What is the installation method of a fast heating electric water heater?

Install a filter. Instantaneous water heaters must be fitted with a filter at the water inlet, as there is a small amount of debris in the tap water to avoid getting stuck in the floating field (dry boiling, not heating) or clogging the shower (the water outlet is getting smaller and smaller). If the filter is clogged, the flow rate will be reduced, the water outlet will be smaller, and the floating magnet will not work, and the water heater will not be able to heat.

After a period of use, remove the filter and clean it, and it is ready to use.

Check the "Floating" position. When installing the water heater, the staff must remember to check whether the "floating magnet" is at the lower end and make it in a state of free movement to ensure the normal use of the water heater. Because the floating magnet is the water and electricity linkage switch, open the water valve to automatically heat, turn off the water to stop heating, if there are debris stuck in the floating magnet, the water heater will appear dry heating or no heating, clear the debris on the floating magnet, in order to work normally.

Control the flow of water. When installing the water heater, it is necessary to use a special shower equipped with the manufacturer, and the water heater can adjust the water flow or increase the water temperature under normal working conditions. However, the general user does not have the habit of controlling the flow of the faucet, resulting in the water temperature not reaching the predetermined effect.

Steps for the installation of instantaneous electric water heaters;

1.Positioning drilling, the positioning cardboard is close to the wall at the installation position, and the hole is marked with a marker;

2.Install the baffle and fix the baffle board to the wall with screws;

3.Install the main unit and install the water heater on the hanging plate;

4.Link the water inlet pipe, install a filter screen on the water inlet pipe, link it with the temperature control safety valve, and then connect it to the water inlet of the water heater;

5.Install the shower, link the shower and the lifting frame according to the instructions distributed by the manufacturer, and then connect the water heater with the outlet pipe;

6.Install the leakage protector on the upper right side of the water heater, connect the water heater power cord to the electric protector, align the live wire and ground wire, install the switch, and cover the waterproof panel;

7.Power-on test, close the leakage protection air switching power supply, the display panel is lit, turn on the water first and then turn on the power of the water heater, the left is the set temperature, and the right is the displayed temperature.

Because it should be distinguished from the previous kind of storage type electric water heater, the previous kind of electricity is turned on after the water is turned on, and it takes some time to have hot water to use, and such a water heater has no hot water after being used for a long time, and it is necessary to stop using it for a period of time before the hot water comes out. It is precisely because of such a water storage type that it takes a certain amount of time to wait when the original hot water is used up, so now this kind of water heater with hot water in 3-5 seconds after the water is turned on is called "instantaneous" electric water heater!

Instantaneous electric water heater refers to the patented products developed by some manufacturers in recent years or some products with high technical content imported from abroad. It not only has many advantages such as being able to heat up immediately, saving time and electricity, saving energy and environmental protection, but also has more and more economic benefits than ordinary electric water heaters, which are more and more favored by the majority of home appliance manufacturers and dealers.

Installation and purchase suggestions;

1) Although the instantaneous electric water heater has the characteristics of small footprint, fast water output, environmental protection and energy saving, but the power is high, and it is difficult for the average family meter to bear. The power of the instantaneous electric water heater is more than 4 6kw, and the current is 18 27A, which exceeds the current of 15A that most houses in China currently receive. Therefore, when families choose this electric water heater, they should consider whether it meets the requirements.

2) If the water consumption of the office is large, it is advisable to choose a commercial electric water heater with a power greater than 15kw.

3) In order to avoid the impact of noise on the office space, it is advisable to choose silent running products.

4) The maximum working pressure of the commercial electric water heater is recommended.

5) The inner tank has a special coating (such as Jingui material) to ensure anti-corrosion and anti-scale performance.

6) The water heater is small in size and easy to install.

7) The water heater has dual protection devices for temperature and pressure safety to ensure safe operation.

8) The water heater is able to run automatically.

9) High thermal efficiency, greater than 95% (high-grade, mid-range products).

10) When selected abroad, the power supply should be customized according to the local power supply of the embassies and consulates abroad, for example: the power supply in the United States is 120V, 60Hz, etc. Please inform the manufacturer in advance before ordering.

We all know that there are many types of electric water heaters now, and the quick and simple hydrothermal water heater is the most common one, and this kind of water heater is particularly convenient to use in life. When buying such a water heater, everyone needs to know how its quality is, so do you know how to install a fast-heating thermoelectric water heater? Let's take a look at the sail with youFast-heating thermoelectric water heatersHow to install and fast heating electric water heater?

