What are some tips for using glass glue?

Our house has just been renovated this year, and when it was renovated, it was also found by its own family, and the whole process was seen at the scene, especially when playing glass glue, some small tricks should be used, and the left hand controls the glass glue gun nozzle. Be sure to keep the mouth-grabbing collar close to the gap and not swaying back and forth. Adjust your breathing, don't exhale and breathe in heavily, keep breathing in small increments, or even hold your breath for a short time, so that your upper body doesn't shake too much because of your breathing.

It is best to glue in one go, in one direction without multiple pauses.

Depending on the width of the gap you are making glass glue, cut the nozzle into a slightly smaller diameter than the gap. Do a good job of protecting both sides of the gap between the glass glue, and paste 2-3cm adhesive tape on the glass, profile, stone, etc. on both sides of the gap, which plays a protective role in the glass, profile, stone, etc., and also has great convenience for correcting the glue in the gap. Master the speed of glass glue and the speed of the movement of the glue gun, move the glue gun evenly according to the depth of the gap, master the speed of the glass glue and the speed of the glue gun movement, and move the glue gun evenly according to the depth of the gap.

Cover the surface near the connector with plastic tape. To ensure that the working lines of the seal are perfect and neat. Cut the nozzle of the hose, attach the needle-nosed tube, and cut it at a 45° angle according to the size of the caulking.

Install the glue applicator and keep the rubber material pressed out along the gap at a 45° angle to ensure that the rubber material is in close contact with the surface of the substrate. When the seam width is greater than 15 mm, it is necessary to apply the glue several times. After gluing, trim the surface with a knife, remove the excess rubber, and then tear off the tape, if there is a stain, you can use a damp cloth to remove it.

Home decoration is a very troublesome thing, decoration is not only the big aspects, some small details should also be paid special attention to. Use a lighter to bake the nozzle of the glass glue until soft, and then pinch the nozzle of the glass glue flat. Nozzle of glass glue, cut at an angle of 45 degrees with a knife; Align the nozzle with the position where the glass glue needs to be applied.

Nozzle of glass glue, cut at an angle of 45 degrees with a knife; Align the nozzle with the position where the glass glue needs to be applied. Firmly pull the trigger of the applicator gun to inject the glue to the desired position.

In the past, my family would often use glass glue when decorating the house, and when hitting doors and windows, it was necessary to use a little trick, the most important thing is to hold the glass glue gun trigger with the right hand, and the force of extruding the glass glue must be even. It is necessary to use what we usually call resistance, that is, to maintain a certain amount of strength. But the strength can't be hit for a while and a little bit.

Because usually the glass glue is relatively large and spherical when it is just squeezed out of the nozzle, if the piece is large and small, it can only be smoothed by the method of smearing.

The use of glass glue must have a small trick to play well, must be steady, pre-calibrate the distance of movement, as far as possible do not move too much, and appropriately spread the legs a little. In this way, you can ensure that you can use the upper body to translate or turn the waist and work hard to squeeze out the straight line of the glass glue. If you walk too much.

It will affect the stability of the extruded glass glue.

Some adhesives will be used in decoration, among which glass glue is the most commonly used, glass glue is not only used when sticking glass, but also can be used to stick some wooden or stainless steel items. The use of glass glue is not particularly good for ordinary people, remove moisture, grease, dust and other pollutants on the surface of the joint, and use solvents (such as xylene, butanone) to clean the surface when appropriate, and then wipe all residues with a clean rag to make it fully clean and dry.

The surface of the sealant cures after 10 minutes at room temperature, and it takes 24 hours or more for the sealant to be completely cured, depending on the thickness of the glue applied and the temperature and humidity of the environment. First of all, you will need to be able to use a glass glue gun. Determine the width of the glass glue, that is, the width of the gap, so that you can use the glass glue correctly.

Step Method.

Start by preparing a jar of glass glue, a glue gun, and a knife.

