HP Aftermarket HP 15G AD110TX Notebook Tutorial 100

Step 1: Preparation.

Prepare the tools (fine Phillips screwdriver, flathead screwdriver, tweezers, blade, soft cloth) and the notebook to be disassembled.

Step 2: Remove the battery.

With the back of the laptop facing up, open the battery's retention latch and remove the battery.

Step 3: Remove the back guard.

Disassemble the fixing screws of the two guards on the back of the notebook and remove the guards.

Step 4: Remove the hard drive.

Unplug the hard disk cable and take out the hard disk.

Step 5: Disassemble the NIC.

Gently pull out the network card from the data slot, gently pry open the metal clip of the power cord, and take the network card out.

Step 6: Remove the buckle bar.

With the notebook facing up and the LCD screen on, gently pry open the upper buckle bar of the keyboard and turn it up, and then open the cable connected to the motherboard and take out the buckle.

Step 7: Disassemble the keyboard.

Gently pry the keyboard open and flip it up (be careful not to tear off the cable underneath), disassemble the cable, and remove the keyboard.

Step 8: Disassemble the LCD screen.

Disassemble the two cables between the LCD screen and the motherboard, including power and data, unscrew the display fixing screws, and take the display screen.

Step 9: Disassemble the touchpad.

Gently disassemble the cable connecting the touchpad from the motherboard and remove the main case of the touchpad.

Step 10: Disassemble the optical drive, etc.

Remove the fixing screws and remove the optical drive, heatsink and fan on the back.

Step 11: Disassemble the motherboard.

Unplug the sockets of the cable and the next cable, and then pay attention to the cable below when removing the motherboard, and remove the motherboard and accessories.

Step 12: Disassemble the memory.

Gently push the memory module to the sides to secure the metal clip, the memory module will pop up, and then pull out the memory module.

Step 13: Disassemble the CPU

Release the metal clip of the CPU and pull out the CPU.

Web Links. I wrote it down.

1. First of all, loosen the two screws on the back as shown in the picture below, and then move on to the next step.

2. Secondly, remove the right cover. There are no screws on the side covers, only clasps. Take care to remove the bottom first and then the top. The buckle in the middle of the top is the most difficult to remove. The bottom must be pulled out first and with a screwdriver.

Press up. The buckle in the middle can be pulled out again, as shown in the image below, and then move on to the next step.

3. Next, remove the left cover in the same way, as shown in the picture below, and then move on to the next step.

4. Then, loosen the top cover screws as shown in the figure below, and then proceed to the next step.

5. Subsequently, remove the top cover connecting rod latch, as shown in the figure below, and then enter the next step.

6. Next, press the buckle in the lower right corner of the front cover, as shown in the figure below, and then enter the next step.

7. Then, Shoumin pressed the buckle in the lower left corner of the front cover, as shown in the figure below, and then Iwachi entered the next step.

8. Subsequently, remove the front cover, as shown in the figure below, and then proceed to the next step.

9. Next, flip the top cover to the coarse celery as shown in the figure below, and then enter the next step.

10. Then, remove the top cover as shown in the figure below.

11. Finally, remove the back cover.

Prepare tools (Phillips screwdriver, flathead screwdriver, tweezers, blade, soft cloth) and the notebook to be disassembled.

Steps to remove the integrated back cover.

After putting the notebook on the towel and start to remove the screws with a Phillips screwdriver, I have marked the screws for you, remember the position of each screw during the disassembly process, do not confuse.

Pry down on the other side of this place until you hear a click, and then continue to pry along the periphery, continue to have a clicking sound, pry around, pay attention to the discarded bank card can be pryed, if you pry with an iron tool it is best to wrap a piece of cloth outside, otherwise it will pry out traces.

I haven't looked at this model of notebook at all, so you can take it apart and try it according to this method.

It is recommended to call to confirm the specific time schedule of the maintenance center, and if you cannot get through on the weekend**, it is recommended to call from Monday to Friday.

We hope you find the above reply helpful.

1. Because the notebook is a high-precision electronic device, if it has not undergone professional training, it is easy to cause hardware failure if it is disassembled and assembled by itself. Problems with the machine caused by self-disassembly and assembly may affect the warranty of the machine, please consider carefully. If you must disassemble and assemble it personally, the following English manual, page 41 100 is the disassembly and assembly instructions, you can refer to it:

We hope you find the above reply helpful.

Well, that tells you won't tear it down.