How to adjust the tightness of the drawer slide? How drawers are removed from the slide

1. First of all, take out the slide rail of the drawer that needs to be installed and place it as shown in the figure below.

2. Then check whether the movable track of the slide rail is sensitive.

3. Find the position of the fixed rail below, which needs to be installed on the cabinet.

4. Pull out the inner rail of the slide rail and install the fixed rail in the cabinet.

5. Then install the inner rail on the drawer, and adjust the tightness through the adjustment of the hole position.

6. After installation, directly put the drawer into the installed fixed rail for adjustment.

1. If it is a steel ball drawer, the middle rail and the outer rail are not kept horizontal, at this time there will be a situation that the shell cannot be pushed in, at this time either check the situation of the outer rail, tighten the fixing screws of the outer rail, and repair the deformed places.

2. If it is a wooden drawer, after the wooden drawer is wet, it will expand and get stuck on the guide rail, you can use sandpaper to polish the guide rail, and then smear some soap on the guide rail to lubricate.

Tools: screwdrivers, slide rails.

1. Pull the drawer out as far as possible, and a long black tapered buckle appears.

2. Use your hand to put the black protruding strip buckle and press it down (in most cases, it is downward, not excluding lifting it up), and the strip buckle will be lengthened, and then I feel that the slide rail is loose.

3. Press the long buckle on both sides at the same time, and pull out on both sides while pressing the long buckle with both hands, and the drawer will come out.

4. After pulling out the drawer, use a screwdriver to adjust the tightness of the screws to a suitable state.

There is a groove above and below the drawer slide, which is convenient for the slide ball to roll, and if you want to adjust the tightness, you only need to reduce or enlarge the range of motion up and down the slide.

Drawer: refers to the box used to put things in furniture such as tables and cabinets, which has a bottom and no cover, and can be pulled out and pushed in.

Drawer slide: Whether the drawer can be pushed and pulled freely and smoothly, and how the load bearing, depends on the support of the slide rail. From the current technology, the bottom slide rail is better than the side slide rail, and the overall connection with the drawer is better than the three-point connection.

The material, principle, structure, and process of the drawer slide are very different, and the high-quality slide rail has low resistance and long life.

1. First of all, take out the slide rail of the drawer that needs to be installed and place it as shown in the figure below.

2. Then check whether the movable track of the slide rail is sensitive.

3. Find the position of the fixed rail below, which needs to be installed on the cabinet.

4. Pull out the inner rail of the slide rail, and install the fixed ridge and fixed rail in the cabinet.

5. Then install the inner rail on the drawer, and adjust the tightness through the adjustment of the hole position.

6. After installation, directly put the drawer into the installed fixed rail for adjustment.

Here's how:The first step is to first pull out the drawer with both hands and pull the drawer to the end, as shown in the figure below

Step 2: Then lift your hands in front of the drawer and gently lift them up in the direction indicated by the arrow, as shown in the figure below

The third step is to lift the drawer and pull it out, as shown in the figure below

Fourth, the drawer will be successfully disassembled, as shown in the following figure:

Summary. First of all, take out the drawer slide first, and then check whether the movable rail of the slide can be pushed normally. Find the location of the lower rail, then install it on the cabinet, pull out the inner rail of the slide rail, and install the rails into the cabinet.

Install the inner rail on the drawer and adjust the tightness by adjusting the position of the hole.

First of all, take out the drawer slide rail, and then check and stare to check whether the movable track of the slide rail can be pushed normally. Find the position of the lower fixed rail, then install it on the cabinet, pull out the inner rail of the slide rail, and install the fixed rail into the cabinet. Install the inner rail on the drawer and adjust the tightness by adjusting the position of the hole.

What to pay attention to when buying a slippery Qing family rail1, load-bearing: The quality of the slide rail is directly related to the load-bearing capacity of the drawer. The load capacity of the drawer can be checked directly in the following ways.

Pull out the drawer completely, press the front and outside front front edge of the drawer with your hand, and observe the front inclination of the drawer from the side, the smaller the forward inclination, the stronger the carrying capacity of the drawer.

