What should I do if I want to change back to VISTA after installing XP ACER4920? The original shortc

The question is simple. Buying Vista's original installation CD from the market is all you need to go. Remember not how much of oneness is now.

It is the one that can choose the version in the early installation. During the installation process, enter the serial number that your Acer computer affixes to the machine. It can be activated normally.

Because the manufacturer is only the serial number purchased from Microsoft, there is no difference as to what media is used to install the system. The system installed using this method is the one that needs to install the driver itself and does not have the software that is installed randomly at the factory by the acer base. But the software isn't of much use.

Q: What should I do if I want to change back to Vista after installing XP on ACER4920?

A: Since you have a hidden partition, you can restore it directly with one click!

Q: The original shortcut key cannot be used to restore the original settings!

A: What are the original shortcut keys? Do you want to restore the shortcut of the original settings, or restore the shortcut settings to the original settings? Hey, your question is very technical.

Q: Question addendum: I don't want to go through the disc, the machine itself has a hidden restore partition, but it can't start up when it is in XP!

A: That's right, just resume sprinkling. If one-click restore is also what you call a shortcut that you can't use. Hey, you don't want to pass the CD!

Press F10 to try when you turn it on, my classmates can use it, if not, go to the after-sales center, free and safe.

Put the supplied Vista recovery disc into the CD-ROM drive, select the CD-ROM to boot, and restore it directly to the C drive, remember to back up the data of the C drive before.

It is recommended to format the XP after installing Vista, directly with the Vista with the machine can be installed, it is not recommended to use recovery, recovery will produce some garbage, personal feeling is still unstable.

For the 10g you can delete it and see if there are any changes.

This problem is not a problem with the system partition, the problem is related to the system you installed in the XP.

Just change the XP system, mine is also acer, I also formatted the previous 10G partition, no problem.

I suggest you call Toshiba**80082020482 you can consult.

If the hidden partition of your hard drive is not corrupted, you can directly restore the hard drive to the pre-installed Vista system.

The specific operation method is: press and hold the 0 button at the same time to turn on the computer, and then operate according to the prompts.

Factory reset must ensure that the partition state of the C: disk is exactly the same as the factory state, if you have changed the size of the C: factory state, it cannot be restored.

2 illiterate upstairs.

If the two systems are interchanged, then all the data on the previous system will be erased, so the one-click restore of the original factory is gone.

So you don't want to restore it with one click.

And Vista is an excessive system is rubbish.,Even win7 is not as good as you still use xp win7 has a lot of games,The software is not compatible with how to install Vista refer to xp installation。

There is also the PE system on the first floor, you have to copy it to a USB flash drive before you can install it, or a CD, and there are very few Vista mirror fool systems on the market.

You just use XP.

To add, if you go to a specialty store and buy it, they should be free for life, and if you sell it in a hypermarket, they don't care.

After you turn off the computer, press and hold the 0 key on the number 0, p, more than three seconds, and then don't let go of the 0, and press the power button at the same time, until you turn on the computer and then let go, give it a try,,, pay attention to the installation when choosing not to change the hard disk partition...

Normal, this kind of problem will generally occur when the system is changed.

Three pieces of software are required. Install the Toshiba Universal module first, then install the Toshiba Power Saver program, and then install the Toshiba hotkey program.

Toshiba Universal Module.

Power management program.

Keyboard hotkey program.

Go to the official ** to find the driver, if you don't have it, you will be troubled.