The boot stops on the motherboard logo screen

This problem is usually caused by the failure to load the hardware due to the damage of the motherboard BIOS...

The solution is:Turn on the keypad and press the del to enter the motherboard BIOS,If your motherboard has the option to automatically rewrite the BIOS,Just flash it directly,If not,You restore the motherboard to its default value,If you don't know this,Just take the battery on the motherboard and install it again,Try it first。。。

The detailed instructions for your motherboard are introduced.。。。

The statement upstairs is incorrect.,If the hard disk is broken, the picture shouldn't be the logo of the motherboard.。。。 And if the memory is broken, it won't start at all.。。。

It is estimated that there should be a problem with the data cable of the hard disk, and the motherboard can't find the data of the hard disk! That's what mine is.

There is a problem with the SATA cable.

You plug in the hardware one by one and then boot it up, no, you unplug the optical drive and restart it, it should be that the system can't find the optical drive.

Unplug the memory and wipe it, if you can enter the system, do a good job of killing the virus.

You can try discharging the motherboard! You can't get into it because the data is corrupted by a virus! You can drain the charge and go in!

1. Press "Delete" to enter the BIOS interface, and click "Exit" on the far right. Select "load setup defaults" from the upper and lower cursors.

2. Then press "F10" to save and exit, and restart the computer.

3. If the problem has not been solved, select the "boot" option on the left and right cursors.

4. Click to enter the "Boot Settings Configuration" option.

5. Use the up and down cursor keys to move to the "Full Screem Logo" option. Press "Enter", select "disabled", and confirm, and the problem is solved.

The computer boot has been stuck in the motherboard logo interface, indicating that the problem was found during the power-on self-test, and it needs to be checked one by one, and the problem can be entered normally after the problem is solved.

1. If you can't enter the system because the motherboard logo is displayed at boot, you need to restart and press the TAB button to skip the LOGO screen or press the DEL key continuously (F2 or other specified hotkeys for notebooks) to enter the CMOS setting interface, and turn off FullScreenLogoShow in the AdvancedBiosFeatures tab to see if the POST information can be displayed, and then determine the problem.

2. Under normal circumstances, according to the prompt information of the black screen and white characters on the screen, press the F1 key to skip the non-fatal error and start the computer directly, or press the del key to enter the CMOS, and then press F9 to load the predefined parameters or select LoadoptimizedDefaults (load the high-performance default) or LoadFail-SafeDefaults (load the fail-safe default), and then press F10 to save and exit the restart.

3. If the original CMOS parameters are not saved or the system time in CMOS is restored to the factory time after the shutdown and power off, it may be that the motherboard battery is invalid, and the battery needs to be replaced, and then load the predefined parameters and save them according to step 2.

4. If the above operations are invalid, it means that there is a problem with the hardware, generally due to poor contact of the memory due to oxidation, or the hard disk may be damaged due to poor connection or hard disk master boot record, you need to re-insert the memory or hard disk, or repair the hard disk master boot record, or reinstall the system or replace the hard disk.

Many people will encounter some problems when using the computer, that is, the computer stays in the motherboard interface when it is booted, and even the computer standby state stays in the motherboard interface, so how to solve the problem that the computer stays in the motherboard logo interface when the computer is booted?

1. Generally, it is a problem with BIOS settings, and we only need to find the corresponding settings to solve the problem. Press the BIOS boot button first, cover Pei Ru and then we can choose the Chinese mode, click on "Advanced Mode" at the bottom.

2. Click "Startup" in the BIOS menu bar, find "Wait to press the F1 button if there is an error in the buried", and select "Close" in the corresponding right option.

3. Press F10 to save, restart the computer, and the problem of staying on the motherboard logo will be solved.

The above is the solution I shared with you to stay in the motherboard logo interface for the boot of the electric and physical enlightenment, and those who need it can learn about it, I hope it can help you.