What is the fault of the Little Swan Water Cube washing machine when the water enters the water for

1) The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged, it will not move.

2) The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3) The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic washing machine are completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally.

4) Poor motor performance and capacitance problems, resulting in insufficient output power, can be solved by replacing the capacitor.

The fully automatic washing machine stopped washing in a few minutes.

5) The fastening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged. If this is the case, in most cases, an empty washing machine can be dehydrated.

6) The washing and dewatering of the fully automatic automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally.

The Little Swan washing machine may be cut off after two minutes of water entering the washing machine, probably because the water level you set is relatively low, so try to adjust the water level setting. Generally speaking, this is the only reason, otherwise it is broken.

The water cube washing machine you are talking about is a fully automatic washing machine, and it stops water after two minutes of water intake, indicating that there is a problem with his computer control program. You can go to the after-sales service to repair it.

The reason why the Little Swan Water Cube washing machine stops water after two minutes of water intake is because there is something wrong with its water inlet system, and you have to find a professional after-sales department. Repair.

It may be some of your water washing machine, the system turns to water to tell that there may be some failures, you can ask a professional master to check it for you, so that you can solve this kind of fault problem.

Little Swan's Rubik's Cube washing machine was cut off after two minutes of water ingress, so check whether there is a problem with the line.

You give a ** to the after-sales maintenance, and let them come home to repair it for you.

Generally, this kind of washing machine should be able to be broken for two minutes.

You're saying here that it's hard to judge without seeing. You should ask a professional to come up to your house and have a look.

When one of his clothes was already dry, he stopped.

The washing machine cannot be dehydrated, mostly because of the safety switch in the cover.

It can be overhauled as follows:

1. First check the safety switch in the cover, which is mostly caused by poor contact or wear and displacement caused by ablation of the switch contact. Turn on the power program of the washing machine to the dehydration state, if you press the brake arm of the safety switch by hand or tool to close the upper and lower contacts to dehydrate normally, it means that the contacts are ablated and cause poor contact, you can use sandpaper to polish the upper and lower contacts brightly, or replace the new switch. In addition, it is important to check whether the switch lever is worn and displaced, resulting in the switch lever unable to close the contacts after the cover is closed, and a new safety switch of the same specification should be replaced at this time.

If the washing machine alarms and the digital tube shows "E1" after the switch contact is closed normally, the computer board should be overhauled or replaced.

2. If in the dehydration state, only the wave wheel rotates and the inner barrel does not rotate, at this time, you should check whether the traction has put the clutch pawls and ratchet.

If there is no possibility that the nut of the adjusting rod on the drain valve is loose and worn, resulting in insufficient opening distance, the distance of the adjusting rod should be readjusted so that it can separate the pawl and ratchet wheel of the clutch.

Turn on the power first, then press the wash button, the number in the middle is changing, let the number be zero, press the rinse button in the next step, the number in the middle is also 0, press the dehydration in the third step, let the number be 1, and then press the start button, you can dehydrate. I tried. Very easy to use.

The principle is to let washing and rinsing not work, only dehydration.

1. The inlet valve is faulty.

When the water inflow does not stop, first observe the water level in the barrel and the wave wheel. If the water is still entering the water when the preset water level is reached, but the wave wheel starts to run, it means that there is a problem with the water inlet valve. At this time, unplug the power supply line of the water inlet valve, if the water is still in, it means that the water inlet valve is broken, and it can be replaced.

If the water inlet stops after unplugging the power supply cable, it means that the program control board relay is sticking.

2. Problems with water level switches and impulse hoses.

Observe the water level in the bucket, if the water level exceeds the preset water level and the wave wheel does not rotate, it means that the water level switch or impulse hose is a problem. At this time, open the back panel of the machine, first observe whether there is water or leakage in the pressure hose (generally transparent), if the water leakage indicates that it is its problem, just seal and connect it from the new. If there is no water in the pipe, it is a water level switch problem, and an alternative method can be used.

Try it. 3. Program control board problem.

In the failure of non-stop water ingress, the probability of problems with the program control board is very small. There is a waterproof layer on the surface of the program control board of the washing machine, and the replacement of the whole board generally does not support maintenance, so it is recommended to contact professional maintenance personnel for maintenance.

1. The general situation is that the valve core of the inlet valve is stuck, and it cannot be reset after being opened after being energized, resulting in water inlet all the time, and the water inlet valve is replaced first. 2. If the fault is not solved, the problem lies in the water level switch, after a long period of use, the water level switch can stop the water ingress, causing the water inlet not to stop, at this time the water level switch should be replaced. 3. If the pressure pipe is worn and broken due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle or disconnected, causing air leakage, it can also lead to more than water ingress, because the computer board is not under pressure and the water level switch does not act and is misunderstood as the water level is not more than water ingress, at this time, the pressure pipe should be checked for wear and whether there is poor contact or disconnection between the two joints.

4. Due to the use of a long time, there is a foreign object blocking the air valve mouth, resulting in the pressure can not be transmitted to the pressure switch, at this time the big nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air valve. 5. If everything is invalid, you should try to replace the computer board, because all actions are controlled by the computer board.

Cygnet. Reasons why the automatic washing machine can't sink water and how to deal with it:

1. Check whether there are foreign objects (coins, brooches, buttons, etc.) stuck in the drain valve core, resulting in the drainage valve core cannot be returned to the position and cannot be closed to drain the water while entering the water, and the solution is to take out the foreign body.

2. Check that the drainage tractor (drainage motor) is faulty, and the drainage cable does not return, resulting in drainage while entering the water, and the solution is to replace the drainage tractor.

3. Check the failure of the water level switch or water level sensor, the water level pressure cannot be sensed, resulting in drainage while entering the water, and the solution is to replace the water level switch or water level sensor.

4. Check that the water pressure air guide pipe is broken or loose, and the pressure to water level switch or water level sensor cannot be provided, resulting in drainage while entering the water, and the solution is to adjust and replace the water pressure air guide pipe.

5. If it does not work, the central shaft may leak for a long time, burn out the motor, and replace the motor.

Take a closer look at the instruction manual of your washing machine, is it an upper drain or a lower drain? If the washing machine is drained, then it can be connected to the water pipe and placed directly in the drain. If the washing machine is drained, the water distribution pipe must be bent to a certain height and then come down to connect the drain.

In this case, the machine that goes to work is not bent to a certain height and is directly connected to the drain, so the water flows away.

Once the washing machine does not stop flooding, there are two reasons for its failure: 1. The water level switch itself is faulty, 2. The microcomputer controller of the washing machine is faulty.

There are two possible troubleshooting methods, the first is to replace the water level switch, and then to see if the fault situation is eliminated. If it cannot be eliminated, it is necessary to carefully check the computer control circuit, which is generally a microcomputer failure and needs to be replaced; Or find the damaged components on the computer board, replace them, and restore the water seal of the computer board.

Check it yourself if the pipe connected to the water level switch is broken, causing the measurement of the water level to be inaccurate. My family was like this once, just pick it up.

Can you listen to the pause? If it doesn't stop, the inlet valve is broken, and if it stops, it's the sensor or.

Problems with the motherboard.

It's the water level switch that is broken, just replace it.