Do you need a pressurized pump for wall hung boiler floor heating, and do you need to install a circ

If the system is large--- area is large; The original circulating water pump of the wall-hung furnace has a small circulation capacity, and the room is not hot, so increasing the pump can have a little effect.

However, it is better to add a mixed water tank and then a pump, which can effectively solve such problems.

The gas wall-hung boiler used in the household is generally not equipped with a circulating pump, and the gas boiler used in the project, due to the relatively large heating area, in order to make the water of the pipeline circulate faster, it is best to have a circulating pump --- Longzhou floor heating.

With a condensing boiler, there is no need to install a water mixing device. Condensing boilers have special anti-corrosion treatment, especially South Korea's condensing boilers, which are specially designed for floor heating systems, and those boilers that want to be filled with mixed water must be European boilers, because European boilers only consider radiator systems, so if you want to install floor heating, you still have to choose Korean boilers to pass the test.

The gas wall-hung boiler of the wall-hung boiler is more diversified, and in terms of brand, you can go to the wall-hung boiler network under the warm nest and the Chinese floor heating network of the warm nest for a specific understanding.

The official ** of Warm Nest China Floor Heating Network is [8dn].

Warm nest wall-hung boiler official network [8GL].

Depending on how big your area is, large areas can be used.

See how big an area you are. How to configure the system.

Do you need to install a circulating pump for wall-hung boiler with floor heating, the water in the wall-hung boiler system is pumped by a closed water pump for circulating heating. A circulating water pump needs to be installed. The reason is that the wall-hung boiler and the floor heating are an integral circulation system, the wall-hung boiler heats the water, and the hot water is pumped into the floor heating by the circulating pump, and then the water from the floor heating is pressed back to the wall-hung boiler for heating.

It is not enough to simply pass the automatic circulation type of the hot water. The water is now heated inside the hanging fireplace and then goes into the manifold. In the into the underfloor heating coil.

The installation of circulating water pump is conducive to the circulation of water, and also greatly saves the cost of use. Sometimes the hot water of the wall-hung boiler cannot be circulated in time, resulting in the automatic stop of the wall-hung boiler. Because the water has already boiled to a certain temperature.

However, at this time, the hot water did not enter the floor heating coil smoothly. So the underfloor heating effect is very poor. Generally, when installing floor heating, we install circulating pumps.

The water in the wall-hung boiler system is pumped and heated by a closed water pump. The hot water flows out of the heating hot water pipeline, and then circulates and pumps the water through the water pump, and in terms of system pressure balance, it flows back to the inside of the wall-hung boiler from the heating return pipeline, is absorbed into the heat exchanger by the water pump, is heated by the flame in the combustion chamber, and circulates out of the hot water pipe again, flows through the radiator or floor heating, and then returns to the wall-hung boiler. For the closed hot water heating system with a variety of heat users, the circulating water pump should first draw the comprehensive heating adjustment curve, and superimpose the total water flow curves of the network with various heat loads to obtain the maximum design flow value of the network at a certain outdoor temperature as the basis for selection.

The maximum design flow of the network is the maximum design flow rate of the network for the parallel closed hot water heating system with multiple heat users that is common only for a single heating load or adopts centralized quality regulation. Hope it helps.

AbstractThe installation of booster pump for floor heating can make the water flow of floor heating more rapid, the circulation effect is better, and the indoor temperature can be effectively raised. However, I personally feel that the installation of underfloor heating booster pumps will affect the circulation of hot water in other homes, and will have an impact on the temperature of other homes. Moreover, the floor heating booster pump needs to use power supply, and the floor heating booster pump will have a certain sound when it is working.

If the temperature in the room is not very good. Floor heating can be cleaned, which can also effectively increase the temperature in the room. Personally, I don't think it's necessary to install a floor heating booster pump at all.

Is it useful to install a booster pump for natural gas wall-hung boiler floor heating?

The installation of booster pumps for underfloor heating can make the water flow of underfloor heating more rapid, circulate better, and effectively increase the indoor temperature. However, I personally feel that the installation of underfloor heating booster pumps will affect the circulation of hot water in other homes, and will have an impact on the temperature of other homes. Moreover, the floor heating booster pump needs to use power supply, and the floor heating booster pump will have a certain sound when it is working.

If the temperature in the room is not very good. Floor heating can be cleaned, which can also effectively increase the temperature in the room. Personally, I don't think it's necessary to install a floor heating booster pump at all.

I believe that most people have a certain understanding of the wall-hung boiler, which concentrates the water heater and heating function, and only needs to install the wall-hung boiler at home, so there is no need to install a water heater. The wall-hung boiler can continue to provide hot water without interruption, which provides a lot of convenience for the family's daily hot water drinking and winter heating. However, the wall-hung boiler is connected to tap water, and the water pressure needs to be taken into account, so does the wall-hung boiler need a booster pump?

