May I ask if the computer is booted after the memory is detected and played, why do I need to press

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select the "Advanced BIOS Features" setting item and press the Enter key to enter;

Set "Boot Up Floppy Seek" to "disabled" to turn off boot software detection.

To add to them, in addition to the situation they said, some machines only need to enter the BIOS, and then press F10 to solve this problem in determining the exit, some machines need to go in and block the floppy drive to solve it, generally with the former situation I said, you can get it This is the manufacturer's problem when making, if your machine is an old machine, there was no problem before, but recently it is that the motherboard battery they said above is out of power, just replace the battery.

There is an error in the CMOS setting of your motherboard, re-enter the settings, or the CMOS battery is dead, change the battery.

Have you ever encountered the phenomenon of pressing f1 or f2 when the computer is turned on, and you have solved such a problem in this way. Today we're going to teach you how to turn off this pesky F1 key.

What's the matter?

I don't know how to pretend to understand. When you play F1, don't play F1 but Delete key.

It's OK to change it inside.

It's hard to do it if you don't know English.

Set it automatically in CMOS. This could be the reason why your battery is dead.

Three possible causes of this:

1。Your computer has a floppy drive, which will be caused by the first boot time if it is set to a floppy drive, and the time will be set to the initial state after booting.

It's very inconvenient, just turn off the floppy drive, (the following will talk about the method of off) because there is a USB flash drive now, and the floppy drive is basically not used.

2。You unplug the console after shutting it down, so that's how it goes. Just don't pull it out next time. It's okay not to pull it out.3 The BIOS coin cell battery on the motherboard is dead.

There is no way, only to change the battery.

How to turn off the floppy drive: Reboot, press del into the BIOS, and use the arrow keys to select "Standard".

cmossetup, press enter, enter "standard."

CMOSSettup. In the "standard

CMOSSettup" interface, use the arrow keys to select the selected "DriveA", and use PGUP or PGDN to turn the page"to "none".

Press esc, press f10, press y, save exit.

Relatively simple and practical method).

You can try. I wish you a speedy solution.

You need to press the F1 key to enter the boot, mainly because the settings in the BIOS do not match the real hardware data, which can be divided into the following situations:

1. In fact, there is no floppy drive or the floppy drive is broken, but there is a floppy drive in the BIOS, which leads to pressing F1 to continue.

2. I originally hung two hard disks, and set them as dual hard disks in the BIOS, but later forgot to change the BIOS settings back when I removed one of them, which will also cause this problem.

3. If the motherboard battery is out of power, it will also cause data loss, which will cause this failure.

4. Reboot the system, enter the BIOS settings, and find that the floppy drive is set to, but in fact there is no floppy drive in the chassis, set this item to none, troubleshooting.

Detailed article.

Most of them are called to press F1 to turn on after the BIOS battery is dead, and you can buy a battery for 2 yuan.

The method is: press the DEL button on power, enter the BIOS settings, and select the first one"Basic settings", I didn't set the floopy one"disabel"It's okay to be invalid.

That's your biosy setting is wrong.,You press the del key to enter in the general boot.,And then press enter after the first top selection on the left and right.,Set the time.,It generally won't appear!

Just turn off the floppy drive detection from the BIOS.

Press Delete or F2 to enter the BIOS when booting up. Put floopy in one setting"disabel"That's it.

If you don't have a clear eye to see your BIOS settings, one of the dumbest ways to teach you is to return the motherboard BIOS to its factory state, and reset it.

Pressing the F1 prompt means that there has been a recent change to the hardware settings.

Just enter the first item in the coos.

There are a few numbers that that item.

Turn it off, and there will be no such prompt.

Bois who entered the motherboard turned off the floppy drive, press F10 to save and restart, and if it doesn't work, change the motherboard battery. Basically, the problem is solved.

The problem with the settings inside your BIOS, you set up"Non-disk scanning"!So press every time you enter"f1"to enter!

Your motherboard boots from the floppy drive by default, if you don't have a floppy drive installed, the system can't find it and prompts you to press F1 to continue. Removal method:

Power on -- press del -- enter BIOS -- standardCMOS

featuers--drive

a--set to "none" --f10--y--quit, if it still doesn't work, you have to change the motherboard battery.

Two reasons:

1. The motherboard battery is dead. Solution: Replace the motherboard battery.

2. The floppy drive is not shielded. Solution: Shielding floppy drives.

This is a biso issue. Just go in and set it up. Press F1 because the error is turned on, and if you don't want it, go into biso and turn it off.

