-
Anonymous users2024-02-07The surface of the transmission electric drum can be covered and engraved with a diamond pattern, which can effectively increase the friction of the drum and prevent the conveyor belt from deviating.
-
Anonymous users2024-02-06Adjust the spacing between rollers.
-
Anonymous users2024-02-053. All 1, install a deviation adjustment device - a self-aligning idler set, on which there are two small stop rollers, see the figure below;
2. The tail reversing drum can be made into a drum in the shape of a drum, which is conducive to deviation adjustment.
-
Anonymous users2024-02-04Conveyor belts often deviate during the working process, and at this time, we need to deal with it and adjust the conveyor belt. So, how do we prevent the phenomenon of conveyor belt misalignment in the work of the conveyor belt?
1. When the conveyor belt occupies water, it is easy to deviate. In the process of using the conveyor belt, we should try to avoid the contact between the conveyor belt and water, and try not to let the conveyor belt work in the open air, so as not to damage the conveyor belt in rainy days. Do not leave water in a place where the conveyor belt is working to prevent accidental spilling of water onto the conveyor belt.
Second, the conveyor belt can be too long and too large, and the roller is matched, which is easy to slip and deviate when working. How to prevent this kind of slippage and mistracking? You can do some special processing for positioning when the conveyor belt and the roller are matched, such as processing on the conveyor belt, making a guide bar, as a guide for positioning, of course, there must also be a groove, the groove is just matched with the guide bar of the conveyor belt, and the fixed conveyor belt is guided, so that the conveyor belt will not slip and deviate from the left and right.
Third, the reason for the deviation and slippage of the conveyor belt is also because it is not installed well in the installation process and the drum is not debugged. Therefore, when installing the machine, the conveyor belt and the roller are adjusted so that they are exactly matched.
Fourth, the conveyor belt has been used for a long time, the roller will be loose, and after a long time, the conveyor belt may also be stretched out due to the tensile force, resulting in slippage and deviation. To prevent such slippage and deviation, we need to check and maintain the machinery in time, and adjust it in time if it is loose, and the position of the roller can be adjusted, and our loose conveyor belt can be tightened. (From the official website of Guangzhou Qingchuan).
-
Anonymous users2024-02-031. The quality of all conveyor belts is not good, and the two sides are not parallel (and asymmetrical with the longitudinal centerline of the conveyor belt) to form a periodic wavy shape, which causes the conveyor belt to deviate periodically; The conveyor belt joint is not good, and the cutting edge of the conveyor belt joint, that is, the joint surface, is not perpendicular to the longitudinal center line of the conveyor belt, resulting in the formation of a certain angle between the two sections of the conveyor belt, which should be a straight line, which will cause the conveyor belt to deviate. So how do we solve this problem? Huayun rubber **** will explain to you how to make the conveyor belt not deviate.
In the first case, if the quality of the conveyor belt is too poor or the conveyor belt is refurbished, if the user thinks that it can be used, adjust the joints, rollers and rollers to minimize the amount of mistracking, and increase the self-aligning idlers and anti-mistracking rollers.
For the second case, redo the belt joint; The situation of conveyor belt deviation is not only the above two situations, the specific causes of deviation are very complex, and the specific analysis should be treated, in short, the deviation should be distinguished from the head, tail, intermediate fuselage or bearing surface conveyor belt, return conveyor belt deviation, and the adjustment direction of the roller and idler should be adjusted purposefully to reduce or eliminate the deviation.
-
Anonymous users2024-02-02Hello, check the individual rounds, in a line?
What is a misunderstanding of thinking: In fact, there is a difference between misunderstanding and wrong thinking, and misunderstanding is actually a very systematic mistake in thinking, or a group of wrong thinking. In other words, misunderstandings in thinking can withstand scrutiny, and the most important characteristic of misunderstandings in thinking is to draw correct and rigorous conclusions according to a certain pattern. >>>More
I have never assembled a gear before, today I consulted some others, and roughly learned the method as follows: the first step, the gear end face alignment of the second step, showing the indexing circular surface of the gear, use it to add the tangent relationship of the third step, if the tooth shape interference is to use the gear's own default datum, cooperate with each other to ensure that the gear does not interfere, after this step is done, this constraint should be suppressed and then use the indexing circular surface to carry out gear relationship assembly, the assembly relationship will automatically help you find the correct transmission ratio, Right-click to confirm the end of the gear assembly relationship, if the set is out of order, the relationship is uninhibited, and the gear will be restored to its original state. I did a GIF animation tutorial with SolidEdge ST **Way 1:
1. Fill the laundry sink with water, or use the "drum cleaning" function of the washing machine, add 1 cup (about 100 120 grams) of baking soda, let the washing machine stir for 3 5 minutes, let it soak for 30 minutes, and then put the water off after 1 hour. Then wash it again with the normal cleaning procedure. >>>More
This is done by modifying their ciphertext as needed along the way, so that neither A nor B knows that they are sharing communication with C. >>>More
By improving performance management, the motivation of pay-for-performance can be improved. Here are some suggestions: >>>More