-
Anonymous users2024-02-07Measurement method of motor quality:1. Check whether the insulation resistance of the motor coil is greater than the megaohm, if it is greater than the megaohm, it means that the insulation performance of the motor is good;
2. Use the multimeter resistance file to test whether the DC resistance of the 3 windings of the motor is the same, if it is the same or the size deviation of the DC resistance of the 3 windings is very small, it means that there is no inter-turn short circuit between the coils of the 3 windings;
3. Manually rotate the shaft of the motor, and check whether there is any disc immobility, abnormal noise, etc.
4. Check the quality of the motor, check whether the insulation resistance of the motor coil is greater than the megaohm with the insulation resistance shake table, if it is greater than the megaohm, it means that the insulation performance of the motor is good.
-
Anonymous users2024-02-061. How to test the quality of AC three-phase motor?
1. Shake the meter, 500V can shake the meter, and shake the insulation resistance of the wire on the three binding posts to the motor shell, which should be above Europe, indicating that there is no short circuit to the ground.
2. Multimeter measurement: measure the resistance between the three phases of ab c, whether it is equal, it should be about the same, and the difference is too much, but it will not take long, remember that the larger the motor, the smaller the resistance! But you can't all three phases be 0 ohms, unless you are particularly large, such as a motor above 50kw!
Remember, if it is a speed regulating motor, the resistance value of the 6 terminals is not the same!
3. Check the bearings and fans, and generally wrap the motor to let them all be replaced! Because sometimes the bearing will burn the motor!
4. The no-load current of the motor is generally 10% to 50% of the rated current, and sometimes the idling current of the motor is still zero!
5. When the rated current of the motor is running, it is running at full load, and the output power is basically 100%. The running current is small, which means that the output power of the motor becomes smaller, and it is a light load operation.
2. How to detect the quality of AC single-phase motor?
Use a 500V megohmmeter to measure the insulation resistance of the motor winding and the shell, which should not be less than the megohm; Use a multimeter to measure each lead wire of the winding, and there is no broken wire; All of the above meet the requirements, and the motor is good.
It is more convenient to use a pointer multimeter to detect the quality of the capacitor (there is also a digital meter with a capacitance file, which can be measured directly).
It is good to dial the multimeter to the 1k or 10k resistance level, measure the 2 leads of the capacitor, and slowly return to the left capacitor after the meter needle is quickly deflected to the right; Always biased to the right indicates that the capacitor is broken; If the pointer does not move, the capacitor will be disconnected or the capacitance will be gone. In this way, only the quality of the capacitor can be judged.
Three. Is a DC motor good or bad?
First see if there is a broken wire and measure whether the resistance is normal.
If it is a brushed DC motor, the rotor can be rotated and the output DC can be measured with a multimeter to see if the output DC is normal.
If it is a brushless DC motor and the three-phase is drawn, the rotor can be rotated, and the multimeter is used to measure whether the output alternating voltage is normal.
The output voltage is proportional to the rotational speed.
You're definitely talking about AC motors, because DC motors are two wires. Solution: (Remember that I have been doing electrical maintenance in the factory for 20 years, and this is how I taught my disciples!) ） >>>More
First of all, you have to have enough equipment, according to the situation of the landlord is to listen to it with a stereo, to use a good stereo (the loudspeaker on the road is useless to play a good song) Secondly, the sensitivity of human ears to sound quality is different, so some people can not hear the very subtle differences in sound quality, we call him fungus. I think the landlord can turn on the louder sound to listen to it, and the difference is still obvious when using the stereo.
For one-way thyristors, use the R 1 gear of the pointer meter to find out the two feet that are not passable, and the remaining leg must be the control pole. The red pen and the black pen of the pointer universal table, connect the two levels that do not pass, and the short circuit of the control pole and the foot of the black pen will rotate the indicator at a certain angle. Detach the control pole from the black pen, and if you keep the pointer moving, the black pen will be connected to the anode, and the red pen will be connected to the cathode. >>>More
Specific gravity test method:
There is a specific gravity solution on the market that measures the specific gravity of gemstones; We can use specific gravity to test real and fake diamonds. The specific gravity of natural diamonds is that all natural diamonds sink when placed in specific gravity water, so any gemstone that floats on specific gravity water can be sure that it is not a diamond. >>>More
Hello, I am also in adolescence now, but I don't have early love, I find that the phenomenon of early love is very common around me, I go to school in the countryside, and there are more early loves. There may be more open cities. In fact, puppy love is not a dirty problem, maybe adults complicate it, I look at the classmates around me, the good of puppy love is: >>>More