How the UG widget navigator is set to the left

1. First of all, open the UG software and enter the modeling environment.

2. Click on the part navigator on the left side, it will be displayed, click a pin on the top, it will fix the part navigator there, otherwise, when we design the drawing, the part navigator will disappear.

3. In the part navigator, by clicking: Datum coordinate system, the coordinate system will be displayed in the drawing area, otherwise it will be hidden.

4. In the widget navigator area, click right-click - Column - Configuration to enter the widget navigator properties, where you can add options that need to be displayed, according to personal design needs, such as ticking in front of the layer, click OK, and the layer will be displayed above the widget navigator.

5. On the identification of the part navigator, right-click and select Cancel docking, the part navigator will be removed, and you can drag the position at will.

<>7. Open the file and you can see that the part navigator is set to the left, and the rendering is completed.

The specific steps are as follows:

1. First of all, open the UG and enter the modeling environment, as shown in the figure below, and then enter the next step.

2. Secondly, click on the part navigator on the left side, and it will be displayed. Clicking on the icon next to it will pin the part navigator there. Otherwise, when you design a drawing, the navigator disappears, as shown in the following image, and then proceeds to the next step.

3. Then, in its drop-down menu bar, click [Datum Coordinate System], the coordinate system will be displayed in the graphics area, otherwise it will be hidden, as shown in the following figure, and then enter the next step.

4. Then, in this area, click Right-Click Column-Configure to enter the Navigator Properties interface. Here you can add the options you want to display as needed. As shown in the image below, then proceed to the next step.

5. Then, on the navigator logo, right-click and select Cancel Dock, you can drag the position at will, as shown in the figure below, and then enter the next step.

6. Then, you can move to the right side as needed, if you want to restore to the original position, click on the arrow to return to the initial position on the left, as shown in the image below, and then go to the next step.

7. Finally, open the file, you can see that the part navigator is set to the left, as shown in the figure below. In this way, the problem is solved.

UG widget navigator + is full of entities+, how to turn it into concrete steps.

Hello, what is displayed in the UG part navigator is a list of entities, you need to convert the entities into specific steps, you can follow the steps below:1Select the entities that you want to convert.

2.In the UG interface, click the "Operation" menu and select the "Feature" command to open the featurer. 3.

In a featurer, you can convert solids to concrete steps, such as feature creation, cutting, drilling, chamfering, and so on. 4.Add or remove features as needed, and adjust feature parameters to meet specific machining requirements.

5.After setting the feature in the featurer, click the "Apply" or "OK" button to save and exit the featurer. 6.

In the UG interface, you can set the rubber shirt concealment according to the beam hall of the feature, and use the corresponding processing command to perform the collapse operation on the entity. It should be noted that the steps of converting the entity into a specific need to be set according to the specific processing requirements, and the characteristics of the processing technology and processing equipment need to be understood, and adjusted according to the actual situation. At the same time, it is also necessary to master the operation skills of UG and the use of the feature device in order to better carry out the processing operation.

Hello, I am happy to serve you and give you the following answers: The reason why the assembly navigator cannot move may be due to insufficient battery disturbance circle or battery damage, or it may be due to damage to the motor of the navigator or damage to the controller. Workaround:

1.Check the battery level: Check the battery level of the assembly navigator, if it is low, you can try to charge it, if the battery is damaged, you can try to replace it with a new battery.

2.Check the motor: Check the motor where the navigator is assembled, and if the motor is damaged, you can try replacing it with a new one.

3.Check the controller: Check the controller where the navigator is mounted, and if the controller is damaged, you can try replacing it with a new one.

Personal Tips:1Periodically check the battery level of the assembly navigator so that the battery is low and the assembly navigator cannot be moved.

2.Regularly inspect the motor and controller of the assembly navigator to avoid damage to the motor or Qingchun controller and the assembly navigator cannot be moved. 3.

If the assembly navigator cannot be moved, the battery level, motor, and controller should be checked as soon as possible so that the problem can be detected and resolved in time.

If you find something missing in the middle of the construction and part navigation in your installed UG NX software, you can try the following solutions:

1.Check Display Settings: Make sure your software display settings are correct.

You can check it out in the menu bar"view"or"Display"option, check if the desired navigation panel or parts list is enabled. You may need to adjust the workspace layout or display options to display the content you want.

2.Custom Navigator: UG NX generally allows Sailzen users to customize the content and layout of the navigator.

You can try looking for the relevant settings in the navigator settings or options to make sure that what you want is visible in the navigator. You may need to add or enable specific subassembly or construction options.

3.Update software version: If you are using an older version of UG NX, there may be some known issues or limitations. Consider upgrading to the latest version for better features and fixes for possible issues.

4.Refer to software documentation and tutorials: Consult UG NX's user manuals, help files, or official tutorials to learn how to customize and use the Navigator feature. These resources often provide detailed instructions and steps to help you solve the problem.

If you are still unable to resolve the issue, it is recommended that you contact UG NX's technical support team or community forums for professional help and guidance. They will be able to provide solutions for specific software versions and configurations.

Check the English help document that comes with ug, some shortcut keys are generally in the instructions, and you can use a translation tool to translate if you don't understand English at all.