The Civic stepped on the brakes and the small light was on, and everything was normal without steppi

Is the light of the meter on, you check if there is a brake light burned out.

Hello. Check whether the brake light related circuit is caused by a short circuit with the small light line, I hope it can help you. It is also possible that the brake bulb is burned out. [Car questions, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hello According to the problem you reflected, the control circuit of your rear brake bulb is short-circuited with the small light circuit, it is recommended that you check it to avoid other problems [car problems, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, it is possible that your rear light circuit is short-circuited, it is recommended that you go to check the car problem, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

It is recommended to check whether the rear brake bulb is caused by a short circuit or a bad wiring [car problems, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

What kind of little light is on? The brake lights are normal.

Step on the brakes and the brake lights will definitely be on, look.

Hello, what light is on, is the brake light on. Normal.

Hello. Normal, happy with the car! If my reply can help you, please help choose it, thank you very much!

Hello! It's a car line contact problem, and you can look for it along the line! Hope it helps!

Summary. Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, for you to find the corresponding problem solutions and solutions!

Hello, the normal situation is to press the brake, and then you can start the vehicle, without the car, the brake is particularly hard, you need to press hard, if it still doesn't work, it means that there is a problem with the brake switch, and it may be that you are not hung to the P gear, resulting in failure to start.

The new Civic car can't brake down and can't start the car.

Hello, I have seen your inquiry, please wait for a moment and answer it for you immediately.

Hello, I am your exclusive technician, attentive, careful, dedicated to answering your car questions, for you to find the corresponding problem solutions and solutions! Hello, the normal situation is to press the brake, and then you can start the vehicle, without the car, the brake is particularly hard, you need to press hard, if it still doesn't work, it means that there is a problem with the brake switch, and it may be that you are not hung to the P gear, resulting in the inability to start the solution Check whether the brake switch contact is damaged, replace the brake switch,

It may be caused by the leakage of the system dynamic fluid, at this time, it is necessary to go to the 4S shop to check and repair the leakage, and then replenish the missing brake fluid, and the handbrake will return to normal extinguishment.

In addition, the thinning of the brake pads will also lead to this phenomenon, because the brake pads will cause the brake fluid level to drop after they become thinner, and the handbrake light will be lit, but the fuel volume will drop to the point where it seems to be turned on and not turned on, and the handbrake light will be on and off with the shaking version of the vehicle.

The electronic parking brake can be given accurate parking force by the controller through the slope sensor, and when starting, the parking control unit will automatically release the parking brake when the driving force is greater than the driving resistance through the information provided by the clutch distance sensor, the clutch pinching speed sensor, the accelerator pedal sensor, etc., so that the car can start smoothly.

Even if you are congested and parked in the city, as long as you enable the auto hold function, the corresponding automatic parking function will be activated. When it is necessary to release the stationary state, you can also release the brake with just a light touch of the accelerator, which is really practical for those car owners who often stop and go in the city, and also reduces some unnecessary accidents caused by everyone's carelessness.

It is recommended to park the car directly, do not use it again, and must be put this troubleshooting later. Then use it normally.

In this case, it is basically because of the fault of the brake line, it is recommended to find an experienced master to eliminate it.

That's because the car has the function of automatic parking turned on. When this function is turned on, the handbrake will be automatically unlocked when the car is driving, and when the car is stopped, the handbrake will be automatically turned on, and this will not happen when the automatic function is turned off.

The handbrake light will be on for a while, and it will disappear when you step on the brake while driving, indicating that your handbrake is not put in place, which will cause it to be on for a while and not on for a while, pull your handbrake in place, and then put it down again, and it will not be on again.

The situation you are talking about is that the wiring of the car is aging and faulty. You need to go to the repair department of the car to check the line. It is possible that the power connector is loose. But you must go to the maintenance in time, and you can't drive with illness.

