The automatic kettle keeps the water boiling? The automatic kettle keeps pumping and adding water

If the water is boiling non-stop, in this case, the automatic power-off system inside is broken, and you can get the after-sales service and let the master help you replace the power-off switch inside.

Generally speaking, if this normal water is boiled, it will automatically turn off in about two seconds or one second, so it will be relatively normal, if there are other situations, it means that his equipment is malfunctioning.

If the water is boiling, it will stop, but if it doesn't stop, it means that there is a problem with the kettle, and generally speaking, it may wait a few seconds before it will return to normal.

It may be that there is a problem with the internal wiring of the machine, and it is recommended to overhaul the electric kettle. It can be repaired as follows: first of all, the kettle must be put on, otherwise the system will not recognize the kettle, and it will not let you add water.

This shows that there is a problem with the thermostat of the automatic kettle, so it will not stop, and this can be replaced by after-sales service.

Dismantling and repairing one, it is something similar to shrapnel that induces temperature, and it should reach a certain temperature The shrapnel deformation opens two contact points, turns off the power, and stops heating. One of these options is just that.

This situation is most likely due to the loss of connection of the circuit, so it is necessary to find the cause in this regard, and only then can a good effect be achieved.

The water in the kettle is boiled on the automatic, if it doesn't stop, it means that the control of the water stop, Lintong County did not jump away, so he can not stop and can find a professional master to replace a Lintong line.

In this case. It is a temperature control switch that automatically feeds the water temperature of the kettle. Teacher's School. And when the temperature reaches a certain level, the temperature control switch cannot automatically power off. That's why the kettle is open, and it doesn't stop. Replace the water temperature control switch in time.

That means that the expansion switch under you is broken, that is, there is a temperature measurement at the bottom, and then when the water is 1 to 100 degrees, it is a feeling of thermal expansion and cold contraction, and then the electricity is cut off.

Well, it has a drain in the kettle, and it may be that the drain hole inside is blocked. You can clean the drain inside, and it should be normal to clean it.

If this kind of problem occurs, it should be that the switch of the automatic kettle is connected to the electricity, so it is good to change the switch.

Some of them are set at a fixed time, and they will stop when the time comes, but in general, there are fewer intelligent ones.

The water is still heating when it is boiling, and it is estimated that the temperature sensing element or heating pipe is constantly turned off.

If you boil this water, you just need to take it down and drink it, right? There's no need to keep burning.

It may be that there is a problem with the internal wiring, and it is recommended to overhaul its interior. It can be repaired by the following: first put the kettle up, otherwise the system will not recognize the kettle and will not let you add water.

Secondly, can you hear the pump pumping sound after clicking on the pumping, if you don't hear it, it is the pump problem.

Related Notes:A kettle is a container for water. There are many kinds of materials, which can refer to metal kettles for boiling water, or portable drinking water pots, which are mainly divided into five categories: 1. Plastic (main material) 2, stainless steel 3, aluminum alloy 4, ceramic 5, other materials, can be heated by electricity or directly by fire.

1. Electric kettle: boiling hot water, which is ready to use, is mostly used for making tea;

2. Water bottles: they are divided into those that are kept warm and those that are not kept warm;

3. Thermal insulation kettle: double-layer stainless steel vacuum thermos kettle, as well as double-glazed thermos kettle, which are mostly used for hotels, clubs, conference rooms, and household hot water needs.

Check whether the thermostat is damaged, whether the heating switch is normal, both of which are fine, that is, the electric heater is damaged and can only be replaced.

First of all, the kettle should be put on. Otherwise, the system will not recognize the kettle and will not let you add water. There is also whether you can hear the sound of the pump pumping after you click on the pump, if not, it may be the problem of the pump.

Look at the pump and see if it still spins.

If you turn it, it may be that the internal impeller or some other accessory is damaged.

1. Failure to work normally: (1) Poor line contact, overhaul socket and wiring. (2) If the sensor or other components are damaged, send them to the repair department for repair.

2. If it can work normally, only the display is abnormal, and the display board is damaged, and the display board will be used or sent to the repair department to replace the display board.

