The sound of the mouse buttons is so loud, and the mouse keeps making a noise when plugged into the

Too loud is actually because the spring tongue of the spring blade in the micro switch is too bent.

Solution:1Open the photoelectric mouse cover, the general mouse cover is composed of two parts, first flip the mouse and place it, remove the screws on the lower part of the mouse cover, take out the lower part of the mouse cover from the whole mouse, and then take out the upper part, so that the internal structure of the mouse is presented in front of you.

2.Locate the microswitch. The micro switch is located below the mouse button, and there are generally three, one left button, one right button, and a middle wheel button.

Microswitches are generally rectangular, and a few are round. There is a small protruding strip on the switch, which is the part where we really press the button when we usually press it.

3.Remove the upper part of the micro switch. The micro switch is divided into two parts, the lower part is connected to the circuit board, and the upper part is composed of the cover of the upper part and the spring inside.

The upper and lower parts have two clips stuck (on the two sides of the long rectangle, which is easy to see), so that they are connected and will not be separated. Locate the stuck point and use a knife or toothpick or other tiny object to top it open.

4.After removing the upper part of the micro switch, you can see the spring inside, bend the middle part of the spring again, and then try the sound and elasticity of the button at this time, and then adjust the curvature of the bending repeatedly. 5.Rehabilitation.

ps can be used with a needle to gently pry open the micro switch.

If you don't think it's easy to use, you can change it, and now the mouse is not expensive.

This is because the sticky key is turned on in the computer system, and it is only necessary to turn it off in the system.

Tool: Computer.

1. Click the start button in the lower left corner of the computer desktop, and click [Control Panel] on the pop-up menu.

2. Click [Easy Access] at the bottom of the interface.

3. Continue to click [Change the working method of the keyboard] under the Ease of Access Center.

4. The checkmark in front of the sticky key will be enabled to cancel.

5. Finally, click [OK] below, and then press the keyboard after clicking, and there will be no sound.

1.Why does my computer have mouse sounds that don't stop.

Hello, are you poisoned or something, it should be taking up your memory, causing your point to be delayed in mouse sounds.

First of all, check if your mouse is stuck, and change the mouse to see if it is still in this condition.

If it's not a mouse problem, try it with antivirus software or right-click on the volume speaker in the lower right corner of the computer, select Adjust Audio Properties, and select the Sound Tab to set it inside.

Or take a look at it with a different mouse.

Of course, this may be the operating sound of the system, that is, some operating systems, when you don't move the mouse, will emit some identical sounds on its own two or more times in a row.

2.Why is it that there is always the sound of the mouse clicking on things in the computer, and I don't move the mouse, and the mouse doesn't either.

First, first confirm that the hardware is fine. If the speaker is fine, the sound card is fine, and if you've tested it on other machines and it's really good, then you can read on.

2. Make sure all the cables are exactly right. Then power on the speaker and turn on the volume switch.

3. Install the driver of the sound card correctly, if it is an onboard sound card, it is best to install the driver provided on the driver disk of the motherboard.

In fact, the computer does not make a sound, and many times it is because the sound card is not driven correctly. In general, after the sound card driver is installed, there will be a small speaker icon in the taskbar in the lower right corner. ）

Fourth, if you are sure that the driver is installed correctly, then take a look at the volume settings in the computer.

The specific method is to double-click the speaker icon in the taskbar, and check whether the volume is turned off to the minimum in the "Volume Control" and "Waveform" dialog box in the pop-up "Volume Control" and "Waveform".

If these two options are not available in the dialog box, click on the "Options" menu - select "Properties" - select "Volume Control" and "Waveform" in the "Show Volume Controls" and then set them correctly.

Note: Step 4 can only be set up after the driver for the sound card has been installed correctly.

Hello, if the mouse is plugged into the computer and keeps ringing, which limb can you regret trying the following solutions:1Check if the mouse connection is stable:

Sometimes a bad contact of the mouse socket can also cause a noise, and you can try to reinsert the mouse or replace the socket. 2.Update Mouse Drivers:

If you are using a wired mouse, you can try updating the driver of the mouse, there may be an issue that the driver is not compatible with the operating system. 3.Clean the mouse wheel:

If you're using a Besar mouse with scroll wheels, it may be because the wheels are affected by dust, dirt, etc., you can spray it around the wheel with a detergent and wipe it off with a tissue or cotton swab. 4.Replace the mouse:

If the above methods do not solve the problem, it may be that your mouse is faulty, and you can consider replacing it with a new one.