My XPSP2 one click recovery How to use it

Enter ghost from dos state, enter If the system is unstable or the system file is wrong, please press the F8 key when booting up, select "Return to the operating system selection menu" ->ms-dos" after the menu appears, enter the command: *:ghost g "Enter" (that is, the Enter key on the keyboard), and then the system will automatically run the system recovery program, during this time, please do not do anything, wait for the program to run 100%, and after the automatic restart, the system recovery is complete!!

2) If the system can't boot (the computer prompts: disk i o error replace the disk, and then press any key or: disk boot failure, insert system disk and press enter

Find a CD or floppy disk with boot, put it in the CD-ROM or floppy drive, press the del key to enter the CMOS settings when booting (move the cursor to the Advanced CMOS setup, 1stboot device or the first boot device under the Advanced CMOS fearures) and change the system boot sequence to "CD-ROM or floppy" to boot. Then boot it up with a floppy disk or disc and enter the command:

ghost g "enter" (that is, the enter key on the keyboard), then the system will automatically run the system recovery program, during this time, please do not do anything, wait for the program to run 100%, automatically restart, the system recovery is complete!

Before restoring the system, please remember to copy the important files you need under the system C: disk to another disk, otherwise after the system is restored, all the files under the C: disk will be restored to the files when the computer was first purchased!!

The number is the disk where your ghost file is located, such as C drive, etc.

1. Open the one-click ghost program in the computer, you will see the system file information that has been backed up before, the default option is (one-click restore system) item, click (restore).

2. After clicking (Restore), a dialog box will pop up, prompting that the recovery system must restart the computer, click (OK), and the computer will automatically restart.

3. The computer will automatically choose to enter the one-key ghost program during the restart, and the program will automatically restore the system Yunyan Song, and the whole recovery process does not require any operation, and the recovery process takes about 3 minutes.

4. Finally, it will prompt that the one-click system recovery is successful! The computer will automatically reboot into the system that was previously backed up.

5. Before restoring the system, you should transfer the useful files of the C drive and desktop to other partition disks, so as not to cause the loss of personal useful files.

If you want to restore with one click, you must first have a backup. There are a lot of one-click ghost tools on the Internet.,You installed it in the case of an intact early attack search in the system.,Lu Li is backed up.,The next time the system collapses.,You can restore it with one click.。

You can use the restore tool that comes with the system to restore with one click, and the steps are as follows:

1. Enable System Restore.

Right-click "My Computer" - "Properties" - "System Restore" on the desktop, remove the check box of "Turn off System Restore on all drives", and click "OK".

2. Create a system restore point.

2.Select "Create a restore point" and click "Next" to open the "Create a restore point" dialog box.

3.In the "Restore Description Point" text box, enter the name used to identify the restore point, for example, enter "Before installing the software", click the "Create" button, and the "Restore Point Created" dialog box appears.

4.Click the "Close" button, a restore point called "Before installing the software" is stored in the computer, when the system is restored, find it and follow the operation steps, and the system will be restored to the state you "before installing the software".

3. Use System Restore.

2.Select "Restore my computer to an earlier time" and click "Next" to open the "Select a restore point" dialog box;

3.Click a date that you think is working properly as the restore point, and click "Next" to open the "Confirm restore point" dialog box;

4.Once confirmed, click Next and the system will restore.

First of all, we need to install a one-click restore software when the system is stable and some of the software we commonly use is installed. If you don't have a computer that comes with one-click restore software, go to the official website of Qitu one-click restore.

Open the one-click ghost program in the computer, you will see the previously backed up system file information, the default option is (one-click restore system) item, click (restore);

A dialog box pops up, prompting that the recovery system must restart the computer, click (OK), and the computer will automatically restart;

During the computer reboot process, it will automatically choose to enter the one-click ghost program, the program will automatically restore the system, the whole recovery process does not require any operation, and the recovery process will take about 3 minutes;

Finally, it will prompt that the system is restored successfully with one click! The computer will automatically reboot into the system from the previous backup.

It is most convenient to use the system's built-in restore tool, which can restore all the partitions of the disk on your machine to the state of the restore point you set.

1. Enable Settings System Restore.

Right-click on "My Computer" - "Properties" - System Restore - Remove the check box in front of "Turn off System Restore on all drives" - OK.

2. Create a system restore point.

2. Select "Create a restore point" and click "Next" to open the "Create a restore point" dialog box.

3. In the "Restore Description Point" text box, enter the name used to identify the restore point, for example, enter "Before installing the software", click the "Create" button, and the "Restore Point Created" dialog box appears;

4. Click the "Close" button, a restore point called "Before installing the software" is stored in your computer, when the system is restored, find it and follow the operation steps to do it, and the system will be restored to the state you "before installing the software".

3. Use System Restore.

2. Select "Restore my computer to an earlier time" - next, open the "Select a restore point" dialog box;

3. Click a date that you think is running normally as the restore point--- next step to open the "Confirm Restore Point" dialog box;

4. After confirmation, click Next, and the system will restore;

Answer, support me.

That is, to reinstall the system, it is recommended to use a USB flash drive to complete the reinstallation system.

stop: 0x00000ed reason:

1. It is caused by an error in the disk, and sometimes it is also recommended to check whether the hard disk connection is not in good contact.

2. This error occurs frequently, which is likely to be a precursor to hard disk damage.

3. Sometimes there is a problem with the memory, and this blue screen code will be displayed.

Solution: 1. Sometimes, restarting will solve the problem.

2. Replug the power cable and data cable of the hard disk.

3. Turn on the computer, press the DEL key (F2 or other for notebooks) to enter CMOS (or BIOS), find the Boot tab, and set the HDD of the hard disk as the first boot item. Press the F10 key to save and press the Y key to exit the restart.

4. Unplug the memory module, clean the gold finger and memory slot of the memory module, and then install it.

5. Enter the DOS system and execute"chkdsk

r"command to check the repaired hard drive.

6. It is recommended to use the PE system to enter the Windows repair world leakage surface and repair the system.

7. Enter the PE system, use the hard disk detection tool DiskGen to detect the hard disk and rebuild the MBR. If the hard drive is damaged, replace it.