3. There is a problem with the water pump, or the pot is not sensing.

4. There is also a situation that is the problem of the connecting line inside!

5. Whether the pipeline is blocked, secondly, consider whether there is air leakage in the pump pipeline system, and thirdly, consider whether the pump is broken, and see whether the electric pump is turning.

6. Check all parts of the machine first to see if there is any appearance deformation. Then open the lid of the barrel to observe, whether there is a foreign object in the barrel to hinder the water supply control float movement, whether the water pressure reaches the required pressure, some of the water supply control is a solenoid valve to see if the circuit is broken, generally there will be no external force damage will not be a problem, and then see if it meets the installation requirements.

The reasons are as follows: 1. The failure of the automatic controller will transmit the wrong signal or the signal cannot be transmitted, resulting in the inability to get on the water. At this time, the control panel should be replaced in time.

and sensors. 2. Water pressure problem: If the water pressure is too low, it will also lead to the inability to get on the water, so buy a booster pump when the water pressure is large.

This ensures that the water is served.

A water dispenser is a device used to fill a kettle, which draws water from an external tank through a water pump, and then transfers the pumped water to the kettle. Streamlined appearance design, humanized structure design.

Beautiful and stylish, easy to operate.

Summary. If the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two.

If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired.

2.It is not heated after pumping, but the indicator light is on.

The indicator light is on, indicating that the power supply has been added to the indicator circuit, and the fault is in the electric heating pipe or its connecting part, and the electric heating pipe is damaged and the contact is poor. Remove the electric heating pipe and measure its resistance value. The electric heating pipe is damaged and can generally only be replaced.

The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, which can be disassembled and repaired by the switch box, and it is best to replace it with a new one if the damage is serious.

3.Water can't boil, and electricity can't be cut off.

This is mainly due to the failure of the reset switch. Common reasons are severe deformation of the thermostat or obstruction of the operation of the switch linkage. For the former, the convex angle of the small tongue of the thermostat can be rebent to make it push the switch connecting rod normally.

For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position.

4.Slow heating rate.

Common origins. What happens when the kettle does not pump water on the auto water.

If the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two. If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired.

2.After pumping, it is not heated, but the indicator light is on, indicating that the power supply has been added to the indicator circuit, and the fault is in the electric heating pipe or its connecting part, and the common electric heating pipe is damaged and the contact is poor. Remove the electric heating pipe and measure its resistance value.

The electric heating pipe is damaged and can generally only be replaced. The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, which can be disassembled and repaired by the switch box, and it is best to replace it with a new one if the damage is serious. 3.

The water cannot boil, and the power cannot be cut off, mainly due to the failure of the reset switch. Common reasons are severe deformation of the thermostat or obstruction of the operation of the switch linkage. For the former, the convex angle of the small tongue of the thermostat can be rebent to make it push the switch connecting rod normally.

For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position. 4.Slow heating is a common cause.

The common cause of slow heating speed is that the power supply voltage is too low, and the indoor power supply line or plug socket is not in good contact, which should be ruled out first. Then check whether the electric heating pipe is seriously fouled, whether the contact between the base and the power plug holder of the pot body is seriously bad, etc. If the electric heating pipe is fouled, you can scrape it with a knife first, and then polish it with fine sandpaper.

If the contact between the base and the power plug holder of the pot body is seriously poor, you can first remove the oxide layer and dirt of the contact piece and contact of the plug holder, and then correct its shape to make the contact between the two close and good.

Summary. The reasons for the automatic power off of the electric kettle: 1. The electric kettle will reach 100 degrees after a few minutes of powering on, and the temperature control switch will automatically cut off the power supply; 2. In the case of water, the power will be automatically cut off if the water is not boiled, indicating that the temperature control switch has been damaged.

The reasons for the automatic power failure of the electric hot water kettle: 1. The electric kettle will reach 100 degrees after being powered on for a few minutes, and the temperature control switch will automatically cut off the power supply; 2. In the case of water, the water will automatically turn off if the water is not boiled, indicating that the temperature control switch has been damaged.

The working principle of the electric kettle: the water vapor produced when the water boils makes the double gold bucket of the steam temperature sensing element deform, and this deformation pushes the power switch to power off through the lever principle, and the power-off air balance is not self-resetting, so the water Qingpin kettle will not automatically reheat after the power is off.

