Why does the mouse sometimes get stuck and don t move

1. The solution that the mouse can sometimes move and sometimes get stuck:

1. After pulling the mouse out of the computer, disassemble it, and thoroughly clean the dust on the light-emitting diode and optical lens assembly at the tail of the circuit board with a clean paper towel or dry soft cloth (the optical lens assembly is pressed by the circuit board, and after picking up the circuit board, a relatively large white transparent triangular device you see is it).

2. Replace the mouse pad (it may be caused by the wear and tear of the mouse pad).

Second, the mouse can't work at all, and the solution to the problem that can't move all the time:

1. Check whether the mouse interface on the computer is loose or falling off;

2. Check the junction between the mouse line and the mouse to see if the mouse line is broken here (if so, the wire can be connected).

3. Disassemble the mouse and check whether the four mouse wire joints on the circuit board are broken or in poor contact (if so, soldered);

Regarding the problem of the mouse suddenly getting stuck and not moving, there may be some netizens who are not very clear, so let me tell you the reasons and solutions for the sudden stuck mouse, I hope it can help you!

Analysis of the reasons why the mouse suddenly gets stuck and does not move 1:

How to fix your computer stuck: Open Task Manager.

This is also a very quick little solution, although it can't solve the lag phenomenon fundamentally, but it can be quickly alleviated, and then we can use other measures, that is, open the task manager (ctrl+alt+delte)!Put our mouse on the bottom blank space and right-click, after right-clicking, you will see that the task manager has finished a few processes, and you can increase the speed of the computer. Sometimes you end a few processes and you find that the speed is significantly improved, and the lag does not occur for a short time, temporarily saving the computer.

How to fix your computer stuck: Clean up the dust from your computer's fan.

This is a palliative solution, of course, based on the fact that the computer fan is too dusty. Sometimes, if the computer itself is too dusty, it will also affect the speed, because the fan has too much dust, and the fan blades are covered with dust, and there is no way to run quickly and dissipate heat well. When the hot air is deposited inside the computer, the phenomenon of jamming is more likely to occur, at this time, we only need to go to a professional computer repair center to clean up the dust.

The solution to the computer stuck: add a memory module.

Sometimes the computer card is not because of internal factors, but because some hardware devices are not in place, and small memory is also a common problem in computers. If our computer has been used for a long time, it is also normal for the memory to become smaller, because the software is now updated, and the volume will increase with each software update. At this time, it is normal to have insufficient memory, and we can consider adding a memory module, and the computer jamming phenomenon can be alleviated a lot.

Analysis of the reasons why the mouse suddenly gets stuck and does not move 2:

The hardware is worn, and the mouse port is very easy to disconnect, which needs to be paid attention to.

If the memory is too low, the computer will crash and freeze, causing the mouse to be unable to move.

Software conflicts, computer poisoning, causing the mouse to not move, moving stuck.

Press Alt+F4, use the key to select Restart, and then press the Tab key to select OK, at this time the mouse will generally resume use.

2. Or use the arrow keys to find the computer, press the text key, select Properties, and press Enter.

3. Press the Tab button, select Device Manager, press Enter, then use the arrow keys to select the mouse and other pointer devices, press the right arrow button to select the device, select the mouse model, and press Enter.

4. Press the Tab key and the right arrow key to switch to the driver bar, then press the Tab key, select Update Driver, and press Enter.

Precautions for the maintenance of computer mice

Computer mice are the most water-avoiding, so we must not get water on our hands before holding the mouse, if we really want to use it, we must dry the water on our hands before using it.

When we use the mouse, we should not knock and shake it too hard, as this will damage the parts of the mouse.

When we use the mouse, it is best to put a mouse pad on the mouse to prevent the mouse from being damaged due to the rough surface of the table during the mouse movement.

We should not have greasy and dust on our hands when using the mouse, which will reduce the function of the mouse, because greasy and dust are easy to form grease and dirt at the mouse.

When we use the mouse, we should not click too fast and too hard, which will make the mouse easy to damage.

When using the mouse, do not use the mouse while eating snacks, which is not only unhygienic but also easy to make the snack residue fall into the mouse and jam the mouse, affecting the performance of the mouse or even damage.

Summary. It may be that the mouse is not compatible with the system, the reason for this problem may be the system version, the configuration is too low, and the mouse driver configuration is high, so there will be a card situation, first you can try to press the mouse on other computers to see if the previous problem occurs, if so, it may be that the mouse itself is not in good contact, it is recommended to change the mouse, if not, you can try to uninstall the mouse's driver, and then reinstall it. There is another method, you can try it, I don't know if it will work for you in this situation, open the "Control Panel", double-click the "Mouse", select "Hardware", click "Properties", select "Advanced Settings", set the sample rate to "200" and change the "Input Buffer Length" to 100, click OK, and then see if the mouse becomes useful.

The mouse suddenly gets stuck and doesn't move, and then, what should I do if it's stuck again.

Hello may be the mouse and the system is not compatible, the reason for this problem may be the system version, the configuration is too low, the mouse drive configuration is high, so there will be a card situation, first you can try to press the mouse on other computers, to see if the previous kind of problem occurs, if so, it may be that the mouse itself is not in good contact, it is recommended to change the mouse, if not, you can try to uninstall the mouse's driver, and then reinstall. There is another method, you can try it, I don't know if it will work for you in this situation, open the "Control Panel", double-click the "Mouse", select "Hardware", click "Properties", select "Advanced Settings", set the sample rate to "200" and change the "Input Buffer Length" to 100, click OK, and then see if the mouse becomes useful.

I hope you are satisfied, and if you have any other questions, please continue to consult me.

Now even the cursor is gone<>

Check the connection port between the mouse and the computer to see if the contact is not good.

Use the arrow keys to find your computer and click on the text key on the right side of the keyboard between the Alt and Ctrl keys. Then use the arrow keys to find Manage, and click Enter.

Use the arrow keys to find the device manager, hold down the tab key + arrow keys to find the mouse and other pointing devices, select the mouse model, and press enter.

Press the Esc key to go back and click Enable Program. If it still doesn't work, you need to consider replacing the mouse.

I hope you are satisfied, and if you have any other questions, please continue to consult me.

1. Click the Start icon and select Control Panel.

2. Change the viewing mode to a large icon and select Mouse.

3. In the Mouse Properties window, select Hardware Options and select Properties.

4. In the interface, select the Driver option and select Update Driver.

5. In the following prompt box, select OK.