-
Anonymous users2024-02-07If you're approaching the warranty period, it's better to change the micro-motion yourself.
Because: First: the mailing warranty has to wait for about half a month, which is a waste of time and costs postage.
Second: changing the micro movement is also changing the same micro movement, and it will still change to double click after another year.
Third, even if it's not mailed, it's troublesome to go out.
So, buy it online for more than a dozen good micro-motions to solve this small problem and save time and convenience!
Therefore, the real connoisseur will not worry about the problem of micro-motion at all, the connoisseur will change it by himself, and if there is a problem, he can replace it on the spot, just a matter of ten minutes.
Buy it a dozen micro-movements at a time, enough to use the mouse is eliminated.
Some references for players who buy for themselves:
The order in which the fretting motion is good or bad.
Omron White Point D2FC-F-7N < Omron White Point D2FC-F-7N (10M) "Omron White Point D2FC-F-7N (20M)" "Nissan White Point D2F-01F-T
The last of them costs at least 7 yuan, but the reputation of the feel is better than the others.
In addition, it is recommended to buy a micro motion at the same time, you can refer to the mouse foot sticker that buys Teflon, because this is also a consumable part, you can buy it all at once, and you can use the mouse for so long when the shell is broken.
-
Anonymous users2024-02-06When the mouse clicks, there is a power connection, my original dell has been used for four years, and this year there is also this problem. It is uncomfortable to use evil, and it has been replaced.
-
Anonymous users2024-02-05Hello, if you decisively find after-sales service in the warranty, change the micro motion yourself, ** micro motion is not expensive, but you need electric welding, generally there is no equipment.
-
Anonymous users2024-02-04Generally speaking, the occurrence of a mouse click becoming a double click is mostly caused by a mouse failure, but it may also be due to a mouse click becoming a double click due to an incorrect setting operation.
The first thing to do is to rule out setup issues.
1.Open Mouse Properties in the Control Panel.
2.Select the Mouse Keys tab and try unchecking the "Enable Click Lock" check in the "Click Lock" bar at the bottom.
In addition, try to connect the mouse to other computers, if the problem still exists, then it is basically certain that the mouse is faulty, this type of fault is basically a small fault, and it is relatively simple to repair.
Maintenance tools: a Phillips screwdriver, a piece of cardboard, a pin.
1.First, pry open the foot stickers and remove the screws.
2.Disassemble the mouse shell and find the micro switch corresponding to the left mouse button.
3.Use a pin to pry the snap of the micro switch.
Note: 1) Since the buckle is a plastic product and is very thin, it will be broken and damaged if you are not careful, resulting in the mouse basically not being used in the future.
2) There is a metal spring in the micro switch, and the spring will pop out while priing open the buckle, and the spring will not be found if you don't pay attention to the clever dismantling, so it is best to have some things around to block the spring sheet, and to observe carefully and operate gently.
4.When we click the mouse, the contact on the spring will be in contact with the metal copper contact below, and the computer will make corresponding contact, that is, click and double-click, which is quite wide in the principle of the switch.
5.The reason why the mouse clicks and double-clicks are mostly caused by the poor contact of the shrapnel inside the mouse. We can use a piece of cardboard to polish the copper shrapnel to solve the poor contact caused by burrs, rust and other conditions in the contacts.
After that, we can install the removed mouse parts.
It's that kind of situation that can't be opened.
After double-clicking the mouse, there is a slight funnel chart, and then it is gone, and there is no response; >>>More
If you do not add a right-click shortcut key to Notepad during system installation, you can add it as follows: >>>More
In this case, there should be a problem with the micro switch of the mouse, which is a typical mouse failure, click does not respond, click becomes double click, can not drag the file, can not select text or file, can not take a screenshot, etc. are all micro motion problems, the main reason is that the contact of the micro switch under the button is oxidized, so that the contact is not in good contact. Share a method to detect the change of click to double-click: first open the computer's program - accessories - calculator, then enter 0+1= in the calculator, and then click the = sign, if the mouse is normal, the result should be every click on the = sign, and the displayed operation result will be added by 1; If the mouse has a click to double-click, the operation result will sometimes appear that the click will show the situation of adding 2, if there is a click but the display of adding 2, it means that your mouse has a click to double-click, and this situation will become more and more serious after a short time (this is because the micro switch has been oxidized very much). >>>More
Generally speaking, most people have double eyelid cutting is more obvious, because the double eyelid cutting is a more traditional surgical method, which is to form a double eyelid effect by using the fat in the eyelid, but there are also some people whose eyelid fat is too thick, and the postoperative effect may be slightly worse. But as long as you do enough aftercare, the effect is also obvious, many people think that it is easy to cut double eyelids after swollen eyes, let's find out. >>>More
Hello! I'm [Rong Zixuan], since the book you want has been sent If you are satisfied with the article I sent, then quickly adopt my answer. >>>More