Hello dear, what's going on with the automatic kettle not heating up all the time: 1. Maybe the pump is broken. First see if the pump motor is rotating, if not, check whether the pump motor is broken.

2. It may be that there is air in the inlet pipe. Check that there is no air in Fudan, and the air should be fine. 3. It may be caused by incorrect use.

Put the kettle on the thermostat, and then double-click to pump the water, it's OK 4, the circuit board is broken, press the following other function keys to see if it can be reflected, no response means it is broken. The working principle of the electric kettle in the hall is that the water vapor generated when the water boils deforms the bimetal sheet of the steam temperature sensing element, which is deformed by the lever principle to push the power switch to power off. It is not self-resetting when it is powered off, so the kettle will not automatically reheat after the power is off.

Summary. 1.Check whether the water pipe is blocked or leaking, if there is a blockage or leakage, please repair it in time; 2.

Check whether the water pipe receives the signal of excessive water pressure, this problem may occur because the water pressure is too high, and the water pressure needs to be lowered; 3.Check for power and water** failures; 4.Check for control system failures, which may be caused by a malfunction in the temperature switch or control system.

1.Check whether the water pipe is blocked or leaking, if there is a blockage or leakage, please repair it in time; 2.Check whether the water pipe receives the signal of excessive water pressure, this problem may occur because the water pressure is too high, and the water pressure needs to be lowered; 3.

Check for power and water** failures; 4.Check if there is a control system so that the sun key sells the fault, which may be due to the temperature switch or the control system failure caused by the brightness width.

The best solution is to check the water inlet of the tank to see if there is any blockage or contamination, and if so, try to clean or replace the water inlet. If there is nothing wrong with the water inlet, you need to check the valve of the tank to see if there are any faults, and if so, you should try to repair or replace the valve. In addition, you can also check whether the water tank exceeds the allowable water level, such as the stuffy ear fruit, you should try to adjust the low water level.

Summary. Hello dear, the automatic water addition when the automatic kettle is heated is solved as follows. The internal line is disordered or the connection line at the automatic water button leads to automatic addition.

It is not recommended to plug it in. It may be that there is a problem with the internal wiring, and it is recommended to overhaul its interior. Automatic boiling water will automatically add water when the switch is turned on, when the water reaches a certain temperature, it will stop working, when it is lower than the minimum temperature, it will automatically work The steam switch is broken, when the steam switch metal temperature sensing device is bad or damaged, it will cause the water to not jump away in time after boiling, and continue to heat.

Have a great day! All wishes come true, <>

Hello dear, the automatic water addition when the automatic kettle is heated is solved as follows. The internal line is disordered or the connection line at the automatic water button leads to automatic addition. It is not recommended to plug it in.

It may be that the internal wiring is asking Sun Yuye to shout and laugh, and it is recommended to overhaul its interior. Automatic boiling water will automatically add water when the switch is turned on, when the water reaches a certain temperature, it will stop working, when it is lower than the minimum temperature, it will automatically work The steam switch is broken, when the steam switch metal temperature sensing device occurs when it is bad or damaged, it will cause the water to not jump away in time after boiling, and continue to heat. Have a great day!

All wishes come true, <>

That's not what it means.

Dear, it's the kettle that keeps the water on it, and it won't stop automatically, isn't it!

It's not that after adding water, it still ticks and keeps flowing small water.

I'll send you a ** to take a look.

Uh-huh, okay.

It's just ticking all the time.

Hello in China, you are the faucet there has been broken, to replace it with a new one. It may be that the faucet is broken when it moves up and down. The temperature on our side will freeze if it is too low, anyway, it will be reset, and Li Peixin will always drip water, so he can only replace the faucet. This round can't be saved.

Yes, I also have such a broken one, continuous switching, the faucet will be broken, and you can only replace it.

I'm going to change this.

Is there a single sale of the bar-type model?

Points, there are many models, I can't see what model is in the city, take a few more ** go to the hardware store and ask. It's usually available.

By the way, you can also try to see if you can remove it, and if you can remove it, you can take it directly to the hardware store to compare the model. Remember to turn off the main valve of the water when dismantling.