Why do you jump over the floor gate as soon as you use the machine at home?

As soon as the electrical appliances are used in the home, the main switch gate on the floor will be jumped, which must be caused by a short circuit or leakage of the wiring or an electrical appliance at home.

The first situation is that the electrical circuit in the household is damaged, when the electricity consumption exceeds a certain value, it exceeds the leakage current value of the resident's circuit breaker, and the household circuit breaker does not have time to trip, crosses the first-level protection, and reaches the leakage current value of the unit layer circuit breaker.

There is also a situation that when designing the circuit, the household circuit breaker is not equipped with leakage protection (old houses and old communities), and the electrical equipment has hidden dangers, and the grounding wire is not used (or the socket is not used grounding protection), which crosses the first-level protection and causes the second-level protection to trip directly.

If you use a machine at home, you can jump the floor switch, indicating which wire in your home has grounding, or the decorator's machine. There is a phenomenon of grounding, and there may be something wrong with that machine.

The power of the machine is large, and the total power consumption has exceeded the rated power of the main switch of your home appliance meter.

It should be that the power consumption is too large, the power consumption of the whole floor is too large, and all kinds of breakfast and dinner are gathered together, so it will cause tripping.

Because the starting current of the machine is large, the air switch and load current are small, so it will trip.

This means that your store is overloaded. The power is relatively large, so it trips as soon as it is used.

It means that the electrical appliances in your home are too powerful, or they are running out of steam.

The aunt rate of the machine has exceeded the compliance of the meter.

Questions about biology in high school. Which is active transport Personally, cellular respiration here refers to the normal metabolism of cells.

The main switch at home does not jump, and the total switch downstairs trips old.

Dear, hello, I'm glad to answer for you: the main switch at home does not trip Zen, and the total switch downstairs trips? A:

1. Check the electricity meter. Observe whether the electricity consumption of the meter corresponds to the recent electricity consumption at home. If it is correct, it should be the problem of the air switch.

If it doesn't, it may be an overload trip caused by line leakage. In this case, it is more troublesome. 2.

If it's a problem with the air switch, it may be that the thermal expansion sheet inside is broken. Of course, just change it to another one. 3.

If the air switch is fine, you should consider whether the wiring at home is dusty (it will definitely be replaced after more than ten years.) Just replace the aging wiring. 4.

Observe whether the meter is metering when the electricity is not used at home (when the air switch is closed). 5.If the meter is constantly metering, there must be a leakage somewhere.

If there is still a problem with the aging line. You'll have to hire an electrician. I hope mine can help you, I wish you a happy life, if mine is helpful to you please give me a 5 star praise Oh, thank you for your support to me.

The main switch at home does not jump, and the total switch downstairs trips old.

1. Check the electricity meter. Observe whether the electricity consumption of the meter corresponds to the recent electricity consumption at home. If it is correct, it should be the problem of the air switch.

If it doesn't, it may be an overload trip caused by line leakage. This situation is more troublesome and repentant. 2.

If it's a problem with the air switch, it may be that the thermal expansion sheet inside is broken. Of course, just change it to another one. 3.

If the air switch is fine, it is necessary to consider whether the wiring at home is aging (it must be replaced after more than ten years.) Just replace the aging wiring. 4.

Observe whether the electricity consumption meter is being metered when the home is not using electricity (the air switch is closed). 5.If the meter is constantly metering, there must be a leakage somewhere.

If there is still a problem with the aging line.

Now there are more and more household appliances, modern society can not do without electricity, the whole building is always tripped, that is, the circuit load is too much, more than the rated power of the circuit, the circuit automatically protects the tripping, since you know that there is a problem with a line, directly trip the main gate, three units share a main gate is the problem, it is recommended to contact the electric power department, separate the main gate for three units, each unit a switch, so that the three units will not affect each other, greatly reduce the probability of tripping! At the same time, during the peak period of electricity consumption, reduce the simultaneous use of electrical appliances, such as air conditioners, washing machines, and water heaters can be used at the wrong time, try to use them at the wrong time, reduce the power consumption, and hope to solve the problem as soon as possible!

It is because the power consumption is overloaded and it trips, and the tripping problem can be solved by replacing it with a large-capacity transformer.

Call the property to inspect it, it always trips large or small, and it is the main gate.

Don't worry ! Appliances are designed with nothing in mind that they won't break.

1. You can gradually plug in or open the electrical appliances, when you turn on a certain electrical appliance and trip, you must first check whether there is a suspicion of leakage in this piece, or a high-power electrical appliance, and the load has accumulated to exceed the rated load.

2. Check whether there is leakage to turn off or unplug other electrical appliances, turn on this one separately, if it is turned on normally, it means that it does not leak, if it will also trip, it means that the problem is on this equipment.

3. Because the heavy load exceeds the rated load, it belongs to the overload protection tripping.

If you don't understand, it's safer to find a professional, after all, electricity is a very dangerous product.

The whole building always trips and suspects that sometimes the owner uses the shield to overload the electric load caused by the block, it is recommended to monitor the current of each phase at the main switch, and then further improve it according to the situation. Reeds and Hu.

The whole building always trips, and I can't find the reason, how to deal with it? I think that if the whole building is always tripping, this should go to the power department. The electric power department directly calls the service**, but it can be said that you can directly go to the door to find out the reason.

Now there are more and more household electric finch height finders, modern society can not do without electricity, the whole building is always tripped, that is, the circuit load is too much, more than the rated power of the circuit, the circuit automatic protective tripping, since the leakage of the road a line has a problem, directly trip the main gate, three units of the common one main gate is the problem, it is recommended to contact the power department, separate the main gate for three units, each unit a switch, so that the three units will not affect each other, greatly reduce the probability of tripping! At the same time, during the peak period of electricity consumption, reduce the simultaneous use of electrical appliances, such as air conditioners, washing machines, and water heaters, and use them at the wrong time as much as possible, reduce the power of electricity, and hope to solve the problem as soon as possible!

Turn off all the power, open the gates, and try to open the gates again?