Can you tell me about the purpose of the level? Be more detailed, thank you

The level is used for inspection, measurement, marking, equipment installation, and construction of industrial engineering.

Characteristics of the level Light weight, less than 2 meters, more than 2 meters 3kg m. A 6-meter-long ruler weighs only 18 kilograms and can be used by one person. Not easy to deform:

Generally, the bending point of steel material is 30kg mm2, the bending point of iron castings is 38kg mm2, and the magnesium-aluminum alloy reaches 110kg mm2, which is equivalent to 3-4 times, which has the effect of anti-bending and not easy to deform. The level bar has a horizontal bubble, which can be used for inspection, measurement, and debugging whether the equipment is installed horizontally.

If you want to buy, it is best to go to the CLW8 level, where there are many varieties of level tools and the quality is more reliable.

The purpose of the level: it is mainly used to check the straightness of the guide rails of various machine tools and other equipment, and the tools used to measure the level of equipment installation, inspection, measurement, marking, and industrial engineering construction. It can also check the small inclination.

The production level starts with pressing the wooden strips. First of all, use a grooving machine to dig five holes in it, three of which will be filled with horizontal bubbles with bubbles, and the other two holes will be used as sleepers. After the hole is made, the burrs on the edges of the strips are also removed, and grooves are cut out at the edges so that they can be filled with gay champagne.

Then the copper strip used for trimming is pulled to the forming machine, the curved copper strip is rolled flat and straightened by rollers, and then the copper strip is folded out of the specified shape, so that it can be close to the groove of the horizontal wooden strip. The copper edging is then placed on the machine, which inserts them into the groove to strengthen the edges of the entire strip.

First prepare the birch strips and drill holes in the birch strips. Then inlay copper edges along the wooden strips. Use rollers to shape the steel bars, put wooden blocks into them, make small bottles, and then pour mineral oil into the small bottles with the mouth facing up, leaving space for bubbles to form, and seal the plastic lid.

There is a swimming blister in the middle of the glass tube, put the level on the measured object, the blister of the level deviates to which side, indicating that the side is higher, that is, you need to lower the height of the side, or increase the height of the opposite side, and adjust the blister to the center, which means that the measured object is horizontal in that direction. As a general rule, both horizontal and vertical are in the center, and angled blisters are naturally in the center.

There is a round blister in the middle of the level, if it is centered, it indicates that it is horizontal, and if the blister is shifted to the left, it indicates that the left side is low....

In the middle of the bubble, is horizontal. The bubbles are to the left, and the bubbles are high to the left. The bubbles are to the right, and the bubbles are high to the right.

Place the bottom edge of the triangle plate vertically against the surface of the object to be measured. If the surface of the object to be measured is level, then the hammer line will coincide with the zero scale mark of the protractor; If the surface of the object to be measured is not level, then the angle indicated by the hammer line on the protractor is equal to the slope angle of the surface of the object to be measured.

The level is a measuring instrument that uses the principle of liquid level to directly display the angular displacement with the level bubble and measure the deviation of the relative horizontal position, plumb position and inclined position of the measured surface.

The level can be used for short-distance measurement, and can be used for long-distance measurement, and also solves the shortcomings that the existing level can only measure in the open place, and the narrow place is difficult to measure, and the measurement is accurate, the cost is low, the carrying is convenient, and the economy is applicable.

If conditions permit, buy a digital display level, it will be much more convenient to detect and adjust. Check it out.

There is a bubble in the middle of the level, just keep the bubble centered when using it.

How is the level used? Thank you.

The level is a measuring instrument that uses the principle of liquid level level, and uses the level bubble to directly display the angular displacement, and measure the deviation degree of the relative level, plumb and tilt position of the measured surface. The level is mainly used to detect or measure the straightness of the horizontal level, which can be divided into aluminum alloy square tube type, I-shaped type, die-casting type, plastic type, special-shaped and other standards; Lengths from 10cm to 250cm are more than standard.

Before using the level, we first need to check its usability to see if there are defects such as cracks and porosity on the surface of the level, whether the liquid in the level is clean and transparent, etc. Once we have determined that the level is ready for use, we calibrate it. Calibrating the level is simple:

Put the level flat against the wall, draw a line on the wall along the edge of the ruler, and then swap the left and right ends of the level, and put it on the original drawn line.

The level generally has three glass tubes, each with a bubble in it. Place the level on the object to be measured, which side the bubble of the level is biased towards, it means that the side is higher, and the height of the side needs to be lowered, or the height of the opposite side needs to be increased; If the blister is in the center, it means that the object is horizontal in that direction. The horizontal glass tube in the level is used to measure the horizontal plane, the vertical glass tube is used to measure the vertical plane, and the other is used to measure the angle of 45 degrees.

In addition, the principle of determining a plane based on two intersecting lines requires measurements in two non-parallel positions within the same plane to determine the level of the plane.

The level is very easy to store and will not affect its straightness and parallelism due to the long-term flattening. Therefore, it can be hung somewhere or placed flat on the table or drawer. During use, the level does not need to be oiled, if it is not used for a long time, it can be coated with a thin layer of general industrial oil when it is stored.

Levels are available for sale.

How to use the level, let's take a look at the friends who haven't seen the level and can't use it.

How to use the level: place the bottom edge of the triangle plate vertically against the surface of the measured object, if the surface of the measured object is horizontal, then the hammer line will coincide with the zero scale mark of the protractor; If the surface of the object to be measured is not level, then the angle indicated by the hammer line on the protractor is equal to the slope angle of the surface of the object to be measured.

Beijing Million Electronic Technology Center is a large-scale instrument manufacturer and seller, the business areas mainly include: gas detectors, metal detectors, environmental protection equipment, health care, laboratory instruments, chemical equipment, agricultural instruments, mechanical and electrical equipment, fire and security equipment, power communication equipment and other almost all industries. The company's product LS160 digital level can carry out angle measurement in a 360° range, which is easy to use, fast and accurate, and is an ideal tool for equipment installation and angle measurement.

A level is a tool used to measure the direction of horizontal high bumps. It usually consists of a ruler and a bubble tube. When taking the measurement, the level should be placed on the horizontal plane to be measured, and its position and orientation should be adjusted until the bubble in the bubble tube is in the ** position.

When the bubble is in the ** position, it means that the position of the level is horizontal.

Levels are commonly used in construction and manufacturing to ensure that buildings and manufactured goods are level. In construction, levels are often used to measure the levelness of floors and walls. In the manufacturing industry, levels are often used to measure the levelness of machine components.

There are a few things to keep in mind when using a level for measurements:

1.Make sure that the surface of the level is free of any impurities or dirt. These substances may affect the accuracy of the measurement.

2.Make sure the position and orientation of the level is correct. If the position and orientation of the level are incorrect, the bubbles in the bubble tube will not be in the ** position, resulting in an inaccurate measurement.

3.Make sure the bubbles in the bubble tube are in the ** position. If the bubbles in the bubble tube are not in the ** position, you need to adjust the position and direction of the horizontal ruler until the bubbles are in the ** position.

4.Make sure the length of the level is long enough to cover the area that needs to be measured. If the length of the level is insufficient, it will be necessary to take multiple measurements and calculate the average.

In conclusion, a level is a simple yet effective tool for measuring the horizontal direction. There are a few details that need to be taken care of when measuring with a level to ensure that the measurement results are accurate.