2. Internal structure: There is a bearing structure inside the slide rail, which is directly related to the bearing capacity. At present, there are both steel ball slides and silicone resin roller slides in the market.

The steel ball slide automatically removes the dust and dirt from the slide rail through the rolling of the steel ball to ensure that the cleanliness of the slide rail leaks quickly, and the sliding function is not affected by the dust entering the interior. At the same time, the steel ball spreads force around it, which ensures the horizontal and vertical stability of the drawer. Laughing.

I hope mine can help you and have a great day!

There are two main ways to adjust. The first is to adjust the slide parallel to the low point on the inside. The second is because the slide rail is unevenly installed, and the correct installation method is to be slightly lower on the inside than on the outside, because the drawer sinks when it is loaded with things, and it is balanced under the pressure of the center of gravity, and it does not slide outward.

1. The drawer screws are too tight to open: take a screwdriver to adjust the slide rail, if the screws in the drawer are too tight, it will be difficult to pull out the drawer, we can use a screwdriver to loosen the screws properly, it will be easier to get up, but not too loose, otherwise the drawer will fall down.

2. The drawer is stuck by a foreign object and cannot be opened: If the drawer at home is only bought, the reason why it cannot be opened is that it is stuck. At this time, don't pull hard, it will only cause the drawer to get stuck, find a ruler and put it into the gap above, move the drawer back and forth, pay attention to moving left and right, the amplitude should not be too large, be patient in the process, and you can take off the foreign object after a while.

1. First of all, it is necessary to figure out the structure of the steel ball pulley slide, which is divided into three parts: movable guide rail, intermediate guide rail and fixed guide rail. Among them, the movable cabinet is the inner rail; The fixed guide rail is the outer guide rail.

2. Before installing the track, we also need to remove the guide rails in the slide on the movable cabinet, and then install them on both sides of the drawer. Everyone should pay attention not to damage the slide when disassembling, although the disassembly method is simple, but you must pay attention.

3. Install the outer cabinet and the middle rail in the split slides on both sides of the drawer box, and install the inner rail on the drawer side panel at the same time. There will be reserved screw holes in the drawer, just find the corresponding upper screw.

4. After all the screws are fixed, you can push the drawer into the box. When installing, you should pay attention to the circlip of the inner rail, and then slowly push the drawer parallel to the bottom of the box to keep the balance on both sides. If you pull out the drawer and the drawer slides straight out, the circlip part is not stuck.

<>Here are the steps to remove the slide drawer:

Open the drawer and check how it is secured between the drawer and the slide. In general, drawers and slides are held together by fixing clips or screws on the slide rails.

Locate the fixing buckle or screw and have the spine remove it with a screwdriver or wrench.

Gently pull the drawer out towards you, taking care not to use too much force to avoid damaging the drawer or slide.

After disassembling the drawer, the slides can be removed from the furniture, cleaned or replaced.

To reinstall, you need to insert the slide rail into the fixing hole in the furniture, then place the drawer on the slide rail, and re-fix the fixing buckle or screw.

It should be noted that when removing and installing the slide leather drawer, it is necessary to be careful to close the seepage carefully to avoid damage caused by excessive force or improper operation. If you're not sure how to remove or install a drawer, seek help from a furniture professional.

1. Pull the drawer out as far as possible, and a long black tapered buckle will appear.

2. Press the black buckle, use your hand to put the black protruding long buckle, press down, most of the time it is down, do not rule it out, the long buckle will be elongated, and you will feel that the slide rail is loose.

3. Press the bayonet on both sides at the same time, press down and press the long buckle with both hands, and pull both sides outward at the same time.

4. Put the hand in, the black buckle is separated, if you just take things and don't need to pull out all the drawers, you can go in and get it.

5. To return the drawer, you only need to push the drawer back along the track, and the black buckle will automatically dock with the original card slot, push it back to the end, and then pull it back, and move freely once or twice back and forth.