How to connect the network cable to 100, how to connect the network cable

Is it two points with a route?

568b standard: orange-white-1, orange-2, green-white-3, blue-4, blue-white-5, green-6, brown-white-7, brown-8

100 Gigabit network cable: guarantee 1, 2, 3, 6 passes, can be used.

In addition, the same equipment uses a cross line, and different equipment uses a direct line;

Cross line: A+B, Straight line: A+A or B+B

In this era when everyone has to use the Internet everywhere, many low-headed people and mobile phone controllers are "living on the Internet". What if one day your internet cable is permanently broken? For many people, this is a crazy thing, you might as well solve it yourself, what if you can't pick it up?

Let's take a look at it nowHow to connect the network cablebar.

The network cable is 8 cores, there are 8 wires in it, in order to make the signal attenuation slower and the transmission distance farther, every 2 are twisted together to form 4 pairs, so it is called twisted pair.

How to connect the network cable

1. We use the peeling function of the network cable pliers to peel off the outer skin of the network cable, and we will see eight metal wires intertwined with color and white. Orange, green, blue, brown four colors, and they are intertwined with white orange, white green, white blue, white brown, some slightly orange, some just white, if it is a solid color, you must be careful, do not confuse the four white.

2. We remove their entanglements respectively, and pay attention to the order of placement: orange, green, blue, brown, white in front, and blue-green interchange. That is, the end result is: white orange, orange, white-green, blue, white-blue, green, white-brown, brown.

3. Divide the wire, use the wire cutter to press into the metal card slot of the network cable socket one by one. After each separation, do not crimp the line first, wait for all the lines to be placed, and use the same wire cutter to tie the wire one by one.

4. After cutting off the redundant lines, install the information module of the laid lines on the panel of the 86 boxes. There is also a line guard card behind a good network cable socket, which can protect the slight drag net infiltration plexus from falling off. Be careful not to pull the cable when placing the network cable socket inside the wall and on the socket panel.

5. Be sure to take a good look at the original old crystal head in what way to make it, we do it in accordance with its order, Cong Na because we are just making a crystal head, so we must "follow the local customs", otherwise, we must open the knife at both ends, and make it again in accordance with the standard.

We should pay attention to the length of the network cable when connecting the network cable, it is recommended that it is best not to be 100 meters long, because the longer the network cable, the worse the signal of the network will seem. The above is the relevant introduction to how to connect the network cable.

Tools needed: Mesh cable, scissors, hammer, stainless steel ruler.

1. Cut off the outer wrapping skin at one end of the network, revealing the copper wire inside, with a total of 8 pieces and 8 colors.

2. Arrange them in order, they are: orange-white, orange, green-white, blue, blue-white, green, brown-white, brown-white, brown-white, this is the industry standard order, and it can't be messed up.

3. Use scissors to cut the thread heads, and then insert them into the crystal heads, remember to push them to the end, so that the later production can be successful.

4. Press the metal head, use a ruler to snap into the crystal head buckle, and then put it flat on the ground.

5. Use a screwdriver and hammer to press each metal groove of the crystal head (use the hammer to gently tap the screwdriver).

If the screwdriver is too long and difficult to operate, you can use a shorter metal rod instead.

6. To make it simpler, you can also directly use a hammer to directly smash the crystal head, but be careful not to smash the crystal head.

7. Finally, it's done, plug it in the computer and try to connect to the Internet normally, and you're done.