Can Lenovo printers use the powder of brother printers?

The steps are as follows: 1. Remove the toner skeleton from the printer.

2. Press down the clip at one end of the toner skeleton, and then lift the skeleton to separate the toner cartridge from the skeleton.

3. This is the separated cartridge and skeleton.

4. There is a powder spout on the side of the compact, which is covered with a lid.

5. Use a tool to open this stamp, that is, the lid with powder.

6. Before adding powder, you need to pour out the residual waste powder.

7. Then add new toner and close the lid.

8. Put the cartridge back into the skeleton.

9. Replace the toner skeleton with the printer.

There is a chip on the end of the printing drum of the toner cartridge printer, and this chip will record that the ink volume of your ink cartridge has reached the point where you need to replace the ink cartridge, and you can't recover the record even if you add powder.

If the cartridge can be used normally, it will not affect the normal use, but it is more troublesome to print each time, and you need to close the pop-up window.

There may be some computer enthusiasts who can perform online recovery.

The easiest way to do this is to buy a small chip online and replace it if your cartridge lasts for a long time.

If your printer still appears with the words "replace toner cartridge" after adding powder, it means that the printer toner cartridge needs to be cleared, and here is a quick and simple way:

1. Open the front cover.

2. Clear the Return key.

3. Enable key.

4. The plus key (up arrow) - to 11

5. OK key.

6. Close the front cover.

Hello: 1. First of all, we should open the front cover of the machine, which is the place where we open it when we replace the powder. 2. After opening, we can see the prompt on the display screen "The lid is opened, please close".

3. Press the "Clear" button directly on the front panel. 4. Display the words "Replace the toner cartridge Yes No". Then press the enable button.

At this point we can see the display light up, but there is no prompt. 5. At this time, you should quickly press the "+" button on the front panel, observe while pressing, and press "OK" when the display screen shows "11". Note:

When pressing the plus key, be sure to be quick, otherwise it will jump back to the words "front cover open".

Brother printersAfter replacing the toner, you need to open the lid and press and hold the OK key and the plus sign to clear to zero.

Tools Raw Material: Brother Printer DCP-708OD

1. Open the lid of the printer.

2. Find the Clear Li Ye button on the panel and press the Clear button.

3. Then the pop-up box pops up on the panel, and the option is to replace the scrambled toner cartridge.

4. Find the enable button on the panel and press the enable button.

5. Immediately after that, the next step is to adjust the display number to 11, that is, acceptance.

6. Finally, press the OK button, and the clearing is complete.

Summary. Pro: This situation is most likely caused by the fact that you have not cleared the printer, you can press the [Clear Return] button on the control panel to perform the reset operation after replacing the ink cartridge. Here's a closer look:

1. You can try to clear the printer to see if it can solve this problem;

2. Generally, there will be a [Clear Return] button on the control panel of the printer, after replacing the ink cartridge, don't close the lid first, press the clear button;

3. After pressing, a query will appear on the display screen to replace the toner cartridge, press the [Start] button, and then press the number button twice;

4. Generally, there will be relevant completion prompts, and the lid can be closed at this time;

Brother printer still shows replacement toner after adding powder.

Hello, I have seen your question and am sorting out the answer, please wait a while

Pro: This situation is most likely caused by the fact that you have not cleared the printer, you can press the [Clear Return] button on the control panel to perform the reset operation after replacing the ink cartridge. The following is a detailed introduction: 1. You can try to clear the printer to see if it can solve this problem; 2. Generally, there will be a [Clear Return] button on the control panel of the printer, after replacing the ink cartridge, don't close the lid first, press the clear button; 3. After pressing, there will be a query on the display screen to replace the toner cartridge, press the [Open Front] button, and then press the number button twice; 4. Generally, there will be a relevant silver pai kai to complete the prompt, and the lid can be closed at this time;

After adding powder; Lenovo's Don't Forget to Clear Zero; Here's how: "Turn it off, open the front cover, press and hold the button on the machine with one hand, and turn on the switch with the other." (Just press and hold the start button to turn on, press and hold) - then all the lights are on, and the ready lights are off.

After letting go, press "2 times" in a row (remember that it is 2 times, you can't press more), and the lights are on again, and then press "5 times" in a row after letting go, and close the door".

If the machine is adding powder for the first time, the original toner inside must be cleaned.

Otherwise, the original toner inside is mixed with the toner you take, and the printed effect is a mess!

Unless you're taking the original toner (I was trying to save some toner for the customer, I didn't pour out the inside, and then I wasted the toner I took, and finally poured it all out, cleaned it up, and added a new bottle).

The method of adding powder is as follows:

Open the front panel of the machine, hold the toner cartridge handle, and pull it out firmly.

And then there's a blue button on the left side of the toner cartridge, and when you press it, the cartridge and cartridge can be separated.

There is a plastic lid on the left side of the compact, and when it opens, it is the powder filler.

Add the toner and close the lid and then need to reset.

Reset Steps: There is a semicircular slot on the left side of the cartridge with a white handle inside.

Just pull the handle up from underneath and break it with a screwdriver (not recommended, it may damage the gears, which is how I did it when I didn't know it at first.) You can also turn the stick in the opposite direction (that is, in your direction), and while you turn, the white wrench will automatically move up slowly, and after moving up, the powder is basically done.

It is recommended to clean the corona wire by the way after adding powder (otherwise the machine may "clean the corona wire" and not print).

It's the green square on the top of the toner cartridge, and it's going back and forth a few times, and there's a sponge underneath it, and it's going to clean up the corona wire.

Hello dear! After the Brother printer adds toner, it still prompts the reasons and solutions to replace the ink cartridge as follows: 1. If the ink cartridge is fine, turn off the printer, and then connect it again. 2. Or you should pay attention to the position of your printer, if there is a problem with the placement of the printer, it will also cause it to not work.

3. If it doesn't work, turn off the printer with lead socks, then take out the ink cartridge, and then align it to install it. Not yet, check the driver, reinstall the driver. 4. If none of the above can be solved, Duan Shi may be that the metal sheet on the cartridge has not been used for a long time, and the contact is poor, so he must take out the cartridge and then wipe it clean with an eraser, and you will find that the metal sheet on the cartridge is shiny.

If you install it again, there will generally be no problem. 5. If the problem cannot be solved, it is necessary to consider whether the cartridge is damaged, and it is recommended to replace the cartridge. 6. It is recommended to contact professional maintenance personnel for maintenance, hoping to help you!