What should I do if the psp is flooded, the PSP is flooded, and I can t store things after repairing

In this case, don't turn on the machine yourself, it may lead to burn-in, but it doesn't matter when the water is all dry and it is opened, there is a certain probability that it will be fine, my GBA was like this back then, the whole fell into the water, and then I dried it in the sun, and everything was normal when I turned it on. Hehe.

Go to the place where you buy PSP to disassemble it, such a situation generally can't be recovered, if you're lucky, the boss wipes it with alcohol, maybe it's good, if it's bad luck... Sell your PSP and buy a 3000 and other cracks...

Is your machine 1000 or 2000?The 1000 keys are made of conductive rubber, and the keys do not respond because they bring in dirt after entering the water, and the water is slightly dry and left under the glue and stuck, which must be disassembled and cleaned. The conductive sheet used for the 2000 button, the directional key is a common conductive piece, which may cause a short circuit in the cable interface after water ingress, resulting in failure, and the machine needs to be cleaned as well, and the conductive sheet must be replaced if you are unlucky, and dozens of dollars are indispensable.

Don't turn on the machine for the time being, put the machine upside down in a dry and ventilated place with the best sun for a week, turn it often, make sure that the water is dry and then turn on the machine to see the situation, if you don't recover, you must disassemble the machine.

1.If you don't want to repair it, you should wait at least 5 days before turning it on, because the water on the internal circuit board has not completely dried. When the stagnant water dries up, the function of the PSP will gradually recover.

2.You can't use a hair dryer every day to blow it, it will hurt PSP.

3.Put the PSP upright and let the water inside stay down. Open the UMD bin of the PSP and place it in a ventilated place.

The warehouse is a good seat for blowing, and when you blow with a hair dryer, you blow from there.

If some symptoms appear at that time, it is inevitable, but it really can't be done, so I have to take it to the video game store where you bought PSP to fix it. The cost of repair depends on the specific situation, the general key part is cheap, 50 can be used, if the circuit board is broken, it can cost 2, 3 hundred. Watch him fix it when repairing it to prevent him from changing parts.

Hello, to the after-sales testing and processing, there is no way for artificial. Don't panic when your electronic devices get into the water. We divide the situation into 3 types:

1. Fall into clean water when the power is on; 2. Falling into non-corrosive liquids in the case of power failure; 3. Falling into non-clean water when the power is on, or falling into corrosive liquid or viscous liquid or other clean liquids regardless of whether the power is on or not.

The first two cases have a good chance of being saved and there may be no sequelae, while the latter depends on luck. Of course, if you are unlucky, PPC will also be bad if you put it in your pocket.

The biggest problem after PPC water ingress is how to deal with it. First of all, for the 1st and 2nd cases, we must not think that the machine has been scrapped. Don't think it's already in the water anyway, so you disassemble it indiscriminately. Here are some suggestions for each situation:

1. Drop into clean water when the power is on, this situation generally does not need to be disassembled.

1. Power off as soon as possible.

2. Shake dry vigorously (depending on the situation, if you pick up the phone immediately after falling into the water, you can consider not throwing it dry), but don't shake off the machine, the idea is to shake out the water in the screen. If there are water droplets left on the screen, there will be traces after drying.

3. Put it under a slight heat source such as a table lamp and spotlight to let the moisture slowly dissipate. This process takes more than six hours. Do not use a strong heat source such as a hair dryer in a hurry.

4. If there is something left on the screen and it is very serious, do not deal with it according to the first point and paragraph 3, because although the electronic circuit after this treatment can work normally, the screen may be quite ugly. It can be sent to the nearest maintenance department for processing or dismantling the machine for cleaning by yourself.