Why is the host dripping when the host is turned on after installing 8G memory, and the screen is bl

Maybe the motherboard is not compatible with you.

Please put the memory on the motherboard.

The CPU model is reported.

Please refer to the motherboard manual. Generally, it is a single 2G, double-sided memory module. Single-sided, narrow-striped, and some brands are not supported. Please read clearly when buying.

It may be a memory compatibility problem.,You plug in one and try it first.,The motherboard is dripping.,It's the memory and the motherboard are not in contact.,Of course, the screen is black.,Your host is equal to not getting up.,The head show upstairs is funny.,And use Master Lu.,You give me Master Lu a look at me.,I can't turn it on.,Lu your sister.。

Obvious poor memory contact, replug the memory module.

The memory module and motherboard are not compatible, and you did not buy the right model.

First of all, your computer doesn't boot properly!!If the model is not the right for your computer, you first make sure that your memory module is plugged in too many times, if it doesn't work, the model is not the right for your computer, or it is not compatible.

If you see if it's plugged in tightly, if it still doesn't work, there is a problem with the memory.

There is noise in the computer after the memory module is installed, which is caused by the corruption of the computer's memory module, and the specific solution is as follows:

1. First of all, turn off the power of the computer and unplug all the wires connected to the computer

2. Then, open the case of the computer, and then you can clearly see the internal structure of the computer

3. Then you need to find the location of the memory slot inside the case:

4. You can see that one side of the memory module has been cocked and detached from the buckle

5. Press it down by hand so that both sides of the memory module are stuck on the buckle, and then close the case and turn it on again without noise

After ruling out the reason that the memory module is not installed properly, it is most likely caused by the incompatibility of the memory module.

Attention should be paid to the installation of memory modules:

1. What kind of memory module to add depends on what the original memory of the computer is. The most important consideration for expanding memory is compatibility.

2. Pursuing high clock speed too much without considering compatibility issues will lead to unstable memory or failure to boot.

3. It is more appropriate to use the original memory module version to slightly increase the memory module capacity value.

The memory module is incompatible, and the self-test cannot be passed.

1. Take an eraser to erase the gold finger.

2. Try a different memory slot.

3. Replace the original memory.

4. Your motherboard does not support new memory modules, so get a new one.

The memory is not plugged in, or the memory is incompatible. Unplug the memory and reinsert it to see, it still doesn't work, only to change the memory.

Then the problem lies in the memory module. Try unplugging it again, or you can replace it with another memory module

If the memory is not compatible, try it again, or get one from another old computer.

Laptop black screen, this situation occurs, generally there are the following aspects:

1. After booting up, it emits a continuous sound of "Di Di", black screen, which is a fatal error of the system and cannot be continued, and the alarm is given by the speaker, indicating that the memory module is damaged, or the memory module is polluted by the gold finger, or there is too much dust in the memory slot.

2. After booting up, there is a continuous sound of "beep", the screen is black, there is no heating on the surface of the CPU, or the heat generation is obviously low, which is generally due to the damage of the voltage adjustment tube on the motherboard.

The memory module is not compatible with the notebook, so take it off as soon as possible.

There is noise in the computer after the memory module is installed, which is caused by the corruption of the computer's memory module, and the specific solution is as follows:

1. First of all, turn off the power of the computer and unplug all the wires connected to the computer

2. Then, open the case of the computer, and then you can clearly see the internal structure of the computer

3. Then you need to find the location of the memory slot inside the case:

4. You can see that one side of the memory module has been cocked and detached from the buckle

5. Press it down by hand so that both sides of the memory module are stuck on the buckle, and then close the case and turn it on again without noise

Didi ring, all the time, is the alarm sound that the computer motherboard thinks that the memory has not been found.

Apparently caused by the memory not plugged in.

1. Check whether the memory is plugged in. Generally, if it is not plugged in, it will call the police, but sometimes the alarm cannot be heard if the alarm is not called or the buzzer is broken. Reinsert it carefully.

2. If it doesn't work, it may be that the quality of the memory module is not good. The new memory will be returned directly, and the old memory will be erased with the gold finger of the memory.

3. If there are multiple memories, insert a separate test to see if it is normal. to determine whether it is a single quality problem or incompatibility. Or swap the two memory slots.

If that doesn't work, check whether the new memory is the same as the old memory. In addition, the new memory should use double-sided memory as much as possible, which is more compatible.