Look at the motherboard instructions

1；DIMM tissue mismatch (128 bits) is recovered by F1.

2；It has a certain impact, but generally does not affect the use of computers.

3；There's no good way, you can brush the BIOS to try it, but if it doesn't work, you can only use it like this or use a single 4G

It's been five days, why hasn't anyone answered the point? It's generally not a memory issue. I think it's because the motherboard settings are not set properly.

That's all there is to bois. If you look at it slowly, you can see what it means, but there must be one item that is not set. If you think it's a memory problem, just borrow 2G or 4G and replace it.

If you think too much, it's not harmful to the computer. If the two channels are not the same batch, there will be instability. You can use the Prime 95 to take the test, and twenty minutes is enough (one hour if you are free).

If there is an error, it means that the computer is unstable and sometimes there is a problem. It is recommended to insert a single 4G strip. No mistakes, everyone is happy.

Are you an integrated graphics card, the biggest benefit of dual channels is the integrated display performance upgrade.

Buckle the battery, put it on, and after setting it up, remember to press F10 to confirm and save, if you don't press it, you won't save it.

With a single 4G should solve the problem.

F1 is a computer electronics no shop.

That's when the motherboard BIOS detects a problem, prompting you to press F1 to continue or press the DEL key to enter the BIOS settings, you can press the DEL key to enter the BIOS, change the detection of all problems to all problems without detection, after saving and exiting, it will no longer prompt an error and start directly.

To press f1 to start: There are several reasons:

1. The CMOS parameter settings are incorrect

Floppy drive: If the floppy drive is not detected, please check whether the data cable is connected, and then see if the settings in the BIOS are correct: check the settings of the boot sequence; In addition, if there is no floppy drive, it is directly shielded.

Keyboard: Some CMOS settings in the keyboard problem will also appear press F1 to boot the situation, the landlord to check it himself.

Memory: Disable Memory Verification.

2. Prompt for low BIOS battery - replace the battery.

3. Jumper setting problem - refer to the manual setting.

press f1 to resume

In addition, it may be a non-fatal hardware error that can be replaced with a check.

5.When the system boots, press and hold delkey to enter comsGenerally speaking, there is a floppy drive in the first one, which is to press the F1 key when starting, if you don't press F1, set it to desable.

The reason for this situation is that the CMAM chip is out of power, or the BIOS refresh fails, solve: after entering the BIOS, select Standard CMOS Features to enter, then select Halt On, and change the setting value to No Errors (any error detected, the system will not stop running) Personal opinion, for reference only!

In the past, computers used floppy drives.

The earliest system installation 98 is through the floppy disk and soft area to install, generally the floppy disk drive is removed (thought that there are now U disks), after the system boot, can not find the corresponding boot hardware, prompt whether to enter the system].

F1 ignores this hardware check.

Recheck to see if you've set up the light zone guide, but the light zone is broken again.

1. After booting, the computer always has to press F1 to enter the system normally, which is due to the aging of the motherboard battery, 2. After booting, the computer always has to press F1 to enter the system normally, and the repair method is to replace the CMOS battery (button) on the motherboard.

The computer boot report did not find the PS2 interface mouse and keyboard. The problem of pressing F1 is mostly caused by incorrect BIOS settings or dead BIOS battery, you can go to BIOS and press F9 to reset the settings.

The keyboard and mouse are not recognized, so make a new keyboard and mouse. Try it.

Cause of failure:

1.The motherboard battery is out of power, causing data loss and causing failure.

2.If the floppy drive in the computer is broken or there is no floppy drive in the computer at all, but the BIOS is set up with a floppy drive, it will cause a malfunction.

Solution:1Replace the motherboard battery, another way to judge that the motherboard battery is out of power is to enter the system to see if the system time is consistent with the real time, if it does not match, the motherboard battery is generally dead, so the battery must be replaced.

2.There are several problems with floppy drives, and there are several solutions, as follows:

The first way: reboot the system, go to the BIOS settings, if you find that the floppy drive is set, but there is no floppy drive, you need to replace the IDE secondary master auto with none.

The second type: after the computer is booted, press del to enter the motherboard BIOS, enter the boot startup item to set the boot boot sequence, and turn off the floppy drive to boot.

The third way: start the computer, press the DEL key to enter the main interface of the motherboard BIOS settings, select the "Advanced BIOS Features" setting item to enter, and then set the "Boot Up Floppy Seek" to "disabled", you can turn off the boot software detection function.