Blue Screen Help 0x00000124 0x00000000, 0x87458024, 0xb6004000, 0x5D00145 What s the problem?

There are quite a few reasons why you take this ** on Google Lookup, so I suggest you go to Microsoft's official website and next debugging tools, this software can analyze the reason for your blue screen in a few seconds, if it doesn't I can send it to you.

There are too many factors for the blue screen of the computer, and there is no way to accurately determine it just by looking at **.

You can use the computer manager, open the toolbox, there is a computer clinic, and directly find the computer blue screen in it, and then you can find the corresponding solution.

Memory address overflow is usually caused by poor contact with the gold finger of the memory or memory corruption. You can remove the memory to clean up the gold finger can not solve the problem, and try to change the memory.

It's not easy for you to write these **, although I don't know how to solve it, but I have to help you top it.

It is recommended that you add how this blue screen appeared, was it after installing some software or something else?

Analyze the reason: Hello, friend! Judging from the ** of the blue screen above, there may be two reasons:

The first reason is that the memory or graphics card is oxidized, and the weather is relatively cold, thermal expansion and contraction, resulting in poor contact between the memory and the memory slot, and the poor contact between the graphics card and the graphics card slot, resulting in hardware incompatibility, and the resulting blue screen phenomenon.

Solution: You can turn off the power first, open the compartment, dial out the memory, use the eraser against the part of the gold finger (that is, the place where there is a copper sheet,) wipe back and forth a few times, and then change a memory slot to insert it back, it's OK, if there is an independent graphics card, you can also use the same method to deal with the graphics card, just don't change the slot, it's OK, if possible, it's best to put the computer's motherboard button battery down, that is to say, remove the button battery for a minute, and then install it back, This saves you from doing the above and makes your computer more stable. Then set the optical drive or hard disk as the startup item,Turn off the software drive,It's OK,The second reason:It's your system poisoned,It will also become a modern number,So Jianyi full antivirus,Reinstall the system or one-click restore,I hope it can help you,I wish you success,Happy

Hello! First of all, the following answers are not network replication, but are the essence of my practice and communication!

The reasons for the blue screen tend to focus on incompatible hardware and drivers, problematic software, viruses, etc.

Suggestion: Troubleshoot the solution as follows:

1. Feel the temperature of the CPU. Whether it is too high. Look at heat dissipation.

2. Whether the hard disk connection is loose; After there is no abnormality, check the hard disk for error;

3. If there is any virus in the system, it is recommended to scan and disinfect the virus in safe mode;

4. Try to restore the BIOS to its factory state;

5. Is the driver of the hardware installed successfully after installing the system?

6. It is best to reinstall the operating system first;

7. If there is still a problem after reinstalling the system, it is very likely that the hardware is incompatible;

8. Consult with the merchant or friends who are familiar with the computer, maybe they will help;

9. Good luck!

I hope I can help you!

Hardware driver error or hardware failure, troubleshooting: 1. Clear the dust in the chassis: After unplugging the power supply, unplug all boards, remove the CPU, remove the motherboard, and completely remove the dust in the chassis.

2. Motherboard discharge: unplug all power supplies, cut off the motherboard battery, and short to clear the CMOS jumper (two or three pins are generally marked with CMOS clear) for 3 to 7 seconds. Then put the battery on.

3. Rust removal and oxide film: unplug the memory stick, expansion card and other plug-ins and wipe the gold finger with an eraser to clean it. 4. Hardware reset installation.

5. Reinstall the system. You try it.