In this case, most of the brake pads are worn thin, beyond a certain specified value, it may be that the brake fluid is lower than the lower limit of the oil cup, this situation will also occur, you can check it to know what the reason is.

Hello, according to the situation you described, it is caused by not putting the handbrake in the end, it is recommended to lift the handbrake again and then put it down.

Hello friend, like you said, the situation should be that there is a little problem with your brake lights, so you should go to the repair shop to fix it quickly, so that it can be better. It is more convenient for you to pass normally.

If this happens after the handbrake is completely lowered, then the copper electrode inside the handbrake light switch is electrocuted and burned short.

It may be caused by a lack of brake fluid, or there may be a leak in the brake fluid. You can go to the repair shop and have it checked. There is also to check whether the vehicle's handbrake is put down to the end.

In this case, it is possible that your handbrake cable is not so completely returned, check it, is the handbrake cable stuck? Is the parking brake switch damaged?

It may be caused by a little poor contact, you can send it for maintenance to take a look, rest assured.

Usually because. If the system is caused by the leakage of freeze, it is necessary to go to the 4S shop to check and repair the leakage, and then replenish the missing brake fluid, and the handbrake will return to normal extinguishment.

Such a situation generally occurs at night, because the car tail light is used to show the width of the night, so it must be long-on, as for the problem that the brake is not lit, if it is said that after stepping on the brake, the brake light does not turn on, and still maintains the original brightness;

If the brake light goes out after stepping on the brake, then it means that there is a problem with the circuit board, and the circuit problem is not clear, and only the check can produce the result.

Pay attention to the replacement of brake bulbs: the tail lights of vehicles produced in China are generally"One brew for two purposes"There are two filaments in the bulb, the weaker one is the small light, and the stronger one is the brake light. Some manufacturers design it as a high and low foot plug-in type, which is very convenient to use.

Be careful not to reverse the connection when replacing.

Answer; bai

The brake light is on all the time

Even if you don't step on the brakes, then let's take a look at what is going on and how to solve it.

If the brake light is always on, then it can be judged that there are several fault situations, namely the lack of brake fluid, the damage of the brake switch, the failure of the tail light circuit, the wear and aging of the brake pads, etc., and then we will pick a few common reasons to analyze.

1. Lack of brake fluid.

Brake fluid plays a vital role in the braking system of the car, when the driver steps on the brake pedal, the force of stepping down from the pedal, by the piston of the brake master cylinder, through the brake fluid to the brake cylinder located in the wheel, so that the brake pad and the wheel contact, to achieve the purpose of stopping the vehicle from advancing. The lack of brake fluid will also be accompanied by a significant lack of braking force, and even a loss of braking force will occur in severe cases. In this case, it is sufficient to replenish the brake fluid in time.

2. The brake switch is damaged.

In this case, the brake pedal and the brake sensor switch are not in good contact or the sensor switch is broken, and it needs to be disassembled for inspection.

3. Brake pads are worn and aged.

Brake pad wear and aging may also cause the brake light to be on all the time, this time to check the thickness of the brake pad, if the thickness of the brake pad is lower than the specified value, generally, then it is likely to break during driving and cause danger.

In addition to the fault factor, it is also possible that the owner forgot to put down the handbrake and the brake indicator stayed on. In short, the brake indicator is related to our driving safety, if it is a fault factor, then it must be repaired in time.

Hello, there is a problem with your braking circuit (the sensor connected to the brake light is faulty) If my answer is helpful to you, please set it to.

Hello, the bulb of the brake light is a double filament, one filament is the car small light, that is, the width indicator light, and the other is the brake light, that is to say, one bulb has two functions. According to the situation you described, there should be a problem with the brake light switch, go to the repair shop or 4S to check!

It's best to go to the 4S store to check it, it doesn't matter if you spend some money, the important thing is safety.

