In the bottom right corner of the screen, there is always a message that the file or directory is co

Start - Enter cmd enter.

Enter chkdsk f enter.

Enter y Enter next reboot to check for fixes (do not skip).

It's hard disk that has bad sectors. Reinstall the system to see if it can be solved. If not, you need a low-level hard drive. A low-cell hard drive should work out. Hope that helps.

Listen to me, you are the power off when the hard disk reads and writes, the directory is lost, it's not a big deal, the content is still there, the icon can't be found, the software problem, the possibility of bad sectors on the hard disk is small.

It is best to reinstall the system before observing, it is possible that the system files are missing.

It's good to reinstall the system, and remember not to skip chkdsk casually in the future

Hard disks have bad sectors, which can be solved by low-level hard disks.

Open the folder.

The file directory is corrupted and unreadable, and the reason for this issue is that there is a system error on the computer's disk.

The solution and operation steps are as follows:

1. First of all, open the computer desktop.

The "computer contains Liang guess", as shown in the figure below.

2. Secondly, after completing the above steps, right-click on any disk to open the "Slag Verticality" option as shown in the image below.

3. Then, after completing the above steps, click in the pop-up window to open the "Tools" tab, and then click the "Start Check" button as shown in the image below.

4. Finally, after completing the above steps, pop up the "Disk Check" window.

Options" and then click the Start button, and it will be executed automatically until it finishes, as shown in the following figure. After checking, the problem is solved.

When you open a folder, the file directory is corrupted and unreadable, and the reason for this problem is that there is a system error on your computer's disk.

The solution and operation steps are as follows:

1. First of all, open the "Computer" on the desktop of the computer, as shown in the figure below.

2. Secondly, after completing the above steps, right-click on any disk to open the Properties option as shown in the image below.

3. Then, after completing the above steps, click in the pop-up window to open the "Tools" tab, and then click the "Start Check" button as shown in the image below.

4. Finally, after completing the above steps, check the two options marked with red boxes under the "Disk Check Options" in the pop-up window, and then click the "Start" button, and then it will be automatically executed until it is finished, as shown in the following figure. After checking, the problem is solved.

You can try to right-click on the drive letter where your file is located (e.g. D drive) and select Properties, then select the tool options above, select "Start Check" in Error Troubleshooting, check "Automatically repair file system errors", and then click Start to take a look after the scan is over.

In this case, you can try to use AuroraDataRecovery software to recover file data by following the specific steps as follows

1. After opening the auroradatarecovery software, double-click the partition that needs to be recovered, then unzip it and right-click the software icon to select the software "Run as administrator" software (if it is an XP system, you can directly double-click to open the software).

2. After the program is opened, double-click the partition that needs to be recovered.

3. After the software scans the data, it will be placed in the same directory as the label of the leather beam coil to be recovered.

4. Tick the data to be recovered, right-click and select "Copy the checked file", and the program will copy the checked file.

5. The last step is to wait for the software to copy the data. If the problem persists, we recommend that you repeat the above steps and try again.

This prompt appears in the lower right corner of the taskbar (a file is corrupted, please run to use the chkdsk tool to repair), it is generally caused by too many junk files in the system, mainly junk files generated by the Internet, just clean it up.

Open a web page, click on the "Tools" menu on Internet Options under the "General" tab, click on "Delete cookies(i)", delete files pop-up, click on "OK" (including offline files), and restart the computer (no big problem, don't worry, no need to prompt the chkdsk tool).

2) The system comes with the disk repair method: (if the fault persists, repair the disk).

The specific steps are as follows (take Windows XP as an example), select the drive letter in My Computer, right-click, select "Tools Start Checking" in the pop-up drive properties window, select "Automatically Fix File System Errors" and "Scan and Recover Bad Sectors", and then click Start, the scanning time will vary depending on the disk capacity and scanning options.

3) If it still doesn't work, it may be that there is a problem with the hard disk, try to repair it with software. Bad sectors on the hard drive will lead to corruption or loss of computer system files, computer failure to boot or freeze. Hard disk bad sectors can be repaired using NDD Disk Utility or Scandisk.

4) If the fault persists, please restore the system or reinstall it (it is still not possible to format the hard disk and repartition and reinstall it, if it doesn't work, you will have to replace the hard disk, or overhaul it).

Just use 360 to choose the system to repair.

1. Open the software, click the hard disk you want to repair, right-click, and select Bad Sector Detection and Repair.

2. Click Try to repair, click OK and wait for the repair to complete.