How to install the broken wire in the hegemon?

Take the original one apart and replace it with a new one in the original location, so that you can connect it to them.

If the smuggling is broken, then it may not be easy to install in the process of installation, but you can tie it together according to your actual situation.

If the division is broken, change it to a new one according to the original position and fix it for him, that is, you can take a picture when you take it, and then make sure it.

I don't know if you have such feelings, the bath bomb we have installed at home, if something fails, it is a particularly troublesome thing to want to change. Because the installation of bath bombs needs to be complemented by the integrated ceiling. Even the master of the installation said that the installation of this bath bomb is really troublesome.

I think if this is broken, you can directly buy an original one, and then reinstall it to try it and see if it looks like it?

In this case, if you want to install better, you must use professional techniques and follow the regular operation to better achieve the ideal effect.

Take a flashlight, buy a slightly larger straight-shank twist drill bit, and turn it! Does it cost to weld? Isn't the toilet burning? Get your own electric drill. Save money.

: The problem of broken wire has always been a serious problem in the wire cutting process. It halts machining and has to start from scratch, wastes a lot of man-hours, destroys the integrity of the machined surface, and increases the realization.

Oh, what is the reason why my medium wire is not turned on and the 3000 is similar to the broken wire? Is it because the middle button is broken?

1. The tightness of the molybdenum wire If the molybdenum wire is installed too loosely, the molybdenum wire will shake badly, which will not only cause the broken wire, but also directly affect the surface roughness of the workpiece due to the jitter of the molybdenum wire. But the molybdenum wire can not be installed too tightly, too tight internal stress increases, will also cause broken wire, so the molybdenum wire in the cutting process, its tightness should be appropriate, the newly installed molybdenum wire, to tighten the wire first and then process, the wire tightening force should not be too large. Molybdenum wire in processing one.

It may be that there is a short circuit in the line.

What should I do about this? I don't know how important this is, what are you? Lathe or how.

Well, what my total. Didn't turn on. I don't know what the reason is.

The chicken rib function of the outlet water disconnection of this electric water heater should be turned off in the settings, or solved by the outlet sensor, and the method of this type of electric water heater is different for different brands.

There are 12 branches, 15 branches, 18 branches, 21 branches, 24 branches, etc. According to the installation method, it can be divided into rooftop solar water heater and balcony solar water heater; According to the pressure of the water tank, it can be divided into pressure-bearing solar water heaters and non-pressure-bearing solar water heaters.

Air energy water heaters can be divided into two categories: fluorine circulation and water circulation according to the heating form, each with its own advantages and not exclusive to each other; Fluorine circulation machine is divided into: household balcony machine, exterior wall machine, kitchen machine, commercial gecko machine, attic machine; The water circulation machine can be divided into: household balcony machine, terrace machine, kitchen machine, commercial gecko machine, attic machine, engineering roof machine, ground machine.

Then short the micro switch used to realize the function of power-off of the water outlet.

The so-called "water outlet power off" function is actually a water flu responder installed on the hot water outlet pipeline of the water heater, which automatically controls the disconnection of relevant components on the power supply line when the water flow is sensed, so as to realize the power off function.

The protective function of this design is a kind of after-the-fact protection, and the real effect is very limited.

The current parameters of some materials should be twice as high as those of ordinary materials.

Whether it is the middle wire or the fast or slow wire is the same, the speed is fast and the wire will be broken, and the same as the turning tool and milling cutter, the speed is fast and the tool is broken. Because the speed is fast, there will be two problems: 1. The temperature rises; 2. The workpiece continues to move without being cut off or melted, and is broken by the resistance of the workpiece.

Let's see if you have enough voltage there.

I haven't used it though.

But since I installed a voltage regulator.

My fast-walking efficiency went up all at once.