First of all, we cut off the head of the glass glue that we bought, and when we bought it, he would give you a glass glue and a long head that was screwed into the glass glue, and the heads of both of them had to be cut off.

Then take out the glue gun, pull the handle in the picture below outward, then put in the glass glue and push the handle in until you can't push it.

Finally, press the handle in the picture below, and you can extrude the glass glue.

You also have to have a glass glue gun to propulsion, otherwise you don't have the strength to squeeze it out and apply it evenly on the seam.

Open the tip of the tip and put it on the glue gun!

It is necessary to open the pointed part and use it with a glue gun.

1. Press the switch on the back of the glue gun with one hand, and pull out the bolt with the other hand;

2. Use scissors to cut the glue outlet on the top of the glass glue;

Don't cut the threads when cutting;

3. Screw the glass glue nozzle onto the cut glue outlet;

4. Put the glass glue with the glue nozzle screwed flat into the glue gun;

Press the switch on the back of the glue gun, push the bolt forward, and fix the glass hose;

5. Align the nozzle with the position where the glass glue needs to be beaten;

Firmly pull the trigger of the applicator gun to inject the glue to the desired position.

6. Finally, use a scraper to scrape the beaten glass glue flat and modify it evenly;

After the glass glue is beaten, it generally takes 1 hour for the surface to be polished; 24 hours to dry; During this period, it is best to use other methods to secure the relevant object and not shake it;

Attach the glass glue to the applicator and apply it to the object you need to glue (be sure to clean the item) and press it down and wait for a while before you are done.

Put the pointed end on.

The glue gun on top will be fine.

Lift the toilet and pour the water inside, and then align the eyes under the toilet with the drain pipe of the floor drain, which generally leaks outward, just because the eyes are not aligned! My family used to leak water, with glass glue, right several times, hit the glass glue several times or leak, and finally got angry, directly with cement thick seal circle! This is not leaking, but you can do without cement, try not to use cement!

Glass glue is divided into: acidic neutral, generally selected at home, so that the taste is less and the corrosion is light. For example, if you stick to the mirror, you must use neutral, otherwise you will spend a lot of face.

It is generally used to assist in bonding and filling gaps. The glue gun is an iron frame with a screw handle, the glass glue bucket is installed, tightened from the back, and the front can be the basic glue.

Glass glue is generally divided into acidic and neutral, transparent glass is bonded with acidic a little stronger, but it is not acidic, acidic glass glue has a certain corrosiveness, and the mercury on the bottom surface of the mirror is afraid of acid corrosion. So use neutral. The glass glue generally takes 6-12 hours to dry, so you must fix the glass or other things you want to stick to after the glass glue is applied, with tape paper or temporary fixings.

There are many colors of glass glue, so you can choose according to your needs.

1.Make sure the surface is clean: Before using glass glue, it is essential to ensure that the surface to be bonded is clean and dust-free. Surfaces can be wiped down with detergent or alcohol to ensure they are clean.

1.Avoid over-extrusion: When using glass glue, do not extrude too much to avoid waste. At the same time, over-extrusion can also lead to poor bonding.

3.Make sure the temperature is right: Before using glass glue, you must make sure that the ambient temperature is right. Generally speaking, the best temperature for glass glue is 20 -25 .

3.Avoid over-fixing: When fixing the adhesive material, do not over-fix, so as not to affect the bonding effect of the glass glue.

1.Extrusion of glass glue tease block: Extrude glass glue onto the surface to be bonded. You can adjust the amount of extrusion as needed, but don't extrude too much to avoid waste.

2.Apply evenly: Use a scraper or brush to evenly apply the glass glue to the surface that needs to be bonded. Make sure to apply the Zen Tremor evenly and avoid bubbles or voids.

Glass glue is a multi-functional glue, usually used for glass, ceramic, metal, wood and other materials to bond in the air. Proper use of glass glue ensures the bonding effect and prolongs its service life.

