PS2 model 30001 has some disks that read and some disks that don t read

Don't listen to people's nonsense, the bald head of PS2 is still quite leathery, and my 3W is still in service.

If you can't read it, it's because the bald head is aging, and it's OK to adjust it.

1. Open the bald head shell, wipe the bald lens with a cotton swab dipped in medical alcohol, wipe the upper and lower lenses, be careful when wiping the bottom, don't break the coil. Try it after wiping, and if it doesn't work, go to the next step.

2. The coin-sized white gear on the shelf of the dimmer head, which adjusts the height of the bald head. Adjust 1 or 2 teeth at a time, and in general, the ability to read the disc will be improved when the teeth are raised.

3. In the end, you can only adjust the power knob of the bald head, and the place of mediation is on the back of the bald head, there are two, one is ***, and the other is CD. Do not rotate at an angle greater than 5 degrees, and test after each adjustment. I also forgot the direction of rotation and which one is ***, so you'll know if you try it.

Finally, d9 and direct reading.

Generally, if the bald head is aging, you will not be able to read D9, the reason is that the reading time becomes longer, and the direct reading loses its effect after entering the 7-star picture, and the machine will have a red screen. That's the case with mine. Later, I switched to a direct reading and the problem was solved.

This direct reading can read out the pirated disc on the browsing screen and run it as if it were the original. This is also a feature that old-fashioned direct reading does not have. Therefore, it is recommended that you switch to a direct reading.

It's not a direct reading, it's your bald head that is aging, and of course some pirated disks are of poor quality. The bald head's ability to read disks decreases, and the quality of piracy is not good, so it is normal for many disks to be unreadable.

In your case, the only way to do this is to replace the bald head or adjust the laser emission power of the bald head, both of which are difficult for you to get yourself, so you should send them to the store to adjust them.

The best thing to do is to buy a hard drive and a network card, and play games directly with the hard drive, so that there will be no problems.

There are basically two reasons, but neither of them has anything to do with direct reading.

The machine has been out for a long time, and the aging of the bald head is inevitable.

2.The quality of today's pirated disks is really poor, and even if they can be read, the loss of the bald head is also very large.

Whether you can read D9 is related to the direct reading model, and has nothing to do with the host model.

It's best to read a good quality burning disc, I always use Verbati's plate to play games; Personally, I feel that since it is a thick machine, the entire network card and hard disk HDL are directly obtained, the speed is fast, and there is no need to consider the problem of the disk, and the game can be downloaded from the Internet**.

If the network speed is not good, it is a big deal to buy the image, and then take the image out, and then copy it to the hard disk.

Press and hold the reset button for 5 seconds to try, or reset twice in a row to try, if it doesn't work, then there is no rut! Direct reading is not supported or there is a problem with the motherboard

You can go to the game store and buy a boot disc.

You see, but the hatch cover is loose, and after I've been playing for more than a year, the lid is delivered, and the lid is pressed down when it starts.

Or the reason for the bald head.

If you are a second-hand PS2 bald head, there may be a problem with the new PS2, and it stands to reason that any dish can be read.

Or it's a matter of the disk.

You can rest for a few days to play, and if you can't read it, it's the reason for direct reading or baldness, and you must get js to change.

Now the quality of the D plate is too poor, take it to the game store to see if it's a bald problem, and now the PS2Z version of the disk is not expensive, pick a few classic and playable genuine versions to play, I wish you a good time!

If you buy a new machine, it's a matter of the plate.

Buy one again.

Find a boss to change the machine.

We have this 3 months warranty too.

The first possibility is that your disc is too bad, and the second possibility is that there is a problem with the bald head of your machine, and there are too many such problems with PS2.

It's a very old model, and there is only one reason, there is a problem with the bald head.

It is recommended that you take a clean soft cloth and gently wipe the bald mirror before reading, do not wipe with alcohol, save a little mineral water, a little less, blow dry and then read.

There are 2 reasons, the first is that there is a problem with the disc, and the second is that there is a problem with the bald head.

30000 is normal for poor disk reading ability, after all, it has been so long, and the bald head is almost the same, wash off the bald head, or buy a good FMCB card, so that the machine can play without disk.

30001 is a very old model, the aging of the bald head is inevitable, and the bald head is discontinued, and now it is impossible to buy a new one.

The best way is to change to a hard disk drive, but you can completely eliminate the bald head and discs. **Search --- PS2 hard drive.

Or. PS2 network card.

Or. PS2 to hard drive.

There are two ways to change the machine:

Hard disk + boot card + dedicated network card.

And. There are pros and cons to both ways of moving a hard drive + boot card (made by a memory card installer) ......

The bald head is aging, you use a soft cloth to wipe the upper and lower mirrors of the bald head, it is really not possible to replace the bald head, your thick machine 30001 bald head is basically gone, and there are also refurbished, and the price is also several hundred yuan. The moving laser rotation and twisting must be marked, and it can only be done little by little.

The bald head is aging.,But if you can still read the disk, hurry up and start the memory card.,After you do it, the bald head can be used without it.,Directly free game.。

The bald head is about 40 yuan, buy one online and take it to the store to repair.

The maintenance fee is only twenty or thirty yuan.

The 7W PS2 bald head is not expensive, and the bald head is new within a few tens of yuan.

It's normal that the disk can't be read, and many of the dozens of burning disks I bought can't be read after a few months, that is, they enter the seven-star screen (the picture where the seven light points are turning) or enter the memory card interface; Of course, sometimes it's a red screen.

You still have to try a few more to say, it's best to buy a few new pressure plates to try not to read the plate for a few reasons.

1. The problem of the disk itself (the disk will break itself after a long time, no matter how it is saved, it is useless; It is the most susceptible to breakage due to its engraved disc).

2. The bald head is aging and does not read the disk; What is the model of your own machine, search on the Internet, buy a bald head, and replace it with 3, direct reading problems; Often the red screen may be the direct reading is broken, and I will disassemble the machine to see the direct reading model and then buy one online and change it according to the welding diagram (this requires a certain amount of electronic knowledge and will use an electric soldering iron); I won't just go to js for a change.

I guess it's a problem with the disk.,After all, the life of pirated discs is relatively short.,You try to buy a new one to see if you can read it.,If you can, it's your disk problem.,Otherwise, it's your bald head that has a problem (it may also be that the direct reading chip is broken.,The probability is not large)