Why can t the Crysis be installed!!

It's like this.,It takes at least 30 minutes.,If the machine is older or it's Pentium D,P4 or the like, it takes longer.,If it's an old machine.,I suggest you buy a genuine *** to DX9 version.,There are 8 patches inside.,You can play after installing it.,It's just that the effect isn't good.,At least it's guaranteed that it won't be carded.,If it's pirated.,Don't install it.,It's the same card to death when it's installed!My config is! Core 2 Duo E4500, ASUS P5K SE Master Edition, 320G HDD 8M Serial Port, *** Serial Port Burner, 800 Single 2G Memory, ASUS EN8800GT 512MB Graphics Card!

Power Huntkey 550W, 320G HDD serial port can be improved according to my configuration!Most players may be because of the version problem.,So card,I've seen a lot.,It's all configuration OK.,But it's still a card.,Please pay attention.,Is the power supply power enough?,The second is whether the version has played the XP system patch., !If the machine is enough,It's recommended to buy a genuine game.,There's 8 patches inside the genuine.,All of them won't return to the phenomenon of the card.,Use a good graphics card.,Just for a better effect.,In fact, the patch is based on the performance of the graphics card to improve the game.,As long as the patch is played,5200 cards can also be played.,Definitely not carded.,I've tried.,It's just that there's no so-called effect at all!

I'm also on the disc version, and I installed it for a full 6 hours, but it's troublesome! The installation method of the game belt I introduce to you Game Description:

1. Create a new folder in the hard disk, copy and paste all the files in the two *** discs into the folder (if there is a prompt of "whether to overwrite", you must select "Overwrite all"), and then install the game.

2. After the game is installed, copy and paste the files in the "crack" folder into the "Electronic Arts Crytek Crysis" directory of the game, and select Overwrite.

3. Run the game.

Sweat. You are very persevering and strong.

Let's configure your configuration.

Can't fit? It should be a problem with the plate.

I have to wait, my dish also has to wait, and if the machine is not good, I may have to wait for a long time.

Hello, I'm a newbie! Would you like to let me have your questions?

I'm from Zhuhai North Institute of Technology, a junior major, specializing in playing stand-alone, and you've found the right person for your question.

Here's the situation. Now I don't know the exact configuration of your host. The problem can only be solved according to conjecture.

1.If your motherboard is a low-to-mid-range motherboard that you bought earlier (2005-2006) and the graphics card slot is AGP, then Crysis 2 does not support graphics cards with AGP graphics card slots. "Crysis 2" is a masterpiece of 2011.

As early as the second half of 2007, the newer motherboards at that time already had PCI-Express graphics card slots, and the new stand-alone works from 2008 generally support PCI-Express graphics card slots and motherboards, so "Crysis 2" absolutely does not support graphics cards with AGP graphics card slots.

2.If your motherboard is still a motherboard from the Pentium 4 single-core CPU era, the memory module slot at that time is still DDR1, and sorry, Crysis 2 does not support this type of memory.

If there is any inaccuracy in the past, please continue to ask questions and reply after receiving it. I may not be at the same level as your actual situation, please understand.

Missing game add-ons You're looking at what the machine isn't loaded.

The system has not modified the workaround. We all know that most of the services in the system are interdependent, so in fact, we only need to start these two services to solve the above problems

1. Start the DCOM service and change it from manual to automatic;

2. Start the Remote Procedure Call (RPC) service, change manual to automatic;

After starting the above two services, it is found that the installer service will no longer be automatically closed, and the installer will not be automatically stopped.

Step 1: In the command window, enter Enter Service and check whether the Windows Installer service has been started.

The Windows Installer service is the way to add, modify, and remove Windows Installer (*msi), if this service is disabled, any service that relies solely on it will not be started.

Step 2: Check the DCOM Server Process Launcher service, set the startup type to Automatic, and start it.

Step 3: Check the Remote Procedure Call (RPC) service, set the startup type to Automatic, and start.

Restore the system or reinstall the system