The computer is reinstalled, and the DEF disk data is gone, so I want to recover

Loss of the original partition caused by a mistake. If your partition structure is special, simply using partition recovery software, to a large extent, may not be able to find the correct partition data, wrong reconstruction, will destroy the original partition information, causing recovery difficulties. If it's a notebook partition, it's often special.

If you are familiar with data recovery, this situation can be easily recovered, now the computer can start the Internet normally, and the original data can be directly restored from the original disk through remote assistance. With the right operation, the system does not need to be reinstalled. Do not write a large amount of data to your current hard drive.

So as not to corrupt the data that may be recovered.

Be sure not to repartition, format, or anything like that. In that case, the recovered data is incomplete. Maintain the status quo.

To a large extent, the original data can be completely restored with proper analysis and processing. Without the need for data recovery software to scan the recovery. If you simply use data recovery software to scan and recover, it will take time and the effect is difficult to say.

If you want to try the recovery yourself, refer to scanning the recovery with data recovery software, and remember not to write the found files to the hard drive where the problem occurred. Instead, you should restore the found data to a different hard drive first. Make sure that the partition is correct before processing the problematic partition.

If there is nothing particularly important in the hard drive, then use the software to try to reply yourself, if so, it is recommended to go to a professional data recovery center to recover.

I replied to the software and suggested to take it"diskgenius"This software does a good job of recovery, and of course you can decide what software to use according to your preferences.

But the first and most important premise of using software to restore is that you can't write new data into the hard disk you want to recover, which will overwrite the original data and destroy the original data, so you can't recover.

Hello, the general computer partition is 2-4 areas, generally c, d, scramble e, f, to be used as a drive letter.

If you judge that your old computer can be used normally, but there is no D, E, and F drives, then it may be that your computer has no partition when installing the operating system, and the entire hard disk is a C drive.

Although it has little impact on the use of the computer, it is inconvenient for users to store files.

You can check the partition situation in the desktop icon "Collapse this computer", right-click, and "Manage" (as shown below).

If it is not poisoned, it is recommended that you change the system and repartition it.

Right-click on my computer first, then select the management option, and then select disk management and click to enter, then you can see d, e, f and other disks, but these disks have no name, no allocated disks, and then you can solve it yourself, as shown in the figure below.

By changing the drive letter and path on the specified disk partition via Disk Management, the hidden D and F drives can be easily retrieved.

Reinstall the system and then repartition it and you're good to go! However, there seem to be related tools to partition without reinstalling the system, but it is recommended to reinstall the system and partition it during the caution period!

You can divide the area in Disk Management and you don't need to reinstall it.

You can enter the system after partitioning.

The ghsot partition is missing and only the C drive is left, and it is estimated that you have made an error in the manual ghost step, resulting in the partition loss and only the C drive remains.

Manual ghost installation system correct steps: local—patrition—from image, if we choose this when restoring the system: local—disk—from we think that what we are going to do now is to back up the image file (*.) of the previous hard disk

gho) to the entire hard drive, and the result of this choice is simply to restore the backup image file of a partition that was originally backed up to the entire hard drive. As a result, the previous partition is lost and only a C drive is left, and it is best not to write data indiscriminately if you need to recover data.

To prevent the wrong operation from destroying the data again, it is more difficult to recover the data. It is recommended to refer to my space's "Ghost Partition Lost Only C Drive Left" to understand the situation clearly, and then decide how to operate. If you still need help, please contact me with information or continue to ask.

Can be restored. 1. If the previous file is installed on the C drive, the file or document cannot be recovered, because the files deleted during the installation of the system have been overwritten by the new system.

2. If the ** and the documents are in the partition outside the C drive, these ** documents will be intact and can be opened directly.

3. If other partitions are lost after formatting, there is no rewrite process. It can be used with EasyRecovery which can get back deleted files and even formatted hard drive files.

Typical ghost mistake,Caused by a big C disk occupies the entire space,If you don't understand this,It's really not in operation,Protecting the scene is the most important thing,Hi me,I'm doing data recovery,Data can be recovered。

Sweat. If you have a problem with your ghost system disk, it's best to find a professional data recovery company, if you do it yourself, remove the hard drive and install it on another computer, and then go to the data recovery software to try to see if you can get the relevant data back.

I used to be like you because of my own negligence.

Ways to save money: Don't move, put the hard drive on another computer and try recovery software.

If you have money: find a professional data recovery company, and the time is 3-4 hours. **In Guangzhou. Between 100-200.

Find an installation disk and use PE to go in and see, if not, you have to reinstall it.

There are generally two ways to reinstall a computer system: a new installation and an upgrade installation.

When you upgrade and install, the new operating system installer will upgrade the original system: you will pack the original files into a folder and install the new system on the original disk. Upgrading and installation generally does not cause the loss of the original partition and files.

There are generally two scenarios for a clean installation:

1.Format the C drive (system disk), not other hard disk partitions such as D and E. In this case, the files on drives D and E will not be lost.

2.Because the hard disk generates bad sectors or reinstalls the system after being poisoned, it is necessary to repartition and format the entire hard disk. All the data on the hard drive will be lost.

The problem must be that the maintenance engineer repartitioned the computer hard drive into C drive, D drive, and formatted it. Therefore, the computer only has C and D disks, and E disks disappear; The contents of the D drive have also changed.

It is recommended that in the future, try not to store personal files on the C disk, and at the same time, before reinstalling the system or sending it for repair, you must copy the full personal data and properly dispose of it to prevent privacy leakage or loss.

The computer city partitioned your hard disk, he formatted all your disks, because after poisoning, it is best to format the whole disk, so, divide the disk, and then format, so things have changed, there are no important files, it doesn't matter, I generally install the system myself, just format the C drive, the computer city is just for high efficiency, for the people.

Right-click"My computer"Click"Management"

Select"Storage"down"Disk management"

See if there is a disk partition on the right, if there is, see if the disk partition status is good, if not, your data is finished, just right-click at that point, select Format, and click Next until it is completed. And thy ristems will come out.

If it's good, see if there's a drive letter, and if not, assign one (right-click on the disk partition and select"Change the drive name and path", point"Add", and then OK), your data is intact.

The system installation only needs to format the system installation partition, which is generally a C disk; Others can be left untouched;

Formatting under PE,And then restore,But now ghost restore,It's equivalent to all emptying,Then write two steps to do one step,Fully automatic;

This is a one-click restore image to the C drive.

Did you use Windows 2000 or XP in the past, but now you use 98 system? If yes, then it's a matter of the file system format of the hard drive. Now commonly used is FAT32 and NTFS file system, if the D, E, F disk is NTFS, then the 98 system is not recognized, only reinstall back 2000 or XP, or use the 2000, XP installation disk, the D, E, F disk are formatted as FAT.