Why do you stick 2 red copper wires on top of the tiles when building tiles?

Sticking 2 red copper wires on top of the tile greatly increases the firmness, and the tile will not fall off again.

The flue is hot and too dry, so it is indeed not suitable for tiling.

1. If you have to paste tiles, you can only lay a layer of heat insulation board (insulation board) on the flue first, and then hang the net with cement mortar, and then paste the tiles. In this way, the heat of the flue is greatly reduced, and the tiled layer is easy to stick to the tile through the hanging net.

2. Re-tiling on the original base layer, but the process of adding copper wire hanging on the back of the tile should be adopted. It's very simple, use a cutter to open an inverted "A" slot on the back edge of the tile, insert the copper wire into the slot, and glue the copper wire with marble glue. When the tiles are pasted with cement mortar, steel nails are driven into the wall and copper wires are tied to the steel nails to reinforce the tiles.

Bricklayers and workers all know this "quasi-dry hanging tile" process, which is very simple, but the firmness is greatly increased, and the tile will not fall off.

3. If the tile you paste on the flue is relatively large and heavy, it is recommended that you use the copper wire to hang at the same time, and then use the expansion screw reinforcement method on the front of the tile. When the tile has been hung on the wall, use glass rhinestone to punch holes on the surface of the tile, and then use 8 cm of internal rotation expansion bolts to reinforce, the top of the expansion bolt can go to the decoration material store to buy a suitable metal round cover buckle, beautiful and generous.

It's just that I'm afraid of falling off, this is the so-called semi-dry hanging.

Heavy brick on the wall with sealing tile binder, super bonding effect, easy construction, that is, brushing and pasting, low cost. Improve the bonding strength between ceramic tiles and stone and adhesive materials, and effectively solve the common problems of hollowing and falling off in ceramic tiles and stone pasting.

1. The function of copper wire is to fix large bricks and heavy bricks on the wall with copper wire; It is divided into two kinds: dry hanging and wet hanging, dry hanging is to hang it directly, and wet hanging needs to be hung dry and then poured cement between the gap between the tile and the wall.

Second, the construction method of vitrified bricks: the construction method generally has 4 kinds of dry paving, wet paste, dry hanging, and wet hanging.

1. Dry paving: It is to use cement paste to lay the bottom on the back of the tile, and use about 1:3 dry hard cement mortar below to level it.

2. Wet paste: It is directly paved with ordinary cement mortar, and now there is basically no need for wet paste, the quality is not guaranteed, and it is easy to hollow.

3. Dry hanging: It is to open a seam on one side of the plate, play an expansion screw on the wall, hang an eye-punched angle iron to make a beam, and then put the pendant in the crack of the stone opening, and then screw the pendant into the eye on the angle iron, and use marble glue to glue the place where the pendant is placed.

4. Wet hanging: It is to fix the position of the plate (generally smashing nails on the wall, tying copper wire to the nails, and fixing the other end of the copper wire on the stone, a board is generally two nails) and then pouring cement in the gap between the plate and the wall.

Forehead ......This can refer to why high-rise buildings should be reinforced inside.

It is likely that the tunnel tiling is to enhance the reflective effect in the tunnel, and try not to let the driver produce a black hole effect.

The tunnel is generally made of cement pavement, and the asphalt road is black, and the reflective effect of lifting and destroying is not good.

I don't know what's going on with the blue tiles.

Tile is used to increase the reflective effect and make the vision clear; The blue line is the water level warning line.

The blue line is the navigation line.

Leak it. - It should look like this.

For the sake of good looks (I guess).

There are two kinds of bonding between copper wire and floor tiles: flexible bonding and rigid bonding. In the case of unequal use, the copper wire can be bonded to the floor tile with structural adhesive bonding, and the copper wire at the bond is coiled into a disc shape, with a diameter of more than 2 cm, and after 24 hours, the glue can be used after curing. is for flexible bonding.

In a hurry, it can be bonded with two-component glue, and the copper wire processing is as above, and the bonding method is as above. It is for rigid bonding. The glue cures (30 minutes) and is ready to use.

I hope my answer can help you.

1.Caulk will be used in tile paving construction, and caulk cannot be added immediately after pasting. Wait until the end to fill in the caulk. If you don't add it early, it's easy to get dirty.

2.After the caulk is added, the part that sticks to the tile must be wiped off with a clean cotton yarn in time, otherwise the grout will stick to the tile and it will be difficult to wipe off.

Tile adhesive is mainly used in the decoration of the interior and exterior walls of buildings, basements and kitchens, plus another insulation system is to change the adhesion of tiles, and the strength is greater in the later stage.

In addition, the thickness of ceramic tile adhesive can be controlled at 2-4mm when it is practical, and the thickness of the paste is generally 15-30mm when it is practical.

In comparison, tile adhesives are not only used in small quantities, but also save costs.

Tile adhesive is commonly known as mastic. The main thing is to glue the tiles left and right. Generally, if you want to stain the reinforced concrete wall with bricks, you must use tile adhesive. Because the concrete wall is relatively smooth, if it is directly stained with cement mortar, it will cause the wall tiles to fall off. Hope to adopt!

The tile adhesive is high, the tile is relatively firm, not easy to fall off, and there will be no hollowing, but it is higher than cement. If the wall itself has a hairdressing treatment, you can consider using cement directly.

OK. To paste tiles on top of the original tiles, you can first use ceramic tile refurbishment putty to scrape twice, and then you can paste tiles according to the normal operation method.

Tile renovation putty is a two-component high adhesion putty, which has high adhesive strength on the surface of new and old tiles, and is a new generation of high-quality green building materials. It is made of acrylic emulsion, added with a variety of functional additives, mixed and mixed in proportion, and is used for the first level of interior and exterior wall tile renovation.

The surface of the tile is too smooth, it must not stick firmly with ordinary cement, it will fall off after a long time, and it is not resistant to moisture if it is used for engineering glue, so it is best not to paste tiles on top of the tile, if you must paste the glue will be better than cement.

Use tile adhesive, also called tile adhesive paste.