How to install a remote controlled quadcopter, model B500

Quadcopter is also known as quadcopter, quadcopter***, referred to as quadcopter, quadrotor. This quadrotor is a multi-rotor aircraft. The four propellers of the quadcopter are all simple mechanisms that are directly connected to the motors, and the cross-shaped layout allows the aircraft to adjust its attitude by changing the speed of the motors to obtain the force to rotate the fuselage.

The specific technical details are described in the "Basic Principles of Motion". [1] Because of its inherent complexity, there has never been a large commercial quadcopter in history. [1] In recent years, thanks to the development of MEMS technology, stable quadcopters have received extensive attention, and their application prospects are very impressive.

The more well-known quadcopter companies in the world include China's DJI, France's Parrot, Germany's ASCTEC and the United States' 3D Robotics.

Ask a professional to help you install it, or you see, there's an airplane in the sky.

Can there be anything difficult to do for Du Niang?

The function is to control the quadcopter.

How to use in detail**:

1. Turn the switch of the quadcopter to ON, and the switch of the remote control to ON.

2. Push and pull the joystick of the remote control, up and down, left and right, for pairing, if the remote control beeps, it will be regarded as successful pairing.

3. Push the joystick to control the quadcopter.

4. Pull the lever to push the exercise, push the left joystick up is to fly the plane upward, if the left joystick is pushed down, it is down, and the right joystick is to control the left and right forward direction.

5. Landing, slowly pull the joystick down, don't move the right joystick, and slowly pull down the left joystick until the landing is successful.

Copy function of quadcopter remote controller:

The small quadcopter can freely hover and move freely in space, with great flexibility. It has a simple structure and good mechanical stability, so it is low cost and cost-effective.

How to use the quadcopter remote control:

1. Turn on the power switch of the remote control, the indicator light of the remote control is flashing at this time, push the throttle to the maximum control stroke first, and then put it at the bottom, and the indicator light becomes solid.

2. Install the battery on the battery rack of the flying saucer and turn on the power supply on the flying saucer.

3. Place the flying saucer on the flat ground steadily, so that the red indicator light on the receiving board changes from a fast flashing state to a slow flashing state, and the flying saucer enters the remote control state.

Specifically, look at the inside: content.

It is on the instruction manual that comes with the aircraft.

The installation is not in the method, the key is in the later stage of the start-up to zero, or whether the actual operation angle meets the needs, the rest is none of your business.

Those who have played the flight controller still don't understand this, but there is also the fact that the detection axis of the flight control board should be in the same direction as the axis of the motion axis.

Give a good review oh dear.

Eliminate several problems: 1. The remote control is damaged, 2. The receiver is damaged, 3. The remote controller is out of power, 4. Whether the flight controller is unlocked, 5. Whether the flight controller is connected to the computer (some flight controllers will disconnect the remote control after connecting to the computer for IMU calibration, and the reading and writing chip must be unplugged and restarted).

If you don't have the above problems, see if it's caused by the following problems:

There is no code match between the receiver and the remote control, this is on the manual, and the code is successfully matched according to the operation.

If the operation of the code finds that the receiver light is not on, that is, the receiver is out of power, then check whether the signal line of the receiver is correctly connected to the flight controller, and the signal line has at least one set of +- plugs to connect the connection position of the flight controller receiver to supply power to the receiver.

If these are all right, you should check whether the flight controller has normal power supply, whether the flight controller is normal self-test, if not, the flight controller or power supply circuit may be damaged, or the wiring is incorrect.

If you are a toy, you can, put the two slurries and the motor flush forward or backward installation, note that you can only use the four-axis wiring, only the first two of the four-axis can be used. If you really model airplane, the remote controller and receiver are a system, the flight controller is a system, the four-axis power is a system, when used as a fighter jet, there are only two parts, the remote controller, receiver and power, and the fixed wing can fly normally without the flight controller.

As long as the flight controller is reset or removed, it can be installed on a fixed-wing aircraft and used.

When installing, pay attention to distinguish between positive and negative propellers, and also pay attention to the following: Some models, the fastening nuts of the propellers are also divided into positive and negative teeth.