Regarding "what is the problem of the Civic brake light always on", there is the following introduction to the content of the phase code delay:

The reason why the Civic brake light is always on is that there is a short circuit in the wiring or a faulty brake light switch. If the brake fault light on the dial is always on, it is caused by the failure of the brake system, and the parts need to be replaced or brake fluid added in time.

The method of replacing the brake light is:

1. Use a Phillips screwdriver or sleeve to remove the bolts. Pull the light assembly out of the rear pillar;

2. Turn the socket counterclockwise and remove it; Remove the old bulb and insert a new one;

3. Slide the lamp assembly to the guide groove on the body;

4. Align the prongs with the body washers, and Chi then push them in until they fit perfectly.

It is not normal for the Civic brake light to not light up. The brake light does not light up because the bulb burns out, and it needs to be replaced in time; When the brake light does not light up or there is a continuous flashing of the stove, it is necessary to check whether the brake light switch of the car is faulty, and if there is a failure, the brake light switch needs to be replaced in time.

The method of replacing the brake light is:

1. Use a Phillips screwdriver or sleeve to remove the bolts. Pull the headlight assembly out of the rear pillar;

2. Turn the socket counterclockwise and remove it; Remove the old bulb and insert a new one;

3. Slide the lamp assembly to the guide groove on the body;

4. Align the prongs with the body gaskets and push them in until they fit perfectly.

Summary. There are several main reasons why the brake light does not light up. First of all, you need to check whether the fuse of the brake light is burned out, the most likely reason why all the brake lights are not lit is that the fuse is burned out, you can check whether the fuse of the brake light is burned out in the fuse box in your car.

Secondly, it is caused by the damage of the brake light switch, which can directly detect the brake light switch, or you can read the data stream through the computer to see if there is a brake signal. There is a problem with the wiring of your rear tail light or the bulb in the rear tail light, this needs to detect whether there is electricity in the position of the rear tail light bulb, if there is electricity, it is the bulb burned, if there is no power, you must check the relevant lines, including the power line and the iron line. Finally, you have to consider that your body computer is broken, such as the signal of the brake light switch is sent to the body computer, if the body computer is damaged, it will also lead to no brake light control signal output, resulting in the brake light not lighting.

There are several main reasons why the brake light does not light up. First of all, you need to check whether the brake light is burned out, the most likely reason why all the brake lights are not lit is that the safety wire is burned out, you can check whether the brake light fuse is burned out in your car fuse box. Secondly, it is caused by the damage of the brake light switch, which can directly detect the brake light switch, or you can read the data stream through the computer to see if there is a brake signal.

There is a problem with the wiring of your rear tail light or the bulb in the rear tail light, this needs to detect whether there is electricity in the position of the rear tail light bulb, if there is electricity, it is the bulb burned, if there is no power, you must check the relevant lines, including the power line and the iron line. Finally, you have to consider that your body computer is broken, such as the signal of the brake light switch is sent to the body computer, if the body computer is damaged, it will also lead to no brake light control signal output, resulting in the brake light not lighting.

There is no problem with the brake lights, the high-wheel lap brake lights, the driving brake lights are all not lit, the automatic transmission switch brake has a signal, the driving lights are on, and the brakes are not lit. What the hell is it?

Then you now use the computer to test whether there is a relevant brake light signal, you may have a problem with the circuit of the brake light switch.

Here's why. 1. Brake fluid is lacking in base.

2. The tail light bulb circuit is short-circuited.

3. Brake pads are worn and aged.

4. The brake switch is damaged.

5. There is a problem with the sensor of ABS.

Extended information: 1. The brake light is generally installed at the rear of the vehicle, and the main body is a red light to enhance the penetration of the light source, so that even in the case of low visibility, the vehicle driving behind is easy to find the vehicle in front of the vehicle and prevent the accident from happening.

2. The simple model is that the power supply passes the insurance, and then to the brake switch, when the brake pedal is stepped on for braking, the switch is connected, and the electricity is sent to two brake lights and a high-mounted brake light, and is connected with the car body through the negative line to form a loop.