidification bottle with a new one. Reason 2: Elimination method of opening the safety valve of the oxygen concentrator:

Pick up the humidification bottle of the oxygen generator, shake it slightly, and then close the safety valve on the cap of the humidification bottle. Reason 3: There is a problem with the oxygen inhalation tube or other oxygen insufficiency parts

Check if anything is clogged, clean or replace with new parts. Reason 4: The filter accessories have not been cleaned for a long time, and the replacement and exclusion method:

It is recommended that the oxygen concentrator be cleaned every 200 hours of work; Filter cloth and filter are recommended to be cleaned in time every 900 hours of work. If the filter of the oxygen concentrator is not cleaned and replaced for a long time, the air cannot enter the oxygen concentrator, and the output volume will naturally become smaller. Clean or replace the filter fittings in a timely manner.

Reason 5: The flowmeter knob is damaged Elimination method: The machine is running but there is no oxygen output, the flowmeter float is at the bottom or somewhere, and the flowmeter knob is adjusted and does not move.

This may be due to a clogged tube inside the humidification bottle or a damaged flow meter knob. 1. Turn on the power switch of the oxygen machine to make the machine run. Unscrew the humidification bottle to see if the float of the flowmeter is adjustable, if it is adjustable, the tube in the humidification bottle is blocked, and it can be dredged.

Instead, check the flow meter knob. 2. Rotate the flowmeter knob counterclockwise to see if the flowmeter knob rod rotates, if not, the flowmeter knob is damaged. It is recommended to contact an after-sales engineer to replace or repair the flow meter.

Hope it helps. If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!