What is the effect of poor contact between the motherboard and the chassis, and the cable on the pan

It still costs money! The back plate of your case is uneven and deformed, and after the motherboard is installed, the motherboard is also deformed, so there is a failure, so change the case!

Yes! The first time I heard that the chassis was in poor contact with the motherboard. Khan died.

If you say that the contact is poor, you should change the chassis, not the motherboard!

Besides, you can disassemble the computer, use a stack of paper to pad the bottom, and then put the motherboard up, and then try to see if this happens.

The most common common problem with frequent reboots is the motherboard and memory, if you have two RAM, try to split one of them, try, try both separately to see if it is a memory problem.

It's because your case is of poor quality that your motherboard is deformed. This is quite normal, and the garbage box will be bought less in the future. Also, don't take the word of the profiteer.

Bad motherboards for them, they can all sell for money!! Let's go change the main chassis, *** order. 200 quick money, don't feel that you can't get it.

Then run naked to the computer!!

My computer doesn't have a case, the motherboard is just on top of a book,,, other stuff is left around

Put the old computer right, and use it

You can change the chassis and you're good to go

Why add 80 yuan to change a motherboard for you?

If you repair your motherboard, he can sell it, or maybe you can sell it without repairing it, and make money, and that's it

It's not that you haven't installed the motherboard, so remove it and put the motherboard flat and install it again. Remember not to tighten the screws too tightly.

The motherboard case panel cable is plugged into the motherboard without much effect, usually the power button is pressed and the host is not powered on.

1. First find the cable of the case.

2. Find the F-Panel interface on the motherboard, and insert the cable into the corresponding pin according to the logo on the motherboard.

The front and rear audio interfaces of the motherboard and chassis do not match at all.

It's normal. If you buy a motherboard, you should get a metal bezel, and you have to combine it with this metal bezel and remove the original metal bezel.

In this case, there should be no compatibility, since each bezel is corresponding to the motherboard, independent of the chassis.

Give a**, this is the thing.

My current computer,The main accessories were equipped last year.,The chassis is 02 years.,It's early enough.,It's also ready to be installed.。

The old chassis is the old version, and now it is the new version.

Send it to the computer store, where there is a master who can help you put it on.

First of all, constantly pressing the computer switch will cause the computer motherboard to break, but this is relatively rare. What is more likely to break is the hard drive, power supply, and so on.

First, the hard disk is the most vulnerable to breakage in this situation. Because when the hard disk is working normally, the speed is 5400rpm and 7200rpm, and the sudden power off is most likely to cause the hard disk to break.

Second, in this case, the power supply will also cause, with the increase of the current on and off, the temperature will be too high, and then burn out.

Third, the motherboard will naturally be damaged. Because of frequent power on/off, it will cause the current to increase, the temperature is too high and damaged.

Fourth, in fact, all electrical equipment will cause damage to this high temperature.

No, poor contact will not cause high current to pass through the motherboard, so it will not burn out.

Whether the gold finger is worn, or the heat dissipation problem causes the circuit to be unstable.

Hello: 1. The motherboard is fixed on the chassis, and the fixing screws have two ends: one is fixed on the chassis, and the motherboard is fixed on the screwsThere will be no damage to the chassisof.

2. If the screws near the rear of the chassis are not tightened or loosened, they may shake when inserting each interface, but they have little impact.

First, check whether the various lines are plugged in, whether they are plugged in, and plug them in again.

And exclude whether all kinds of accessories are not in good contact, such as CPU, memory module, graphics card, hard disk, etc., all that can be plugged and unplugged are re-plugged.

Check whether the solder joints on the back of the motherboard are short-circuited to the chassis.

Then turn it on and try it.