5.Drying time: After the bonding is completed, it is necessary to wait for the glass glue to dry. In general, the drying time of glass glue is 24 hours, but the drying time may be shorter in the environment of the ring cavity with higher temperatures.

4.Fixing material: After the bonding is complete, the adhesive material can be fixed to the surface using clips or other fixing materials to ensure a strong bond.

3.Adhesive material: The material to be bonded is placed on a surface coated with glass glue. Make sure that the adhesive material is in close contact with the surface to avoid voids.

3.Adhesive material: The material to be bonded is placed on a surface coated with glass glue. Make sure that the adhesive material is tightly bonded to the surface to avoid voids.

The use of glass glue is as follows:1. Do a good job of cleaning: Before gluing the glass glue, it is necessary to remove dirt, dust and other dirt from the surface of the joint.

Clean the surfaces of the two objects that need to be glued and keep them dry. The interface surface is then covered with plastic tape to ensure a perfect seal and neat lines.

2. Specific bonding: cut the nozzle, install the needle-nose tube, and then cut at a 45-degree angle according to the size of the joint. Finally, a caulking gun is installed, squeezing the rubber at a 45-degree angle along the gap to ensure that the rubber and the substrate surface are in close contact.

When the seam width is greater than 15 mm, the glue must be applied repeatedly. After gluing, trim the surface with a knife to remove excess glue, and then remove the tape. If any stains can be removed with a damp cloth.

3. Glass glue pasting time and curing timeThe curing process of glass glue develops from the surface inward. Silica gel with different properties has different surface drying and curing times. Therefore, if the surface is to be repaired, it must be done before the glass glue dries.

In the first step, the glass glue is preheated for 15 minutes (only for some Henkel products);

In the second step, the new glass is thoroughly cleaned with Henkel FL cleaner;

In the third step, apply primer to clean glass for 8517h and dry for 10 minutes;

The fourth step is to remove the window trim;

The fifth step is to cut the glass glue of the original car and remove the old glass;

The sixth step is to flatten the residual glue on the frame, if these residual glue is the original glue, it will become a good bottom layer of Henkel glass glue, because Henkel after-sales glass glue and the original glue have good compatibility, and the bottom layer does not need to be coated with primer to achieve a good bonding effect;

Seventh, if the metal or paint is exposed on the frame, these parts need to be primed for 8517h;

In the eighth step, cut the nozzle as high as required;

The ninth step is to apply sizing with a triangular cross-section;

Step 10: Install the glass in the correct position before the Henkel glass glue surface dries.

The eleventh step is to install the window trim and conduct a water leakage test;

The twelfth step, according to different rubber grades, wait for the corresponding safe driving time, and then drive normally.

1. Treatment surface: Before the construction of glass glue, the base layer should be cleaned, especially the water, dust, grease and other pollutants on the surface of the gap, and some solvents can be used appropriately, such as butanone, xylene, etc. to clean the surface, and then use a dry rag to wipe the surface clean, to remove all the residues, but at the same time to ensure that the base is dry and clean, so as to facilitate construction.

2. Plastic tape: During construction, the surface near the interface should be covered with plastic tape, which has a good sealing effect, and can also ensure the perfection of glass glue in the construction process and will not affect the surface.

3. Playing glass glue: The newly opened glass glue needs to cut the nozzle of the hose first, then install a needle-nosed tube, and then cut it at an angle of 45° according to the size of the caulking. When playing glass glue, it is necessary to pay attention to the sub-gun barrel filled with glass glue at an inclination angle of 45 ° and beat the glass glue along the gap, so as to ensure that the surface of the glass glue and the substrate are fully and closely contacted.

In the process of playing glass glue, it is necessary to pay attention to the uniform force and speed, so that the glass glue can be evenly proportioned and good-looking. When the width of the seam is greater than 15 mm, it is necessary to repeat the glass glue many times. After the construction of the glass glue is completed, you can use a knife to smooth the surface of the glass glue, and then remove the excess rubber.

The above is an introduction to the use of glass glue, I hope it will help you.