Let's take a brief look with Qeeka Home experts.

1. Do you need a booster pump for a wall-hung boiler?

No, because the wall-hung boiler itself has its own booster pump, so there is no need to install it separately. Generally, as long as the tap water pressure is reached, the wall-hung boiler can be used normally, and basically the water pressure in most cities meets this pressure range.

Second, how to choose a household wall-hung boiler.

1. Look at the function.

From the functional point of view, household wall-hung boilers are divided into single heating, dual-purpose furnaces and other categories, that is, single heating function and heating + domestic hot water two different functions of wall-hung boilers, generally speaking, the installation of dual-purpose furnaces is more economical, cost-effective, can save various expenditures on water heaters.

2. Look at the power.

When choosing a household wall-hung boiler, pay special attention to its power, which is related to whether it meets the needs of use. Generally, the power is selected according to the area of the home, for example, a 100-square-meter house should choose a wall-hung boiler with 18 kilowatts of power, and a 100-140 square meter house should choose a 24-kilowatt wall-hung boiler.

3. Look at the promotion.

Wall-hung boiler and water heater are the same, there is a difference in the upgrade, that is, the difference in its capacity, the rise of the wall-hung boiler is related to the heating capacity, generally the greater the rise, the stronger the heating capacity, if the upgrade is not selected, there may be problems such as insufficient or waste.

Summary: The above is about the introduction of the wall-hung boiler needs a booster pump, and how to choose a household wall-hung boiler, I hope that the content shared can have some reference for you, if you want to know more relevant information, you can **** Qeeka Home information.

1. The wall-hung boiler does not need a booster pump.

2. Because the wall grip hanging furnace itself has its own booster pump, there is no need to install the leather stove separately.

3. Generally, as long as the tap water pressure is reached, the wall-hung boiler can be used normally, and basically the water pressure in most cities meets this pressure.

Wall-hung boilers and water heaters are the same, there is a difference in lifting, that is, the difference in its capacity, the rise of the wall-hung boiler is related to the heating capacity, generally the larger the rise, the stronger the heating capacity.

It is a 32kw wall-hung boiler.

With 80 square meters of floor heating, do you want to add a mixing tank and a circulating pump?

The general practice is to be able to bring it up without adding. If you add it, it is a secondary system, which is conducive to energy saving and better protection for the furnace.

Regardless of whether you add it or not, pay attention to the linkage control of the floor heating thermostat and the wall-hung boiler. If it is added, the external water pump should also be controlled by linkage. With linkage control, the local heater thermostat can be turned off, or the wall-hung boiler can be stopped working synchronously after reaching the set temperature, which can effectively save the use fee.

Otherwise, if there is no linkage, the wall-hung boiler will not stop synchronously, but start and stop according to the water temperature set by the furnace itself, which will cause waste of gas and the water pump is easy to suffocate.

To do linkage is to add a linkage, which will not increase a lot of costs, as long as a few hundred yuan. The linkage is also called the controller, or the centralized controller. There are various styles, as shown below:

**Controller.

Linkages. <>

System energy-saving linkage.

Secondly, we must add a system protector, which can effectively prevent scaling and microbial breeding in the water, and has a certain lubricating effect to prevent the pump from stuck, protect the whole system, and prolong the life.

Floor heating system with a protective agent.

Hope it works for you, hope.

Do the math how much it will cost you to renovate your home.

In order to improve the indoor heating effect, in order to have convenient domestic hot water, some families will install wall-hung boiler and floor heating at home at the same time, if the wall-hung boiler and floor heating are to operate normally, then enough water pressure is needed, so how normal is the water pressure of wall-hung boiler and floor heating? Let's take a look.

How much is the water pressure of the wall-hung boiler and the floor heating normal.

1. Under normal circumstances, the water pressure of wall-hung boiler and floor heating should be between 1bar and normal. The water pressure of the wall-hung boiler should not be too high or too low. As long as the water pressure of the wall-hung boiler and the floor heating is between the arrival, the wall-hung boiler will generally not be affected and can still be used.

2. If the water pressure is lower, then the wall-hung boiler will not be able to operate normally, and then it is necessary to carry out the water replenishment operation in time to fill the wall-hung boiler with water, otherwise it is easy to cause the wall-hung boiler to appear cold and hot, or it cannot be started directly.

3. If the water pressure is higher, the safety valve of the wall-hung boiler will automatically relieve the pressure, which will bring unnecessary economic losses to the owner. For safety reasons, when the wall-hung boiler has automatic pressure relief, we should check in detail whether there is a fault inside the wall-hung boiler, or check whether the wall-hung boiler is not operating normally.

