Citizen quartz watches are not gone, how much does it cost to repair the watch

Generally**about 100 yuan.

Citizen Eco-Drive Watch Repair, Warranty**.

When the Eco-Drive radio-controlled watch fails, please contact the after-sales service department of Citizen in time. The inspection and maintenance of radio-controlled watches is a very specialized technology, which requires a series of special testing equipment and instruments, which are not available in general repair shops. Faulty Eco-Drive meters must be sent to Citizen for inspection and repair.

1.The watch suddenly stops moving, or the second hand does not move for more than 15 minutes while receiving the signal. It may be affected by external impacts, static electricity, magnetic fields, etc. It can also be caused by a number of reasons, such as insufficient charging, mechanical transmission, or faulty integrated circuits.

2.After being overcharged, the watch stops after a few days of operation, which may be due to the mechanical part, the rechargeable battery not being charged, the conversion energy of the solar cell is reduced, etc.

3.The watch can receive a signal, but the time is inaccurate, and it still does not run accurately after clearing the process.

Citizen Beijing Maintenance Service Center.

6. Closed on Sundays.

Hello, it should be the battery is dead, mine is like this, I don't know if yours is not, I was repaired last time in Jingshi Hengda maintenance center, through the online appointment, and enjoy a 9% discount, about 100, and the master also helped me to test for free, to see if there are other problems, really good. Hope it helps.

Hello, the quartz watch appears to stop, generally due to the battery is not charged, the standard maintenance of the ordinary quartz watch to replace the battery ** is 100 yuan, if the movement needs to be repaired, the maintenance ** needs to be based on the model of the watch and the maintenance content. If you have any questions, you can call customer service **400-650-1958 for consultation.

Cheap, even cheaper if you change the battery, 180 yuan.

Quartz watchThe maintenance method is as follows

1. The quartz watch battery has no power or insufficient capacity, and needs to be replaced with a new battery. Generally, the conventional battery can be used for 2-3 years of analog quartz watches, if the battery is found to be powerless in a short period of time after replacing the battery, this situation is generally due to the large power consumption of the watch's functions, such as the analog quartz watch and the LCD function model.

Another is caused by the low quality of the battery itself. Check whether the battery is charged during the inspection, and replace the battery with a new one if there is no power. If the battery is detected, it may be something else.

2. Quartz watches stop and go or directly "strike not go", we judge that there should be dirt on the positive and negative contact reeds of the watch contact battery or the battery is not installed in place, and the contact between the signal output point on the circuit board and the lead point of the coil wire will also cause poor contact. These will cause the circuit to not turn on, so that the quartz electronic watch does not go or does not go well.

If the circuit is not connected due to poor contact, the contact reed and the poles of the battery need to be fully cleaned, and then reinstalled.

3. The old quartz watch may be due to a broken coil. Because quartz watches generally have a lifespan of about 10 years, over time due to oxidation of the coil of the quartz watch, or man-made reasons that damage the coil, can pass through the multimeter.

Test and check, and generally need to replace the coil.

4. There is no output signal on the circuit board of the quartz meter tested with a multimeter, and all other aspects of the inspection are normal, most of the reasons are caused by the damage of the quartz oscillator or the failure of the integrated circuit. It is recommended to replace the quartz oscillator first, and if that still does not work, the entire circuit board needs to be replaced.

5. Check the core stepping motor.

It cannot be rotated, and the rotor of the magnetic stepper motor can not be rotated if it is stuck, causing the quartz watch pointer to stop or stop from time to time.

6. If the mechanical gear train of the quartz machine core is faulty, check whether there is any debris and dust between the gear teeth, which will affect the normal operation of the gear train. There is also an excess of core oil, which makes the wheels sticky to the splint. The solution was to wash the mechanical components of the quartz watch.

Summary. The maintenance of mechanical watches** mainly depends on the maintenance and replacement parts of the watch** and the maintenance labor charge**. The more expensive the watch, the more expensive the replacement will be.

Generally, the maintenance of mechanical watches ranges from hundreds to thousands, and if it is an expensive watch, the repair cost of tens of thousands of dollars also exists. The maintenance of mechanical watches** mainly depends on the maintenance and replacement parts of the watch** and the maintenance labor charge**. The more expensive the watch, the more expensive the replacement will be.

Generally, the maintenance of mechanical watches ranges from hundreds to thousands, and if it is an expensive watch, the repair cost of tens of thousands of dollars also exists.

How much does it cost to repair a mechanical watch.

The maintenance of mechanical watches** mainly depends on the maintenance and replacement parts of the watch** and the maintenance labor charge**. The more expensive the watch, the more expensive the replacement will be. Generally, the maintenance of mechanical watches ranges from hundreds to thousands, and if it is an expensive watch, the repair cost of tens of thousands of dollars also exists.

The maintenance of mechanical watches** mainly depends on the maintenance and replacement parts of the watch** and the maintenance labor charge**. The more expensive the watch, the more expensive the replacement will be. Generally, the maintenance of mechanical watches ranges from hundreds to thousands, and if it is an expensive watch, the repair cost of tens of thousands of dollars also exists.

