How to cut the card of the apple 5, how to cut the card of the iphone5s?

The card is very special, and the previous micro-SIM card could not make a nano-SIM card by cutting the card at all. If you want to use the iPhone 5, you have to wait until domestic telecom operators launch dedicated nano-SIM cards.

2.After putting the nano-SIM card on the old version of the micro-sim, we found that the width of the metal strips of the two cards is actually the same, but the height is a little different. Note that this is an older version of the commercially available micro-SIM (a new version of hair cutting will be introduced later).

3.It's easy to do at first, just cut off the plastic edges along the bottom of the metal strip of the old Micro-SIM card. Then cut off the plastic edge along the right edge of the metal strip of the old micro-SIM card.

4.**The lowest point, cut off the excess horizontally, here will cut off a part of the metal strip, but don't be afraid, it has no effect on the card, and then, cut off the corners diagonally to the upper right. Finally, grind the back of the cut card slightly.

5.We turned the metal strip over, and it turned out that there would be chip contacts within the red dotted line, which means that the part we just cut out was not the chip part at all.

6.At present, how did the more common new version of Unicom's micro-SIM card become a nano-SIM card, let's first put the two cards horizontally together to see, it turns out that the height of their metal strips is basically flat.

7.Then, we put the nano-SIM card on the new micro-SIM card and align their left and bottom edges. At this point, it only takes a few simple steps.

The steps are actually similar to the steps of the old version of the card cutting above, just grind the back a little after cutting. Load the cut Nano-SIM card into your iPhone 5, and a signal appears to indicate that it is finished.

Lessons learned.

Buying a card cutter is simple.

You can use the card needle and card cutter that come with the iPhone.

How to do it: Insert the card pin vertically into the small hole under the SIM card slot on the right side of the phone.

Suspicion of this Tong Han.

With a little force, you can eject the SIM card slot.

Finally, use the card cutter to cut the large SIM card into a small card, put the cut card into the card slot, and then install the card slot back.

iPhone5 Card Cutting Method:

Materials required: a pair of ordinary scissors, a mobile or Unicom ** card, and a ruler.

iPhone5 Clipping Steps:

Observe the difference between a regular SIM card and a micro SIM card, and find out the center point of the metal contacts of the SIM card.

The left is a regular SIM card, and the right is a standard micro SIM card.

Measure the center point of the metal contact part of the micro SIM card by measuring it with a ruler and mark it with a pencil.

Use a ruler and pencil to draw the center point of the contact.

Measure finely with a ruler, and measure the distance between the two sides by the center point of 7mm and 8mm respectively.

The distance from the center point to both sides is measured laterally.

Then measure the distance from the center point to both sides longitudinally, about 5mm on the left and 7mm on the right, and try to control the error as much as possible.

The distance from the center point to both sides is measured longitudinally.

Next, put the notches of the two SIM cards in one direction, and then use the same way to find the center of the contact on the regular SIM card, and pay attention to the balance line.

Compare the balance lines of the two cards.

Overlap the nano-SIM card with the regular card, and carefully observe whether the position of the center point and the position of the parallel line are consistent.

Compare the two cards that coincide.

The preparation is completed, the next step is to cut the card, don't rush when cutting the card, take your time to be steady, otherwise you may scrap the card if you are not careful.

Finally, the cut-out finished product is compared with the original micro SIM card.

If you cut to the metal contacts during the cutting process, don't be afraid, there is no effect. However, there must be a curvature in the corner processing, and the responsible will not be able to be placed in the iphone5 card tray.

Go to the business hall and cut the card for you for free.

Light cutting is not good, but it is better to go directly to a 5 special SIM card and ask: Is it a nono SIM card?

The ** card of the iphone 4s is smaller than the general mobile phone card, and the ** card of the iphone s is smaller than the ** card of the 4s, therefore, the ** card of the iphone 5s can be cut with the general large card or the small card on the 4s.

1. Since China Mobile, China Unicom, China Telecom and other sellers are free to cut (change cards), you can go to the corresponding seller's business hall and ask them to help you cut (change cards).

Second, if you want to cut it yourself, it is best to find an apple 5 Kirby, use a pencil to draw the cutting edge first, and use a paper cutter to slowly draw it (better than using scissors), pay attention to light, slow, do not scratch the rest of the circuit board.

The mobile phone store has a special card cutter, it is not recommended to cut it yourself, it is easy to cut it.

Take it to a mobile phone store and ask someone to cut it for you or buy a card cutter yourself.

Go to your carrier where you can change the small card for free.

According to your current card cutting situation, the metal range is not damaged This card is completely usable, but it lacks the fixation and adjustment of the plastic part, and it is inevitable that the signal will be unstable or unusable, it is recommended to change to a new card, so as not to delay the big thing, what do you say?

The Apple 5 card is smaller than the one you pictured, so you can cut it yourself.

You see my self cut like this, and it works just as well.

If you can't find it, you take off the shelf where the Apple 5 side card is installed, use a piece of tissue paper to lay flat on the beveled side, press out the print along the edge with your hand, use scissors to cut out the card size (card mold) along the paper print, use this paper card mold to be cut in the middle of the chip of the card to be cut, draw the cutting line with a pencil, and slowly draw it with a paper cutter (the paper cutter is not easy to break the card), mark slowly, don't scratch the circuit board.

In addition, with the ID card at the time of card registration, you can change the card and cut the card for free at the business hall.

You're stupid, you look at me and laugh, how can you use this, you're making up a card.

It works that way, too. Just put it on the other side. I cut all my cards with scissors.

Landlord, I'm sorry, I was stolen a few days ago, and I sent some garbage propaganda, please ignore me.

In addition, I'm culturally classified, so I'll compensate you for some **.

Yes, you need to have a card cutter.