4. We can check whether the wall damage knows whether the hanging boiler can operate normally and whether there is a fault through the water replenishment operation. If you find that there is a problem, then you need to contact a professional maintenance person in time to help deal with it. In order to ensure that the wall-hung boiler can operate normally, it is recommended that you must carefully check whether the water pressure values of the wall-hung boiler and floor heating are within the specified normal range.

5. If the water pressure value of the wall-hung boiler and floor heating is within the specified normal range, then it can be used normally. If the water pressure value of wall-hung boiler and floor heating is not within the specified normal range, then it is necessary to take appropriate methods to deal with it according to the actual situation, so as to avoid problems and potential safety hazards.

The above is all the content introduction about how much normal water pressure is for wall-hung boilers and floor heating, I hope it can help you. In the daily use process, it is necessary to ensure that the water pressure value of the wall-hung boiler and floor heating is within the specified normal range to avoid problems and potential safety hazards.

Enter the area and get the decoration for free**].

The water pressure of the wall-hung furnace and the underfloor heating should normally be between the bars, and generally speaking, it is most suitable around the bars. If the water pressure is too low, it may cause the wall-hung boiler and floor heating to not work normally or unstable; If the water pressure is too high, it will increase the load on the equipment and may even cause safety accidents. Therefore, it is recommended to check the water pressure regularly, and if necessary, timely replenishment or exhaust operations to ensure the normal operation of the wall-hung boiler and the floor heating system.

For specific operation methods, please refer to the product manual or consult a professional.

How much is the normal water pressure of wall-hung boiler and floor heating? Generally speaking, his pressure can not be too high, nor too low Mu Laokuan, that is to say, his pressure is the highest in the left and right, if the pressure is too high, there is no benefit to the wall-hung boiler, so generally speaking, one kilogram to one and a half kilograms, this is the best.

Summary. Hello, we are happy to answer for you, your question is: How to install the booster pump of the wall-hung boiler The answer is:

There is an interface between the circulating booster pump and the wall-hung boiler, and the user can directly connect the two through the pipeline. The wall-hung boiler uses natural gas, artificial gas or liquefied gas as fuel, the fuel is output through the burner, and after burning in the combustion chamber, the heat is absorbed by the heat exchanger, and the circulating water in the heating system is heated through the heat exchanger through the reciprocating heat, so as to continuously output heat to the building and provide a heat source for the building.

Hello, I'm glad to answer for you, your question is: How to slow down the installation of the potato mold in the hand cavity of the wall-hung boiler booster pump The answer is: the circulating booster pump and the wall-hung boiler have interfaces, and the user can directly connect the two through the pipeline.

The wall-hung boiler uses natural gas, artificial gas or liquefied gas as fuel, the fuel is output through the burner, and after burning in the combustion chamber, the heat is absorbed by the heat exchanger, and the circulating water in the heating system is heated through the heat exchanger through the reciprocating heat, so as to continuously output heat to the building and provide a heat source for the building.

In addition to the heating function, the general dual-purpose gas wall-hung boiler also has the function of hot water (that is, in addition to heating, it also has the function of a gas water heater). The wall-hung boiler can provide a heat source for both the heat sink and the floor heating system. The commonly used wall-hung boilers are divided into two types: heating domestic hot water filial piety dual-purpose furnace and single floor heating stove.

Tanda. The circulating pump has a low travel and is only used to overcome the pressure drop in the circulating system. Low-head pumps are available. The circulating pump refers to the function of the missing pump, and the centrifugal pump refers to the structure of the pump, and the two are completely two concepts.

The working principle of the grinding block circulating pump is to circulate the water, and the pump used is called the circulating pump, which has low requirements for water quality, and if the circulating water contains small debris, it will not affect the work of the circulating pump. For example, the hot water in the plumbing and heating pipes is circulated blindly by circulating pumps.

How to install the Searchable Bangbang? Does he have her underneath the ordinary half box without arrows? Which set of tricks is suspicious? How to press it has an arrow symbol? How is it installed? What I mean by this is that he has an arrowhead and an arrow, and I can't figure out which direction the arrow is facing.

1.Patrol point installation, is to fix the patrol point in the patrol position, there are the following methods, according to your actual situation to choose (AB glue, nails, punching drills and drill holes and then fixed. If the tubular can drill the hole first, the eye is slightly longer than the patrol point, and the long distance will affect the card reading.

2.Software installation, the general manufacturer software Jianheng has an instruction manual, you can operate according to that, the main setting items have a few points (location button setting, stick number setting, line setting, plan setting), if there is a personnel card and event book, you need to set these two also set up Thank you for your patience.

Doesn't the circulating pump have arrows? In that direction.

Right. Face asked the wall-hung stove head to the right?

Yes. Is it true that he has the original equipment to the left? It is installed to the left.

That's right. I also didn't respond after working on the left installation.

The arrow is left.