-
Anonymous users2024-02-07It is also possible that the hardware temperature is too high and the ...... is caused by it
Now is the summer to pay attention, especially to clean the dust in the CPU fan.
-
Anonymous users2024-02-06If it's too hot, take care to cool down.
-
Anonymous users2024-02-05The voltage is not stable, or the plug is not plugged in properly, and this is only a small reason.
-
Anonymous users2024-02-041) Reinstall the operating system first, don't install software, patches, drivers, etc., and see if there is still a problem with booting? If you don't install drivers, patches, and software step by step, and find something that isn't suitable, don't install it.
Please note: If you restore the system or reinstall it, when installing drivers, patches, software and other things, be sure not to install the things that affect your accident this time, otherwise it will be restored or reinstalled in vain.
2) If it is caused by hardware problems, it is recommended to overhaul it.
-
Anonymous users2024-02-03Boot card windows welcome login interface.
1. Caused by a drive conflict, press F8 to enter the safe mode when booting up, if you can enter the safe mode normally, it is caused by the drive conflict. Think about what software you have installed, drivers, updates that are caused by patches, and uninstall them in safe mode.
2. Caused by poor contact of the hard disk. Open the case and re-seat the hard disk, connect the dual-wire hard disk to the motherboard interface, and replace one.
3. The hard disk has bad sectors or the MBR of the main boot is damaged.
Open the partition tool Disk Genius in PE, select the hard disk with the right mouse button, and click Bad Sectors Detection and Repair.
Select the hard disk with the right mouse button and click Rebuild Master Boot Record MBR.
Go back to the PE desktop and click on Windows Boot Repair, and select C drive to repair.
-
Anonymous users2024-02-02Please further upload the reboot screen** so that others can suggest a more reasonable solution!!
-
Anonymous users2024-02-01FYI:
oem7grub 2009。。How to solve the problem that it cannot be turned on.
-
Anonymous users2024-01-31This has nothing to do with temperature......There is always a common problem of automatic restart is that some small files conflict, it is recommended to change to a pure XP (SP3) system, which is the most compatible ......
-
Anonymous users2024-01-301: Open the case to see if the CPU fan speed is normal, clean it up if it is not normal, and try it [add some silicone if conditions allow].
2: Check whether the power supply fan is rotating, it is recommended to change the power supply if it does not rotate.
-
Anonymous users2024-01-29Just unplug the memory module and wipe it well.
-
Anonymous users2024-01-28Let's see if the fan is running well, the one above the CPU, whether it can effectively dissipate heat, if it's good, it depends on the hardware problem, which needs to be tested on site. Thank you and good luck.
-
Anonymous users2024-01-27If it's not a virus and a fever, consider the hardware.
-
Anonymous users2024-01-26First of all, the first question you should see if your computer is too hot, which is the most likely cause of restarting, and the second is a virus, it is recommended that you do a comprehensive antivirus.
-
Anonymous users2024-01-25Either it's a virus, it's a hacker, it's a fan problem, or it's time for the motherboard to be replaced.
The computer power supply is poor, coupled with the unstable power supply of the mains, especially during the peak period, the number of restarts will be frequent, it is recommended to replace the computer power supply, or buy UPS.
Hehe, I've been in this situation too. Mine is also the s60v3 version. It should be the following cases: >>>More
Rebooting or shutting down for no reason, generally the CPU is too hot, viruses, dust, bad power supply, bad memory, too hot graphics card, and bad motherboard capacitors. >>>More
Don't be afraid that it's just a partition table error!
Hard disk MBR (Hard Disk Master Boot Record) and Hard Disk Partition Table Introduction Hard disk MBR is what we often call "Hard Disk Master Boot Record", simply put, it is a piece of data written in the absolute 0 sector of the hard disk by disk partition commands such as fdisk, it is composed of the main boot program, the hard disk partition table and the end of the sector flag word (55AA) These three parts, as follows: Components Number of bytes Contents and functions detailed description of the main boot area 446 Responsible for checking the hard disk partition table, Look for a bootable partition and be responsible for loading the bootable partition's boot sector (DBR) into memory; Hard disk partition table area 16x4=64 4 hard disk partition tables of 16 bytes each, which record the type, size, and location of each partition and the position where the partition starts and ends. The end sign block 2 always reads "55aa". The end of the flag area 2 is always "55AA", and the sum of the size of these 3 parts is exactly 512 bytes = 1 sector (each sector of the hard disk is fixed at 512 bytes), so people vividly call the MBR "hard disk master boot sector". >>>More
If the phone restarts automatically and the machine cannot be used normally, it may be a problem with the system or hardware of the phone, and it is recommended that you send the device to a Samsung service center for inspection. >>>More