Henderson Computer Network Connect 711, Henderson Computer Network Connection

If the broadband Internet shows the fault of "error 711", it is caused by the computer using the win7 system and updating the system patch KB917606. You can do this in the following ways:

1. Remove this patch (uninstall it through 360 or system programs);

2. Open the command line cmd (run as an administrator) at the beginning of the computer, enter netsh winsock reset enter, and restart the computer, the specific function and path are subject to the actual page;

3. After the first and second methods are not working, it is recommended that you reinstall the system and do not update the patch KB917606.

Hehe, how is your luck so good?? The last time I knew about it in half a year, I ran into this problem with you. First of all, to correct your mistake, the engine fault light you said is actually an exhaust emission control light in the Volkswagen Audi series, and the EPC light is the engine fault light.

These two lights, although they are in the instrument guess god, are essentially controlled by the engine computer. When the key is turned on, the engine computer gets power and starts working, lighting up the two lights. If you say that the key does not light up, it means that the engine computer has not entered the working state.

At the same time, the failure of the engine to start is also evidenced by this. The problem may be a failure of the engine computer power supply, grounding, and the engine computer itself. I don't know if the other equipment in the car is not working properly when the lights are not on?

For example, are the other lights on the meter on? If not, it's most likely an engine computer malfunction. If there is, then it may be the power supply, grounding.

and the failure of the vehicle digging gear on-board network. (Your problem is most likely due to the failure of the engine computer itself). Thank you!

The driver said that he was walking and turned off the ignition, and he couldn't hit it until the EPC light of my factory was still on, and after testing, it was found that the oxygen sensor was cracked, and it was played after treatment, but it was still walking and couldn't be played, and the EPC light was not on. I left it all night, why is that?

It's just a boot start item.,Why do you do such a profound thing?,If it's a laptop,Generally when booting out of the current motherboard manufacturerlogo,Press F2,Select the left and right arrow keys to boot,Don't worry about the first line,Move to the second line and point enter,In the next screen,Move all the items above to the bottom,Find the optical drive from below,Generally with the word "cd dud"That is,Click on X to move it to the top,Click F10 to enter,Save the settings to exit。 Some motherboards are not F2, they may be F1, this manual says; Also,If you're a desktop computer,BIOS The method of setting boot startup items is more troublesome than this,The same is to press a certain key when the motherboard logo appears,But it's not F2 or F1,It's the del key (usually this),Select Advanced on the next screen

BIOS Features (Advanced BIOS Settings) press enter, and select "Boot" next

device select...Enter,Just change the "1st" to the dismantling of which hall brother should be changed to a CD-ROM drive.

It's good to press "+" to set it and exit. After installing the system, remember to change the setting to the hard disk as the first boot item, otherwise it will waste boot time when you boot your own optical drive. Done, add me if you don't know something, it's over this time, hehe, remember to choose me the best

The drivers are all open and can be updated through the Driver Genie to drive life.

Click on the taskbar, click on Show Desktop, and you're really good to go.

Remember to adopt it.

It is recommended not to change it, the notebook is not like the desktop graphics card and the motherboard can be disassembled and repaired, the notebook graphics card is broken, which means that this book has been half expensive But you can afford to repair it, the notebook is an integrated graphics card and the power motherboard are soldered together not just to change the graphics card can be used, a few hundred graphics cards are not expensive Generally, the cost of welding the graphics card and the electric board together is too expensive, because a welding equipment is about 10 to 200,000 yuan, and the general company can not afford such a large investment, If it's broken, it's broken, and it's better to buy another one for maintenance, but it is recommended to use the desktop as much as possible where you don't need a notebook, the cost is low, convenient and simple, and the maintenance and care yourself can generally do, the notebook is too complex and expensive, and the maintenance can't afford it, and the equipment at the welding point is too expensive. Because the small repair shop there definitely does not have that kind of welding equipment, you have to pay to go to a large network maintenance company or institution with equipment to repair it. Compared to the desktop type, the notebook is really expensive to repair.

If you change a graphics card, you need thousands of dollars in total, and if you use a warranty card, it will be much cheaper to return to the factory for warranty.