How to turn on the floor heating of the wall hung stove? How to turn on the heating of the wall hung

1. Connect the power supply to the wall-hung boiler.

2. Turn on the wall-hung boiler, some wall-hung boilers will have a switch.

3. Open the gas valve.

4. Open the water supply and return pipe valve of the floor heating.

5. Find the installation position of the water separator, and then connect the power supply.

6. Turn on the indoor floor heating thermostat, pay attention to the set temperature, if the indoor temperature is 21°, then you can set it to be greater than 21°C.

7. Return to the wall-hung boiler, look at the pressure, if the pressure is up and down, then there is no problem, if it is lower, open the water replenishment valve of the wall-hung boiler, and then slowly open the water replenishment valve on the wall-hung boiler, while looking at the pressure value, while replenishing water.

9. You have to know what the symbol on the wall-hung boiler represents.

10. If you can't open it, you can contact me, if it doesn't work, I can tell you that I**, I** will teach you.

Open the valve of the floor heating and turn on the heating of the wall-hung boiler, and the specific operation depends on what kind of boiler you have.

Summary. 1. Open the water inlet valve under the wall-hung furnace and fill the wall-hung furnace and floor heating pipes or radiators with water. The water filling switch is generally located under the hanging furnace.

2. When the water pressure gauge on the wall-hung boiler rises to between 2-3, you can close the water inlet valve, and the water pressure should not be too high, otherwise it will crush the water pipes and other accessories in the wall-hung boiler and cause water leakage. 3. After the pressure reaches the requirement, you can plug in the power supply, turn on the gas switch, and press the switch on the wall-hung boiler to start the operation of the hanging boiler. The wall-hung boiler with a panel display can be seen that the temperature of the warm air is rising.

During the operation, the temperature can be adjusted to reach the ideal room temperature, but the warm temperature can not be too high at the beginning, you can adjust it to 45 degrees first, burn it for a period of time and then adjust it according to the body feeling.

Hello, dear, the operation method of turning on the heating of the wall-hung boiler is as follows:

1. Open the water inlet valve under the wall-hung furnace and fill the wall-hung furnace and floor heating pipes or radiators with water. The water filling switch is generally located under the hanging furnace. 2. When the water pressure gauge on the wall-hung boiler rises to between 2-3, you can close the water valve and the water pressure should not be too high, otherwise it will crush the water pipes and other accessories in the wall-hung boiler and cause water leakage.

3. After the pressure reaches the requirements, you can plug in the power supply, turn on the gas switch, and press the switch on the wall-hung boiler to start the operation of the hanging boiler. There is a panel display of the wall-hung boiler, you can see that the temperature of the warm is rising, and the bridge accompanies it. During the operation, the temperature can be adjusted to reach the ideal room temperature, but the warm temperature can not be too high at the beginning, you can adjust it to 45 degrees first, burn it for a period of time and then adjust it according to the body feeling.

Kiss! Hello, very open Tongran happy for the wheel which you answered <>

How to open the floor heating of the pro-wall-hung boiler is as follows: first connect the power supply of the wall-hung boiler and turn it on, then hit the water supply and return pipe valve of the floor heating and the valve of the gas opening, and then find the installation position of the water separator and connect the power supply, and then open the thermostat of the floor heating and set the temperature above 21 degrees. Finally, pay attention to the pressure of the wall-hung boiler, if the pressure is on the left and right.

2. What are the brands of wall-hung boilers 1. Vaillant (Vaillant (China) heating and refrigeration environmental technology ****) brand Birthplace: German brand founding time: 1874 2. Bosch Bosch Thermal Power (Bosch (China) Investment ****) brand Birthplace:

In 1917 4, the little squirrel Squirrel (Guangzhou Decision Home Environment Technology ****) brand birthplace: Guangzhou City, Guangdong Province brand founding time: 2000 5, baxi Baxi (Xiderui Thermal Energy Technology (Tianjin) ****) brand birthplace:

British brand founding time: 1866 June, Ariston (Ariston thermal products (China) ****) brand birthplace: Italian brand founding time:

1960 7, Beretta Beretta (Riello Thermal Equipment (Shanghai) ****) brand Birthplace: Italian brand founded time: 1969 8, Wanhe Vanward (Guangdong Wanhe New Electric Co., Ltd. ****) brand birthplace:

Do you have any other questions?

Summary. Step 1: When we turn on the indoor temperature control panel, we can set the panel temperature to the required comfortable temperature, generally 18-22 will be more comfortable.

If the set temperature is higher than the actual temperature in the room, then the panel will display a heating symbol, which means that the panel is working properly. Step 2: Check whether the switch of the heating supply and return pipe under the boiler is turned on, and also check whether the pressure of the boiler is between 1-2 kg, if the pressure value is less than 1 kg, you need to contact a professional for pressure (water replenishment).

Step 3: When turning on the heating function of the wall-hung boiler, you can set the temperature to 60 degrees, observe the boiler for 3-5 minutes, the flame indicator light is on, and the boiler temperature is slowly rising, which means that the heating has been turned on and running.

Step 1: When we turn on the indoor temperature control panel, we can set the panel temperature to the required comfortable temperature, generally 18-22 will be more comfortable. If the set temperature is higher than the actual temperature in the room, then the panel will display a heating symbol, which means that the panel is working properly.

Step 2: Check whether the lead switch of the heating supply and return pipe under the boiler is turned on, and also check whether the pressure of the boiler is between 1-2 kg. Step 3:

When the heating function of the wall-hung boiler is turned on, the temperature can be set to 60 degrees, and the boiler can be observed for 3-5 minutes, and the flame indicator light will be lit and the boiler temperature will rise slowly, which means that the heating has been turned on and running.

