New computer, 2 16G computer boots up normally, and then add a 2 16G boot no response?

Gigabyte Z370 HD3 Max Memory Capacity: 64GB Support Dual Channel DDR4 4000 (

This is usually due to incompatibilities between memory. When using multiple pieces of memory, try to select memory with the same parameters and brand, or similar to each other.

It should be that how much he adds to the computer has nothing to do with his memory sticks and the computer, in fact, it is a memory stick that keeps memory, and it should be that one of your memory sticks is broken. He may cause the entire memory module to fail detection.

Explain that your computer can only support one 46GB memory

Swap out the memory for the previous one.

There is a memory that is not enabled. Memory dual channel is 1 and 3 2 and 4 interpolation.

Is there a memory limit set? If you set it up, you can only use 8G

The computer memory is capped at 8g, one is enough!

The next new version of the CPU-Z tool looks at the memory identification and whether the motherboard has a new BIOS

This is because in the system.

There is no setting in the come, since.

You can set zhi in the system according to the next steps of bai, and the memory dao will display normal after setting.

Tool: Computer.

1. Right-click [Start] in the lower left corner of the system desktop, and click [Run] in the start menu.

2. Enter [msconfig] in the run dialog box, click OK or press Enter to open the system configuration window.

3. Click [Guide] in the upper toolbar on the current interface.

4. Click [Advanced Options (V)] on the left side of the current interface, and then click OK.

5. Click on the small square in front of the maximum memory in the bootstrap advanced options window that opens.

6. Change the value to the maximum value of the installed memory, 8G input, 16G input.

7. Click [Apply] at the bottom of the interface, and then click [OK].

8. Click [Restart], and the memory will return to normal after the computer restarts.

Here's how:

1.Open the "Run" dialog box, enter msconfig, and enter the settings;

2.Select the "Boot" tab and select "Advanced Options" to enter the Boot Advanced Options.

3.Tick "Maximum Memory" to save and restart;

4.If it doesn't work, go to "System Settings" again, remove the "Maximum Memory" and "Number of Processors" options, and restart it again.

5.At this time, if there are still a few hundred megabytes, turn on the computer and press del to enter the BIOS, find "memoryremapteature", and enable it.

1. All If the boot is normal, the continuous use is normal, and only the system cannot be woken up after standby, then it is generally not a memory problem, but a system or driver problem.

If you don't use it for a long time, the system will enter sleep mode. If the hardware driver is faulty and cannot work with the system, it may crash when it sleeps or wakes up.

Use the driver version released on the manufacturer's official website for all drivers, and if you can't reinstall the system, you should be able to solve the problem.

In this case, it should be that there is a problem with your memory module, and there is an incompatibility situation, you can test it one by one, and you will know which one has the problem.

Hello, are you there? Maybe I can solve your problem!

What's so strange about this is that if the electrocopy brain wants to run, it must occupy memory, and the moment the system starts, DU will occupy it.

The amount of memory occupied depends on the needs of the software and hardware DAO.

In addition, the memory capacity is limited by the system, this can be clicked to run, enter msconfig, and then boot - advanced options - and then check the maximum memory, and finally confirm that the restart is OK.

Advice: Now some memory quality and capacity have shrunk, so when buying memory, try to go to a regular platform to buy brand strips!

Computer memory, 16G memory (8G * 2 memory stick), if the onboard graphics card will occupy a part of the memory, so the available memory will be less than 16G.

The base system of the two is not the same, and the default advance rate of the copy computer is 1024. And the manufacturer is 1000. Based on this calculation, the 3rd power of 1000 divided by the 3rd power of 1024 is about 14*, which is about equal to about 10%, and the difference within 10% of the same capacity is purely normal, so 16g is only more than 14g.

Because of the computer and hand bai machine memory meter

The calculation method is different from the computing DAO method of hardware manufacturer's memory. The phone I usually use is back to memory.

Answer: 1m=1024kb, 1k=1024b, this is because the mobile phone is calculated in binary, and we commonly use the decimal calculation method, which should be 1m=1000kb 1k=1000b, when the manufacturer manufactures the memory, in order to facilitate the calculation, it uses the decimal calculation method, so there is a gap between the actual memory and the memory we see, which is the reason why the 16G memory module is a few Gs less.

The system is a software.,The system will start when it's turned on.,The system will occupy memory.,And then there's a drive that needs to be started.,What adds up to the memory that needs to be occupied after booting.。

It's been used! The relationship between the detection data to 1 decimal place is normal.

Generally speaking, it's because it's occupied by hardware such as graphics cards.,But you have a separate display.,Other devices shouldn't account for 2G.,It's recommended to go into BIOS or PE to take a look.。

This is normal, the manufacturer's 1G is 1000MB, and the computer's 1G is 1024MB, which is caused by the calculation methods of the two.

It is estimated that you are using a core graphics card, and the graphics card consumes a part of the memory.

It's normal to take up when you turn it on.,Unless it's turned off and not turned on.,The memory is full.,You can't see the data if you don't turn it on.,It's meaningless!

You buy a 120-square-meter house with 120 square meters, the system, graphics card, etc. to occupy.

The system boot will account for a part, install this software to optimize memory: intelligent memory release wizard.

Z270-A This motherboard is a 4-slot motherboard, if you are plugged in 2 8G memory should be empty 2 slots, directly buy 1 16G memory plugged in to increase to 32G.

This is a single channel, not a single bar, and it has been identified to 32g. You can try to change one of them to another slot.

Normally, your computer recognizes 32g. Turn on my computer. The right-click properties are the amount of available memory recognized by the computer motherboard.

Brother, has this problem been solved? I'm also a problem, and I can't get it right for a long time.

Typical memory incompatibility,Generally two memory incompatible,The landlord can try to insert only 4G memory to try,If it can start normally,Stable use means that there is no problem with the memory,It is caused by the incompatibility of the two memory,The memory group dual channel is best the same brand with the same parameters,But generally different brands of different capacities can also be used stably,But there is a chance of compatibility,The landlord can change the memory!

The memory module type matching, or the main frequency of the memory module you change is too high, and the motherboard does not support it!

Try it separately, maybe there is a problem with one of them, or try to change the slot.

If your current 16G is not satisfied, there will be no improvement, if the memory bottleneck is added, you can try it.

You can't use those, so there will be basically no improvement.