The maintenance of mechanical watches** mainly depends on the maintenance and replacement parts of the watch** and the maintenance labor charge**. The more expensive the watch, the more expensive the replacement will be. Generally, the maintenance of mechanical watches ranges from hundreds to thousands, and if it is an expensive watch, the repair cost of tens of thousands of dollars also exists.

Quartz watches do not go away The repair method is as follows:

1. Find the reason from the energy **. If the quartz watch is gone, it may be that the quartz watch battery is dead or the capacity is insufficient, and then we need to replace the battery of the watch. When we check the watch battery, we should also observe whether the battery is in poor contact, whether there is dirt in the positive and negative reeds, etc., if so, remove these dirt first and then look at the replacement battery.

2. Gear train failure. Open the back case of the quartz watch to see if there is no dust or foreign matter between the lower wheel teeth, and whether there is any jam between the wheel trains. Whether there is too much or too little oil between the teeth, if there is more oil, it must be cleaned, and then an appropriate amount of oil is added; If there is less oil, add an appropriate amount of oil.

3. The coil is broken. Quartz watches have been used for a long time, and the internal coils may be oxidized or artificially damaged, this can be tested with a multimeter, and if it is broken, it needs to be replaced.

4. The quartz oscillator is damaged. The above mentioned quartz meter is not the reason for the analysis is not, then it should be the quartz oscillator damage or integration envy let the circuit fail, the use of the universal meter can detect the circuit, then the quartz oscillator or circuit failure, the entire circuit board should be replaced.

Quartz watch daily maintenance method

1. High temperature and waterproof. It is best not to expose quartz watches to the sun, and you should also pay attention to waterproofing every day. The high temperature will accelerate the aging of its waterproof rubber ring, and it is easy to lose the waterproof function.

2. Shockproof. Vigorous** can easily have an impact on quartz watches, and if you wear them for sports, frequent and strong waves of your hands can easily cause damage to your quartz watches.

3. Anti-magnetic. If the quartz watch is magnetized, it will also be affected to a certain extent, such as a large error when walking, of course, it is easy to solve the problem, just go to a professional watch store for demagnetization.

4. Dustproof. If a quartz watch is exposed to dust for a long time, fine dust will enter the case, which will accelerate the drying of the engine oil and affect the aesthetics, so it is also important to clean the watch regularly.

Hello, I am happy to serve you and give you the following answer: Citizen mechanical watch is not gone, it may be due to the failure or damage of the precision parts of the mechanical watch, resulting in the mechanical watch can not operate normally. First of all, the battery of the mechanical watch should be checked to see if it is depleted, and if it is depleted, it can be replaced with a new one so that the mechanical watch can function properly.

Secondly, the mechanical parts of the mechanical watch should be checked for damage, and if there are damaged parts, they should be replaced with new parts in time

Summary. Dear, let me answer: it should be a lack of kinetic energy, which may be caused by your usual lack of exercise, or that you don't take the watch for a long time.

You can shake the watch to make it move and see if it can walk. If not, it is recommended that you go to a professional watch repair center for testing, so that you can accurately know where the specific problem is, so as to solve the problem of the watch.

What's going on with the Citizen mechanical watch not gone.

The Citizen watch strap I just bought suddenly stopped leaving.

Dear, let me answer: it should be a lack of kinetic energy, which may be caused by your usual lack of exercise, or that you don't take the watch for a long time. You can shake the watch to make it move and see if it can walk.

If not, it is recommended that you go to a professional watch repair center for testing, so that you can accurately know where the specific problem is, so as to solve the problem of the watch.

Extended information: First, you first wind it manually to see if it will go; or will go, indicating that the watch is good and there is no problem; If you are a fully automatic mechanical watch, you should wear it for 8 hours a day. If it's light, you need to get it out to the sun! Second, if you wind it manually and the watch still won't go, it means that there is something wrong with the watch, and you need to take it to the store for a physical examination to know the exact problem.

The quartz watch battery has no power or insufficient capacity, just replace it with a new battery. When the quartz watch suddenly doesn't go, that's the first thing we have to think about. 2.

The contact is not good, most of them are dirt on the positive and negative electrode contact reeds, and the contact with the battery is poor. The contact surfaces are cleaned thoroughly before being reassembled. 3.

When a quartz watch comes into contact with a magnetic field, it stops moving due to the magnetic field. But rest assured, a quartz watch is not the same as a mechanical watch, it will not be magnetized. As long as it is out of the magnetic field range, it will be fine.

4.Coil breaking, due to oxidation or man-made reasons, so that the coil is damaged, can be checked by multimeter testing, and generally needs to be replaced. 5.

Gear train failure, which occurs because there is dust or foreign matter between the gear teeth, which causes the gear train teeth to jam each other. Cleaning should be carried out to remove foreign bodies. 6.

The quartz meter has no output signal, and other aspects have been checked, which is generally caused by the failure of the integrated circuit board, in which case it is necessary to replace the entire integrated circuit board, which is a more serious problem.

The law was also turned by hand, but it still did not go.

If you really can't do it, you can only go to your local watch repair place and let the professional watch repairers take a look, or you can only find a merchant<>

<>Oh, that's going to be taken back to Japan to be repaired, and it's been less than two months since I bought it."

Yes, you can contact the merchant and mail it over to see what the merchant has to say, <>