The Little Swan washing machine hits the barrel switch, and the Little Swan washing machine spins dr

In case the unbalanced clothing causes the bucket to be broken, it is usually under the water inlet valve.

Super shock switch, there is something wrong with your equipment, it is not right to hit the barrel, hurry up and repair it.

1. If your washing machine is fully automatic with a wave wheel, the anti-collision barrel switch is generally in the left front corner (facing the washing machine), and you can touch it by reaching into it. Its function is to "prevent the washing machine from hitting the box due to the imbalance of the centrifuge barrel when it is spinning".

2. Under normal circumstances, it will not collide with the centrifuge barrel. In general, after a collision, the washing machine will stop and then rinse in water to automatically balance the clothes; However, if this question arises all the time, you should consider:

1) Whether the washing machine is leveled (that is, horizontal), under normal circumstances, the laundry bucket should be in the middle, if not, it can be leveled by the adjusting feet under the box (one or two front feet are adjustable).

2) Do not wash large and small clothes together, such as washing bed sheets, ** and ordinary clothes together. In this way, it is easy for the large clothes to wrap the small clothes, causing the center of gravity of the clothes to deviate to the side of the barrel and cause the barrel to collide, and it is difficult to correct it automatically, and it needs to be paused for manual leveling.

3) After going home and unpacking, be sure to remove the plastic or foam that fixes the laundry bucket at the bottom of the washing machine box, otherwise it may also affect the operation of the centrifugal barrel during use.

4) The centrifugal barrel is suspended by 4 booms and shock absorbing springs, if the boom and shock absorbing springs fail, it will also lead to hitting the barrel. Such as boom bending, spring misalignment, etc. This needs to be ruled out by the manufacturer's professional after-sales service.

Hope it helps!

However, it is still recommended that you hit the manufacturer's after-sales service** and let the professionals judge!

Reasons: 1. Improper use, the most common is that the dried clothes are not placed evenly, or too many clothes are put in. 2. The components that are obviously damaged and easy to cause cylinder collision are:

1) The sealed leather bowl is damaged. (2) If the motor or capacitor is tipped dry, the speed of the motor cannot reach the designed speed, and the phenomenon of spinning the dry barrel hitting the cylinder will also occur. (3) The connecting shaft sleeve between the spin bucket and the motor is damaged, especially the connecting hole at the end of the spin bucket of the aluminum shaft sleeve is grinded, resulting in the unstable spin bucket.

4) The spring bracket of the spin-off motor is obviously damaged. Maintenance method: 1. Turn off the water and power of the washing machine, turn the direction and prepare for disassembly.

Remove all the screws on the back cover with a screwdriver. Open the lid and lift and pull down the damper with your hand to find that it has lost its damping effect, so it is determined that the fault is on the four booms. 2. Remove the screws on both sides of the lid of the washing machine, and there is a screw on each side of the panel after the lid is opened, and cover it with a rubber cap.

Remove the two rubber caps with an awl to see the screws inside. After twisting the two screws with a screwdriver, open the upper lid and you can see a boom at each of the four corners. 3. Hold the iron rod of the boom and push it up to separate the iron rod from the fixed seat and the washing machine, and then use the other hand to rotate the direction of the plastic seat so that one of the positions with holes is aligned with the hook of the iron rod to facilitate its exit.

4. Tilt the washing machine forward and smoothly take out one of the four booms. 5. Pushing or pulling the damper by hand does not have any damping effect, indicating that it has been damaged. At this time, replace it with a new product.

6. Install the newly purchased set of four new damping booms as they are, and tighten all the fixing screws to restore the washing machine to its original position.

There are many reasons why the Little Swan washing machine won't rotate, such as not being connected to the power supply; The machine was not started properly; Other reasons cause the machine to fail to enter the mode of starting the motor; The control board, the motor itself, and related wiring or machinery are stuck, etc., which will cause the motor to not rotate. 1. Eliminate the problem of external power supply and wrong operation method, the washing machine motor does not rotate, the first situation is that the motor has a problem, such as a short circuit or burnout, and the motor coil has an inter-turn short circuit fault, which can only be replaced with new components. 2. When the motor does not rotate:

It is possible that the motor leads have no voltage, and the leads need to be overhauled; It may be that the electronic program controller has no output, and the electronic program controller needs to be overhauled or replaced; It is possible that the capacitor is damaged, in which case the capacitor needs to be replaced; It is possible that the motor is damaged, in which case the motor needs to be replaced. 3. Turn on the washing machine and fill it to the set water level: the wave wheel does not rotate in the forward and reverse directions.

In this case, the general motor rotation performance is as follows, the wave wheel is stuck, and the washing machine cannot hear the sound of rotation, which means that the wave wheel is stuck. Carefully remove foreign objects from the washing machine. Hope mine helps you, thanks!

Find who to repair and call for maintenance**400 998 7997 Someone will come to repair thank you, you're welcome, I wish you a happy life!