The wall-hung boiler was turned on for heating and the water was out, the air pressure gauge repeatedly jumped horizontally, and the heating return water leaked out. The display keeps flashing and the machine keeps ringing. What is the reason.

It may be that the pressure gauge of the wall-hung boiler is faulty and ignites or the expansion tank is broken, it is recommended to carefully check the expansion tank of the wall-hung boiler and the water pressure gauge of the wall-hung boiler, and carry out the maintenance of the wall-hung boiler and deal with the mu of the finch quietly and resistantly.

When the heating water was turned on, there was a noise in the case, and then there was a water leak, it was brown hot water, and there was also gas discharge.

This is specific to the maintenance master to see.

In this case, it needs to be repaired. Need.

Here's how to turn on the heating of a wall-hung boiler:

First, open the supply valve and exhaust valve of the warm wall-hung boiler, and close the exhaust valve when there is water flowing out. When the water pressure of the replenishment valve rises to the left and right, it can be closed after the water pressure has stabilized. Then turn on the power of the warm wall-hung boiler and press the start button.

Set the heating mode and heating water temperature of the wall-hung boiler, set the temperature of the heating hot water on the upper and lower buttons on the left side of the wall-hung boiler, and set the water temperature of domestic water on the right side. The normal water temperature is about 55 degrees, the radiator temperature is above 60 degrees, and the bath temperature is adjusted to about 41 degrees. The specific temperature is subject to your own comfort level.

Precautions. Note that before starting the machine, check whether the gas type is consistent with the label of the wall-hung boiler; whether the heating pipes are well connected; and whether the gas and valves are open. Water injection pressure test: Turn the water supply valve of the wall-hung boiler counterclockwise.

At this time, the cold water enters the wall-hung boiler and flows along the heating pipes. Pay attention to radiators and pipes for water leaks. Then open the radiator exhaust valve in turn and expel the air inside the radiator until the water flows out of the radiator exhaust valve and closes.

How to turn on the heating of the wall-hung boiler:

1. Check the power supply to ensure the power-on state, and require a 220-volt stabilized power supply, with good grounding and no static electricity.

2. Check the gas source, confirm that the gas has been purchased, and insert the gas meter with the gas card to read and write. Confirm that the gas meter battery is in normal use (it is best to ask for Nanfu batteries, it is not recommended to use low-power batteries, which will cause ignition failure).

3. Check the waterway to ensure that the pipeline does not leak, the heating valves are all open, the heating valves under the wall-hung furnace are all open, and the water pressure is replenished. The rural tap water pressure is insufficient, and it is necessary to use a booster pump to pressurize it. Do not exceed the water replenishment to prevent the leakage of the wall-hung furnace drain valve.

After the water replenishment, close the water replenishment valve of the wall-hung boiler (generally the black or blue plastic knob under the wall-hung boiler is tightened in a clockwise direction).

4. Check whether the smoke pipe of the wall-hung furnace itself is plugged tightly, and the smoke pipe installation must be flat and the angle is slightly inclined downward to prevent rainwater from flowing back, and it is strictly forbidden for the wall-hung grate smoke pipe to go up vertically.

5. After all the inspections are completed, adjust the switch of the wall-hung boiler to the winter heating gear (generally the wall-hung boiler is a snowflake sign), and adjust the water temperature to 55 degrees. At this time, the display screen of the wall-hung boiler will show the ignition working status. Wait for 3-5 minutes, at this time, the water supply pipeline of the wall-hung boiler will be heated and the ignition will be normal.

Test the heat of the radiator one by one in the direction of the water flow until the temperature of the return line increases.

6. After all the radiators are heated, observe whether the water pressure gauge has dropped, close the wall-hung boiler if it falls, continue to replenish water until, and repeat the start-up action at this time.

Summary. Hello, the method of turning on the heating of the wall-hung boiler is as follows: screw the heating valve all the way to the head according to the counterclockwise direction, that is, open the valve to the maximum flow. If you screw it all the way to the head in a clockwise direction, it is equivalent to turning off the inlet and outlet water of the radiator.

Hello, the method of heating the wall-hung boiler is as follows: screw the heating valve to the head according to the counterclockwise direction, that is, open the valve to the most cracked type of early flow. If you screw it all the way to the head in a clockwise direction, it is equivalent to turning off the inlet and outlet water of the heating finches.

The valve of the separator is then operated using the same operating method. However, there are also water separator valves that are installed on the branch of the water separator, and if it will be parallel to the direction of the floor heating pipe, the valve will be opened. If it crosses the direction of the underfloor heating pipe at an angle of 90 degrees, then the valve is closed.

Next, you should check whether the pressure of the wall-hung boiler is between 1 bar and 2 bar. Under normal circumstances, the pressure of the wall-hung boiler should be set at 1 bar before it can be opened normally, but some wall-hung boiler brands are set at 1bar. Therefore, the pressure of the wall-hung boiler should be between 1 bar and 2 bar is the most suitable, but it must not be exceeded.

If the pressure of the wall-hung boiler is too low, then you need to open the make-up valve at the bottom of the wall-hung boiler, and then open it in a counterclockwise direction, and the make-up valve will start to replenish the water. If it is opened in a clockwise direction, the make-up valve will be closed. Some owners will install heating, gas, tap water valves and so on at the bottom of the wall-hung boiler, and usually rarely use the hot water mode of the wall-hung boiler, so before using the wall-hung boiler, you must remember to open the radiator valve.

In addition, you must remember to check each connection to avoid water leakage and potential safety hazards.