What should I do if the ballpoint pen has ink but can t write

There are four reasons why a ballpoint pen can't write:

1.The pen accidentally fell to the ground, the ball was lost, and the nib was broken, resulting in the inability to use the oil normally.

2.If it is not used by mistake for a long time, it is difficult to get oiled.

3.Inferior ink can not be used in the ambient temperature range required by the national standard of 0-40, the ink will flow when the weather is hot, and it cannot be written when the weather is cold.

4.Improper use, wrong posture and angle of holding the pen for writing, resulting in the inability to write normally.

Solution:1The solution for the pen after falling to the ground.

Check whether there are balls at the nib, if not, take out the pen that has run out of oil before, take it out with tweezers and other tools, and attach it to this nib; The same treatment is given to the broken nib, and only the used good nib needs to be replaced.

2.The solution for not oiling after a long period of storage.

Put the pen barrel in hot water and heat it for 3 5 minutes, then take it out and shake the tip of the pen downwards vigorously; Or heating the nib with a lighter is also fine; or replace it with a good used nib; Blow air from the back of the barrel or let the ink into the air.

3.Inferior ink solution.

Keep it within a feasible temperature range and don't buy this brand again next time.

4.The solution to the problem of no oil due to improper use.

The standard writing angle national standard requires 47 degrees, and inferior nibs or inferior ink can only be written when vertical, and it is difficult to write or unable to write if you hold the pen barrel a little obliquely; Proper use of gel pens is also one of the ways to extend the life of gel pens, reducing wear and tear in use.

5.The ultimate solution.

The gel pen does not get oiled, it is nothing more than a problem with the nib or the pen and ink itself, the ball and the nib can be replaced, the pen and ink can be heated, and it is really not possible to change the refill. Look for high-quality brands, pay attention to how to use them, don't fall on the ground, and don't put them in a low temperature place.

You can take out the refill and shake it a few times.

There are also several ways to deal with it:

1. The method is very simple, and 100% easy to use, after taking out the refill, use the game lighter to bake the metal nib for two seconds, and then grab the tail of the ballpoint refill, and throw it two or three times in the direction of the nib.

2. Soak the tip of the pen in hot water for about 10 minutes, preferably two-thirds of the refill in the hot water, and then repeatedly circle a piece of paper until you can write it.

3. See if the beads are broken, if so, the pen can be scrapped.

Ink characteristics. Ballpoint pen ink is usually a paste containing about 25 to 40 dyes. The dye is suspended in a mixture of solvents and fatty acids.

The most common solvents are benzyl alcohol or phenoxyethanol, which mix with dyes and oils to form a smooth paste that dries quickly.

When writing, fatty acids help lubricate the nib. Hybrid ink also contains added lubricant in the ink to provide a smoother writing experience. The drying time of the ink depends on the viscosity of the ink and the diameter of the ball.

In general, the higher the viscosity of the ink, the faster it dries, but dispensing the ink requires the application of more writing pressure. However, despite their less viscous, hybrid inks have a faster drying time compared to regular ballpoint pen inks. Similarly, larger balls will distribute more ink and therefore increase the drying time.

The dyes used in the blue and black ballpoint pens are basal dyes based on triarylmethane and diazo compounds or phthalocyanine-derived acid sockish dyes. Common dyes in blue (and black) inks are Prussian blue, Victorian blue, methyl violet, crystal violet, and phthalocyanine blue. The dye eosin is commonly used in red inks.

Inks are water-repellent after drying, but can be smeared with certain solvents, including acetone and various alcohols.

The above content reference: Encyclopedia - ballpoint pen.

Hello, I've verified: soak a ballpoint pen or water-based pen in warm water, and you can write normally after taking it out! If you were me, I would have to thank you.

Shake: Hold the tail of the refill, shake it a few times with a little force downward, as long as the tip is not damaged, you can continue to use it.

Pick: The most reliable way to repair is "no repair". Learn to pick a good pen to reduce the chance of breaking ink. After all, if you break the ink during the exam and don't have a spare pen, it's a very troublesome thing.

There are also three methods: 1. You can use a needle to pierce two small holes at the top of the refill. 2. Soak the tip of the refill in hot water. 3. Use a rubber band to put it on the refill, turn the refill to make the band full of strength, and then release the refill to make it automatically reverse. You can try them one by one.

The solution to the fact that the ballpoint pen can't write the leakage can be adopted:

1. Method 1: Find a small stick that is thinner than the refill, wrap it in cotton, and insert it into the back end of the refill to form a piston. Push the piston lever and increase the air pressure in the refill until you can write smoothly.

2. Method 2: Rub the head of the refill on the sponge filter of the used cigarette. Fold the tissue in half and draw a ballpoint pen on the tissue for 10 seconds, or more.

Because the surface of the paper towel is rough, and the tip of the ballpoint pen is drawn on it, the ball can be rolled to remove the residue. At the upper end of the pen core, a small hole is pierced a little higher than the oil level, so that the air can easily enter, which can prevent the back end of the pen from being blocked to death, and the air pressure in the pen core is reduced after the oil level drops without oil. You can also try soaking the pen in hot water.

Second, the reason why the ballpoint pen does not produce water is:

This is mainly due to the fact that the dry ink oil adheres around the steel balls and obstructs the flow of ink. Ink is a viscous oil, which is made of flaxseed oil, synthetic pine nut oil (mainly containing terpene alcohols), mineral oil (oil obtained by fractionating petroleum and other minerals), hard glue and oil smoke.