Hello dear, the reasons why the inner barrel of the Little Swan washing machine does not rotate may be as follows:1Motor Failure:

It may be that there is a problem with the motor or control circuit, which is causing the inner barrel to not function properly. 2.Belt slip or break:

If the belt inside the washing machine is slippery or broken, it will also cause the internal sales bucket to not rotate properly. 3.Inner barrel bearing failure:

A faulty inner barrel bearing may also cause the inner barrel to fail to rotate and the bearing condition needs to be checked for repair or replacement. 4.Wear and tear of transmission parts:

If the transmission parts inside the washing machine, such as sprockets and gears, are worn, the inner barrel will not rotate normally. It is recommended that when you check these issues, be sure to turn off the power and disconnect the power plug, and seek professional help.

Yes. The safety switch, as the name suggests, is of course a safety protection.

For example, the type hand is a safety switch used in washing machines

Almost all fully automatic washing machines will have a safe opening of the bus. When the washing machine is running at high speed, such as spinning, if the user opens the top cover of the washing machine (or opens the top cover to a certain height), the washing machine stops working, and a beep is emitted to raise the spine for a signal, and the display will display the corresponding error**.

How to replace the safety switch.

1. First, unscrew out the fixing screws of fixing the face frame and the water baffle plate according to the above steps;

2. Unscrew out the two screws that fix the safety switch, and pull out the two lead pins connecting the safety switch;

3. Replace the new safety switch and assemble it according to the original steps.

Yes. Little Swan Washing Key Dust Roller is a product developed and produced by Wuxi Little Swan Co., Ltd., which can be seen from the instructions for the use of the product: the bucket switch, safety door switch, and door cover switch of the washing machine are integrated, so the bucket switch is the safety door switch, and the manuscript is located in the left front corner of the washing machine, and it can be pressed gently.

Summary. Step 1: Unplug the washing machine.

Use a wooden nail pick or chopsticks to clean the opening and closing of the drum cover. Remove any detergent dirt that has accumulated around the drum cover. Sometimes the dirt of the detergent covering the metal parts is too thick for the drum lid to close tightly, causing the washing machine to not work.

Step 2: If the cleaning is ineffective, remove the top cover of the chassis and look at the switches. Once the switch is exposed, check if the screws are loose.

If the screws are loose, the switch will move when the drum cover closes or when the washing machine starts working. Check the terminal block of the switch to make sure the wiring is secure. After aligning the switch, tighten the mounting screws.

If it doesn't work, you can only go for repairs.

Can you add, I don't quite understand it.

Step 1: Unplug the washing machine. Use a wooden nail pick or chopsticks to clean the opening and closing of the drum cover.

Remove any detergent dirt that has accumulated around the drum cover. Sometimes the dirt of the detergent covering the metal parts is too thick for the drum lid to close tightly, causing the washing machine to not work. Calling the Acacia Step 2:

If cleaning doesn't work, remove the top cover of the chassis and check the switches. After the switch is exposed, check whether the screw is loose or not. If the screws are loose, the switch will move when the drum cover closes or when the washing machine starts working.

Check the terminal block of the switch to make sure the wiring is secure. After aligning the switch, tighten the mounting screws. If it doesn't work, you can only go for repairs.

Summary. Hello dear, Little Swan drum washing machine fault analysis and maintenance: this fault is mainly due to the poor performance of the water pressure switch, so that when the air pressure in the gas collection room has not reached the specified pressure, its contact will be converted from a disconnected state to a closed state in advance and stop water inlet, the specific reasons and treatment methods are.

1. The pre-compression amount of the water level control spring of the water pressure switch becomes smaller, as long as the adjusting screw is screwed in to increase the pre-compression of the water level control spring. If the water level control spring becomes less elastic or loses its elasticity, the water level control spring should be replaced. 2. The groove on the cam of the water pressure switch is worn or damaged, and the cam can generally be replaced to solve the problem.

Hello dear, Little Swan drum washing machine fault analysis and maintenance: this fault is mainly due to the poor performance of the water pressure switch, so that when the air pressure in the gas collection room has not reached the specified pressure, its contact will be converted from a disconnected state to a closed state in advance and stop water inlet, the specific reasons and treatment methods are. 1. The pre-compression amount of the water level control spring of the water pressure switch becomes smaller, as long as the adjusting screw is screwed in to increase the pre-compression of the water level control spring.

If the water level control spring becomes less elastic or loses its elasticity, the water level control spring should be replaced. 2. The groove on the cam of the water pressure switch is worn or damaged, and the cam can generally be replaced to solve the problem.

The press did not respond.

The washing machine shows h0 because the washing machine has malfunctioned, is not working, and cannot start. Or the internal temperature is too high and you need to wait for the temperature to drop down, you can wait for half an hour to solve the problem at the starting point: turn on the drainage pump, clean up the dirty things inside, check whether the drainage pump is loose, if you can't solve it manually, you can contact the after-sales personnel.