When decorating a new house, why is it becoming more and more popular to paste tiles?

The biggest project of a new house decoration should be tiling, because every corner of the room needs to be covered with tiles, and ceramic tiles are also a very good thing, because it can not only play a good aesthetic decorative effect on the interior, but also have a certain protective effect on the waterproofing of the wall and the ground. There are many ways to paste tiles, and sometimes if the tiles are not pasted well, it is easy to crack or fall or hollow after moving in.

In fact, there will be such a phenomenon of tiles, empty shares or falling, mainly because the traditional thick paste method was used to paste the tiles during the construction. In this way, the material used in the traditional post-paste method is mainly cement mortar, but there are certain limitations, these cement mortars are only suitable for some ceramic tiles with high water absorption, if it is said that the current thin ceramic tile is purchased, the water absorption rate is not so high, then its adhesion is very low and not durable. At this time, the tiles may fall and hollow in a short time.

This will add a lot of unnecessary troubles to our daily lives.

However, with the improvement of decoration requirements, and the various types of ceramic tiles are gradually increasing, some traditional tile tiling processes are no longer suitable for now. Now it is more important to choose the ceramic tile thin paste process, that is, the thin paste method. The thin paste method does not use a thick cement mortar, but a tile adhesive.

Tile adhesive itself is designed for tiling, so it will be better than cement mortar, and the adhesion is higher, and the thickness of the tile will be thinner, and it will save more space for the house with little space. andAnd the tile adhesive has a higher degree of adhesion, which can effectively avoid the phenomenon of tile hollowing and falling after the tile is pasted. That's why it's more popular to use thin stickers when decorating new homes.

The benefits of thin tiles: first, it can save space; Second, the weight of the wall is reduced, and the use time of tile decoration is prolonged; 3. Save decoration materials and decoration time.

Because thin tiles are now more popular. Whether it is from the perspective of ** or material and durability, thin tiles are the cost-effective one.

The thin paste method is becoming more and more popular, because if it is very thin, the surface will look particularly beautiful, and the natural overall decoration space also looks very clean and neat, so it is particularly popular.

If it is very thin, then the tile will be very firmly pasted, in this case, the tile will be close to it, giving people a special feeling.

Decoration wall tiles are not the thicker the better, the thickness is moderate, the appearance is beautiful, the solid wall tiles are better, after the paste is finished, pay attention to the maintenance of the wall tiles, do not use heavy objects or sharp objects to knock on the wall tiles.

Thicker tiles are not always better. Remember not to use a sharp shovel to clean it, but to use a sponge to clean the surface of the tile. The water absorption of ceramic tiles is relatively high, and the caulk may penetrate the tiles, so you need to use a professional tile cleaner.

It's not that the thicker the sticker, the better. After pasting, we must pay attention to check whether there is a hollow drum.

Decoration Da Cui explains the tile thin paste process, hoping to help you in decoration.

Faster and cheaper tile thinning.

The thickness of the paving is thinner and more environmentally friendly.

Old process: paving thickness in 15-20mm

The thickness of traditional cement mortar is about 15-20mm, because the cement itself has no adhesion, so it is necessary to let the tile absorb water to enhance the adhesion between the tile and the cement mortar. In modern design, special materials such as vitrified tiles and lightweight partition panels are increasingly used, and their water absorption, shrinkage and surface treatment have a very direct impact on the quality of ceramic tile paving.

New process: the thickness of paving is only 3-5mm

The surface paved by the thin paste method is usually only 3-5mm thick, and its materials have been strictly screened, because of the addition of high-performance additives, the tiles can be directly paved without soaking in water. Compared with the traditional method, the thin pasting process is more robust and durable, which can meet the individual requirements of different engineering nodes and special parts, and the amount of material is also very economical.

Old process: the site is seriously polluted, and the paving quality is unstable.

The construction method of ordinary yellow sand cement is not only dirty on site, but also the ratio and dosage of materials, whether the mixing is uniform depends entirely on the experience of the installation master, and the quality of tile paving is naturally uneven.

New process: ready-mixed dry-mix mortar is time-saving and environmentally friendly.

The use of ready-mixed dry-mixed mortar by thin paste method is a product with a good ratio in advance, as long as the water is added and stirred evenly according to the specified proportion, it saves on-site batching time, simplifies the construction steps, and the efficiency can be increased by more than 4 times compared with the traditional construction method.

Tile thin paste construction process.

1. Before stirring and preparing the binder, the tile should not be soaked in water, but the loose material on the back of the brick should be removed with a wire brush, and the floating dust on the back of the brick should be wiped off with a damp cloth. The water or emulsion is then placed in a mixing drum in the ratio recommended by the manufacturer and stirred until the binder is homogeneous and free of lumps. The binder after the initial stirring should sit in the mixing drum until the manufacturer's recommended curing time has elapsed.

2. Use the straight edge of the toothed spatula that meets the required thickness of the adhesive layer to batch the stirred adhesive to the base surface, and comb the adhesive layer into uniform strips along the direction of the tile joint. The purpose is to control the thickness and amount of adhesive and to make the tile area more uniform.

3. Before paving the tiles, a thin layer of adhesive is also batched on the back of the tiles. Although this two-batch method uses a lot of materials and man-hours, it can ensure the quality and durability of the paste.

Fourth, the tiles are laid in place during the bonding dose drying time, and the prepared tiles are paved in place, and the air under the bricks is slightly rubbed perpendicular to the combing direction. After the paving is in place, tap it with a rubber hammer and adjust the flatness of the surface and the straightness of the seams with a cross positioning frame of appropriate size.

5. Clean up in a timely manner.

The laid brick surface should be cleaned in time, especially to remove the adhesive remaining on it. After the qualified binder is dry and hardened, it is not easy to be removed even on the ceramic tile surface. Cleaned tile surfaces should be immediately marked to isolate them from contamination or disturbance until the next caulking process.

Thin paste method is a new type of pasting ceramic tile process originated in Germany, with special tile adhesive and tooth scraper, on the construction base surface of the tile adhesive comb scraped into stripes, and then in order to paste the tile on the cement, using the dry work paste method of kneading and squeezing positioning.

1. Comparison of the advantages and disadvantages of the thin pasting method and the traditional method.

Thin paste process:

The unit adhesive dosage is small, and the coating is thin, only 3 kg m

A few days ago, I went to the community and found that my neighbor's house was being renovated, and I wanted to go in and have a look, and found that my neighbor's house was all tiled. I thought that my neighbor had really spent a lot of money to renovate the house, but after talking to the neighbor, I realized that it was a project given by the decoration company.

This is the site of the balcony tiling. This is really a big project, I see that the master's craftsmanship is good, and he is very serious. This is the method of dry-laying tiles, which makes it more solid.

Level the ground before tiling. The next step is to apply cement mortar, which can be better bonded.

Cement mortar not only has the effect of bonding, but also makes the tile stronger.

When pasting tiles, you must leave gaps, and you must do beautiful seams in the future.

Once the tiles are attached, hit them with a hammer.

After pasting, don't forget to knock each one through.

Look at the tiles on the wall.

It's the restaurant and the whole house is tiled all over.

This is the effect of the bathroom. This is the bathroom wall tile, look at the master's craftsmanship, really good.

A partition is also designed here, which is very convenient and practical to use in the future.

Comparison of the thin tile application method with the traditional application method.