After the CD is put into the optical drive, all that comes out are some files, what should I do?

Install Storm Video, and then right-click on the G drive, and the pop-up option will be **cd or auto**, or in the "File" button of Storm Video, there will be the "**cd" option.

This phenomenon is generally caused by the following aspects:

1.The bald head accumulates dust, which makes the ability to read discs worse. If you can do the following, remove the optical drive, turn it on, and wipe the laser head a few times with a medicated cotton ball dipped in anhydrous alcohol or distilled water (wipe in parallel, do not wipe in circles.

Do not use detergent - it will form a film), dry for 20 minutes, and then repack. You can make the optical drive work for a while longer.

Ordinary users do not have the ability to do it, and it may be difficult to recover it when disassembled and cleaned, so it is recommended to buy a disc that cleans the bald head to use, and generally buys it where the disc is sold.

2.If it is not used for a long time, the transmission mechanism and moving components of the optical drive lack lubrication, so that the speed becomes low or cannot rotate at all. It could be that the laser mount slide shaft is out of oil or stuck. Clean the metal shaft and add some oil.

After putting the disc in, pay attention to whether there is a turning sound or other abnormal sounds, and you can judge it.

3.The laser head is aging. You can increase the output power of the laser head, there is an adjustment screw behind the laser head card holder, slowly rotate about 15 degrees, if not, turn 15 degrees, and try repeatedly until you can read the film.

4.Viruses do the trick. The optical drive was maliciously blocked in the registry.

See if the binary value of "Nodrivers" in "Hkey Current User Software Microsoft Windows Current Vrsion Polices Xplorer" is the value of the optical drive. Normally there is no such item, but you can also change the value of this item to "00 00 00 00" (01 00 00 00 is a, 04 00 00 00 is c, ff ff ff is hidden all drives).

Note: There are now viruses that specifically alter the registry so that the drive letter is lost. Some viruses will not cause the drive letter to be lost, but it will prohibit the optical drive from reading the disk, and it will not be able to read any disc, but it can be started with the disc.

5.Whether the driver of the optical drive is installed correctly. Or its driver is corrupted.

Usually Windows comes with a driver with an optical drive, and there is no need to add it separately. If the driver of the optical drive is not installed with its own driver, the optical drive will also be lost. This usually happens when so-called "optimizations", "accelerators" or other programs are added.

At this time, you can enter safe mode, delete the "cdrom" option in "Device Manager", and then restart the computer, let the system find the new hardware and reinstall the driver of the optical drive.

6.A lot of pirated *** discs, with the computer's *** optical drive can not be read, the quality of the disc is too poor.

7.The poor performance of the optical drive is generally found on the newly purchased assembled computer or the newly purchased optical drive, and there is a huge "humming" sound when reading the disk, and after eliminating the fault of the optical drive, it is likely that there is a problem with the power supply. It is necessary to take it apart and check it.

Prompt "Please insert the disk into drive X" or "Please insert an available disc": This is a disc that the recorder does not recognize. There are many reasons for this.

1.Check to see if you have selected the wrong optical drive (recorder). If you have two optical drives (recorders) on your computer, this prompt will appear if you select the wrong one.

2.If the chosen recorder is correct, check whether there is a problem with the disc, first, whether the disc is the corresponding category of the recorder, such as the CD recorder is put into the *** disc; Burn *** is not good if you put a CD disk, and the second is that if the disc is not wrong, you must consider that the quality of the disc is not good. You can change a few more plates, or try a different brand.

3.The disc has been burned, and there is data on it, or a waste disc that failed to be burned, etc. This prompt appears when the burner can't detect the disc or the detected disc doesn't meet the burning requirements.

4.If your recorder does not support burning the +R disk, this prompt will also appear when you put the +R disk. In short, it will only prompt if the recorder does not detect a suitable available disc.

5.If the performance of the recorder (optical drive) is degraded, and the disc cannot be found, it will also be prompted like this.

Hello! We're glad to answer your questions! Please read the following tips to eliminate your worries. Thank you!

1. Open a position to check whether the CD-R has been burned into the CD song, because the song in the CD is in the form of an audio track, and you can't see the file misjudgment.

2. The computer city purchased the CD cleaning kit, squeezed the detergent on the soft cloth brush, lightly brushed the blank CD-R burning disc, and burned the laser head stain of the optical drive.

4. Then find the instructions to flash the optical drive firmware correctly to improve the symptoms of picky discs. The problem still exists after refreshing, please call Pioneer customer service for feedback.

5. Communicate with the technical engineer and ask for help, be sure to reflect to him in detail and truthfully, the brand, model, speed and capacity of the burning disc you use.

6. As well as your computer's hardware configuration, system version, software installation and usage, burning software name and version, parameter settings, etc.

7, ** is not specific, you can ask the engineer for an e-mail, send him your details by e-mail, to help him analyze the reason.

8. Then write the corrected parameters into the new improved firmware and provide it for you to use next time you flash the optical drive. If there is no way to bypass it for the time being.

9. Consider buying a batch of blank CD-R discs of other brands to replace them. If it is still the same, it means that there is a problem with the optical drive laser head and needs to be repaired.

10. You can also try a different burning software before repairing, such as Nero Burning ROM, you can find the CD-R and burn it, it's good.

1. Open "My Computer" or "Computer" on the desktop, enter "Control Panel" in the address, and click Enter.

2. After entering the "Control Panel", click "Hardware and Sound".

If it doesn't respond and I can't see the drive letter after double-clicking on my computer, or if the drive letter is empty after opening, I will take the drive out first. Then right-click on my computer, select Properties--- Hardware--- Device Manager Find the item of the optical drive, right-click to uninstall the optical drive, and then restart it.

Go to someone else's computer to see if they can read it, and if you confirm that your CD is fine, it means that there is a problem with your optical drive.

Try a different disc, if you can read it, it means that you have a problem with the optical drive.

1. Open "My Computer" or "Empty Computer" on the desktop, enter "Control Panel" in the address, and click Enter.

2. After entering the "Control Panel", click "Hard Beam and Sound".

The most likely discs to be read are:

1. The disc is damaged. It's normal for the disc to be broken and not read. Try a different plate.

2. It is more common for the disk to be broken, the computer is broken, and it cannot be read. Replacement or repair.

In addition, CD-ROM (Compact Disc Read-Only Memory) is a type of optical disc that is used on a computer. This type of disc can only write data once, and the information is permanently stored on the disc and read out through the disc drive when used.

Open a folder, set the hidden files in the menu - Tools - Folder Options - View folder drive, and then open it again to see if there are files in the disc.