Why can t the memory module be installed? How to secure the computer memory module? I can t put it o

I want to ask you, what is your memory sd ddr ddr2?

And what kind of memory your motherboard supports.

If the board supports your memory, you aim it at its slot, and there is a gap in the memory (DDR is two, SD is two), balance your hands and press the two buttons, and you just hold on.

It may be caused by the non-standard specifications of your memory module, or the specifications of your socket.

If the direction is right, the cards on both sides of the slot will be stuck in the memory, you can refer to other memory on the motherboard to see.

It means that you are SD plug DDR or DDR plug SD, the slot specifications are different, of course you can't plug in.

The three memory slots, SD, DDR, DDR2, and not all three memory slots are compatible with each other. In particular, DDR is the closest to DDR2 in appearance, but it is also not compatible.

Also, pay attention to the orientation of the memory module when inserted.

Just plug it in, and you're good to go, remember, turn it off and turn it off.

To standard, specifications of the memory module,

Are you using AMD CPUs? Currently, AMD's motherboards do not support DDR2 memory. So if you want to use DDR memory, I think you should find the reason in DDR and DDR2 memory.

Because I also had a situation like you yesterday, it's OK to change the DDR, or the card slot in the middle is a little worse

Some of the memory specifications are right! SD and DDR will definitely not be able to install it if they are mixed!

It can be gently smashed into it with a hammer.

Computer memory module installation process:

First, press the two buckles of the memory module to open them completely.

Second, at this time, you need to distinguish the direction of the memory module, and pay attention to a small gap on the memory module.

Third, there will also be a gap in the memory slot.

Fourth, the notch on the memory module and the notch on the socket need to be consistent.

5. After aligning the notch, insert the memory module into the slot, and press the spike with both fingers (the force needs to be even).

Sixth, the snap of the spike chain acupressure to both ends of the plug guess clan grandson groove automatically fastens the memory module, so that the memory module is installed.

1. The slots of the memory generally have a locking buckle. When inserting and unplugging memory modules, be sure to open the locking clasp before inserting or withdrawing them. (Dial the locking buckle outward to unlock) below**, the white switch circled by the red rectangle is the locking buckle.

2. Of course, if the memory module is plugged in backwards, it will not be plugged in. When inserting the memory, align the metal contacts of the memory with the slot (to ensure that the interface and slot can match), and then press down until you hear a "click". The memory latching clasp will lock automatically, and both sides must be locked to be fully plugged in.

The most likely reason is that it is plugged in backwards.

A memory module is a computer component that can be addressed by the CPU and can be read and written. Memory modules used to be an extension of the main memory in the history of personal computers. With the continuous update of computer software and hardware technology, memory modules have become the whole of read and write memory.

When we talk about the size of a computer's memory (RAM), we refer to the total capacity of the memory module.

Memory modules are an essential part of a computer, and the CPU can address the memory through the data master cable. Historically, computer motherboards had main memory, and memory modules were extensions of the main memory. In the future, there will be no main memory on the motherboard of the computer, and the CPU will rely on the memory module.

All content on external memory must pass through memory in order to function.

How to install the desktop memory module, you only need three points to press the memory module yourself.

The memory module is directional, I didn't see a gap in the middle of the memory module, aimed at the main card slot, and pressed it.

For desktops, pay attention to the fact that there is a concave on the gold finger of the memory module, which corresponds to the motherboard, and just insert it directly.

In the case of notebooks, pay attention to the small concave as well, but insert it diagonally about 45 degrees, obliquely refers to the insertion angle.

There is a clip on both sides of the card slot of the memory, after opening, the notch of the memory module is aligned with the protrusion of the motherboard, and you can press it a little harder.

For the opening, plug it in and press down, first press one end and then the other end. The card heads on both sides are stuck in and installed. Miscellaneous motherboard old machine, easy to contact, not good to try a few times, the new motherboard will be no problem. If it doesn't work, change the motherboard, there is a problem with the circuit or bridge.