1. Install the first place of the fast heating electric water heater type, and mark the holes in the wall with a pen. Then use screws to fix the scraper of the fast electric water heater to the wall.

2. At this time, we can also install the host on the top of the scraper. After installation, check if it is securely installed. After installing the main unit, the inlet and outlet pipes should be installed.

Install the electric wall at the location of the outlet pipe, then install the filter at the location of the water inlet, and connect the flow control valve.

3. After installing the shower, the shower and the water outlet should be caught, and then the power can be turned on and tested. If there is hot water, the installation is complete.

How about a fast heating electric water heater?

1. Energy saving: Quickly heat the electric water heater because it does not need to be preheated in advance, there is no heat loss when preheating, it is open when it is used, it is not turned off when needed, how much water will be released, even if there is no water storage water heater consumes more energy, which is used to consume unused waste hot water, and at the same time realizes energy saving, water saving, and water saving. In general, a fast-heating electric water heater can save 30% to 50% of electricity compared to a traditional electric water heater.

2. No need for preheating: Electric water heaters that usually heat up quickly have a wide range of power. When the faucet is on for a few seconds, it heats up hot water for 3 seconds and can quickly and conveniently meet hot water at the right temperature**. The fast-paced life of modern people needs.

3. Due to the high power, a lot of electricity will be consumed during operation, although the internal components of the fast heating electric water heater can effectively save energy, but it wastes some electricity compared with ordinary electric water heaters.

4. Although there are many advantages of this kind of fast heating electric water heater, but because its power is relatively large, it is necessary to reserve 4 square meters of copper core wire to install the water heater, if it is a southern city, the use of square meters of wires will be installed.

5. Quickly heat the water heater, no matter how many people use the bathtub, as long as the water temperature is adjusted before use, it can keep the water temperature constant after the water is discharged, so we don't have to worry about the water temperature during the bathing process. After a while, it had been very hot for a while.

6. Safety and environmental protection: For electric water heater products, everyone is most worried about safety. In order to fully protect the user, the fast heating electric water heater is also designed in this regard, such as non-metallic heating elements, leaky cover installation, grounding shielding and other methods.

Water heaters are inseparable from every family, and everyone needs to know how to choose when choosing, and of course it is important to learn to install them. The above is how to install the fast-heating thermoelectric water heater and how to install the fast-heating electric water heater introduced to you today, and this is the end of it.

With the improvement of living standards, more and more electrical appliances are used in every household, among which water heaters are deeply loved by consumers. It not only provides people with daily hot water, but also allows people to feel the comfort of bathing. So what is the installation method of an electric water heater?

What is the installation method of the electric water heater

First, install the water heater in a predetermined position with expansion screws; Then connect the hot and cold pipes of the water heater, pay attention to keep a certain distance between the pipes to avoid interference; Then connect the water heater circuit correctly and fix the socket; Finally, turn on the power of the water heater for testing, check whether there is water leakage, etc., if there is no problem, it can be used normally.

How to choose a water heater:

1. Capacity. First of all, when buying a water heater, pay attention to the capacity of the water heater, which can be determined according to the bathing time and the number of people, such as a bath for 20 minutes, you may need to consume 30 liters of hot water, if more than two people take a continuous bath, you may need 60 liters of hot water.

2. Power. Secondly, when purchasing a water heater, we should pay attention to its power, large power, fast heating speed, on the contrary, small power, natural heating speed and hunger will be slow. Some people mistakenly think that a water heater with low power is more energy-efficient, but in fact, regardless of the power, the electricity consumption is the same.

It is recommended to choose a water heater with high power, which is more convenient to use.

3. Function. Finally, when shopping for a water heater, look at its safety features. Too many other functions will seem frivolous, such as the remote control function, the distance remote control is not effective, and the distance is close and the remote control is not used.

Half-gall heating, heating with half the power, it is better to heat quickly, anyway, the power consumption is the same. As for the automatic switching of peak and valley electricity, there is no peak and valley electricity bill at home.

Summary: The above is the installation method of the electric water heater introduced to you and how to buy the relevant content of the water heater, I hope to bring help to friends in need, if you need to know more about the relevant knowledge in the later stage, welcome to pay attention to Qeeka Home information.